EN 10217-6:2002
(Main)Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties
This Part of EN 10217 specifies the technical delivery conditions in two test categories of submerged arc welded tubes of circular cross section, with specified low temperature properties, made of non-alloy steel.
Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 6: Unterpulvergeschweißte Rohre aus unlegierten Stählen mit festgelegten Eigenschaften bei tiefen Temperaturen
Dieser Teil der EN 10217 enthält die technischen Lieferbedingungen für unterpulvergeschweißte Rohre mit kreisförmigem Querschnitt aus unlegierten Stählen mit festgelegten Eigenschaften bei tiefen Temperaturen und legt dafür zwei Prüfkategorien fest.
Tubes soudés en acier pour service sous pression - Conditions techniques de livraison - Partie 6: Tubes soudés à l'arc immergé sous flux en poudre en acier non allié avec caractéristiques spécifiées à basse température
La présente partie de l'EN 10217 spécifie les conditions techniques de livraison, pour deux catégories d'essai, des tubes soudés à l'arc immergé sous flux de poudre à section circulaire en aciers non allié, avec caractéristiques spécifiées à basse température.
Varjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 6. del: Obločno pod praškom varjene nelegirane jeklene cevi s specificiranimi lastnostmi za delo pri nizkih temperaturah
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 6: Unterpulvergeschweißte Rohre aus unlegierten Stählen mit festgelegten Eigenschaften bei tiefen TemperaturenTubes soudés en acier pour service sous pression - Conditions techniques de livraison - Partie 6: Tubes soudés a l'arc immergé sous flux en poudre en acier non allié avec caractéristiques spécifiées a basse températureWelded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific use23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 10217-6:2002SIST EN 10217-6:2003en01-april-2003SIST EN 10217-6:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10217-6May 2002ICS 23.040.10; 77.140.75English versionWelded steel tubes for pressure purposes - Technical deliveryconditions - Part 6: Submerged arc welded non-alloy steel tubeswith specified low temperature propertiesTubes soudés en acier pour service sous pression -Conditions techniques de livraison - Partie 6: Tubes soudésà l'arc immergé sous flux en poudre en acier non allié aveccaractéristiques spécifiées à basse températureGeschweißte Stahlrohre für Druckbeanspruchungen -Technische Lieferbedingungen - Teil 6:Unterpulvergeschweißte Rohre aus unlegierten Stählen mitfestgelegten Eigenschaften bei tiefen TemperaturenThis European Standard was approved by CEN on 25 April 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10217-6:2002 ESIST EN 10217-6:2003
European Standard series covering tubes for pressure purposes is:EN 10216:Seamless
steel tubes for pressure purposes.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 10217-6:2003
of steel tubes – Part 9: Automatic ultrasonic testing of the weld seam ofsubmerged arc-welded steel tubes for the detection of longitudinal and/or transverse imperfections.EN 10246-10, Non-Destructive Testing
of steel tubes – Part.10: Radiographic testing of the weld seam ofautomatic fusion arc-welded steel tubes for the detection of imperfections.EN 10246-15, Non-Destructive Testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/ plate used inthe manufacture of welded steel tubes for the detection of laminar imperfections.EN 10246-16, Non-Destructive
Testing of steel tubes - Part 16: Automatic ultrasonic testing of the area adjacent tothe weld seam of welded ste
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.