EN ISO 10893-11:2011
(Main)Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011)
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011)
ISO 10893-11:2011 specifies requirements for the automated ultrasonic shear wave (generated by conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric resistance and induction-welded (EW) steel tubes.
For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by agreement, perpendicular to the weld seam or both.
For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam. In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer.
ISO 10893-11:2011 can also be applicable to the testing of circular hollow sections.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in Längs- und/oder Querrichtung (ISO 10893-11:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die automatisierte Ultraschallprüfung unter Anwendung von Transversalwellen (erzeugt mittels konventioneller oder mittels Phased-Array-Technik) der Schweißnaht unterpulvergeschweißter (SAW-), elektrisch geschweißter oder induktionsgeschweißter (EW-) Stahlrohre fest. Für unterpulvergeschweißte (SAW-) Stahlrohre umfasst die Prüfung das Auffinden von Unvollkommenheiten, die vorwiegend parallel und/oder nach Vereinbarung rechtwinklig zur Schweißnaht verlaufen. Für elektrisch geschweißte oder induktionsgeschweißte (EW-) Stahlrohre umfasst die Prüfung das Auffinden der Unvollkommenheiten vorwiegend parallel zur Schweißnaht. Bei Prüfung auf Unvollkommenheiten in Längsrichtung darf nach Wahl des Herstellers mit Plattenwellen geprüft werden. Zum Nachweis der Unvollkommenheiten an der Schweißnaht bei EW-Rohren wird die Ultraschallprüfung über den gesamten Umfang akzeptiert. Dieses Dokument kann auch für die Prüfung von kreisförmigen Hohlprofilen angewendet werden. ANMERKUNG Ultraschallprüfungen über den gesamten Umfang für nahtlose und geschweißte (ausgenommen unterpulverschweißter) Rohre sind in der ISO 10893-10 festgelegt.
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons du cordon de soudure des tubes en acier soudés pour la détection des imperfections longitudinales et/ou transversales (ISO 10893-11:2011)
L'ISO 10893-11:2011 spécifie les exigences relatives au contrôle par ultrasons, avec ondes de cisaillement (générées par une technique conventionnelle ou la technique des réseaux à commande de phase), du cordon de soudure des tubes en acier soudés à l'arc immergé sous flux en poudre (SAW) ou des tubes en acier soudés par résistance électrique ou induction (EW).
Pour les tubes SAW, le contrôle couvre la détection des imperfections principalement orientées parallèlement et/ou, par accord, perpendiculairement au cordon de soudure.
Pour les tubes EW, le contrôle couvre la détection des imperfections principalement orientées parallèlement au cordon de soudure. Dans le cas de contrôle des imperfections longitudinales, un contrôle par ondes de Lamb peut être utilisé au choix du producteur.
L'ISO 10893-11:2011 est également applicable au contrôle des profils creux circulaires.
Neporušitveno preskušanje jeklenih cevi - 11. del: Avtomatizirano ultrazvočno preskušanje varjenega šiva varjenih jeklenih cevi za odkrivanje vzdolžnih in/ali prečnih nepopolnosti (ISO 10893-11:2011)
Ta del ISO 10893 določa zahteve za avtomatsko preiskavo vara jeklenih cevi, obločno varjenih pod praškom (SAW), ali električne upornosti in indukcijsko varjenih (EW) jeklenih cevi z ultrazvočnim strižnim valovanjem (ki nastane s konvencionalno tehniko ali tehniko faznih nizov). Za cevi SAW preskus zajema predvsem odkrivanje napak, usmerjenih vzporedno z varom ali po dogovoru pravokotno na var ali oboje. Za cevi EW preskus zajema predvsem odkrivanje napak, usmerjenih vzporedno z varom. Pri preskušanju vzdolžnih napak se po presoji proizvajalca lahko uporabi preskušanje z Lambovim valovanjem. Za odkrivanje napak na varu cevi EW je mogoča ultrazvočna preiskava po celotnem obodu. Ta del ISO 10893 lahko velja tudi za preskušanje krožnih votlih delov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10893-11:2011
01-november-2011
1DGRPHãþD
SIST EN 10246-8:2000
SIST EN 10246-9:2000
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYLGHO 8JRWDYOMDQMHY]GROåQLKLQDOL
SUHþQLKQDSDNYDUDSULMHNOHQLKFHYHKREORþQRYDUMHQLKSRGSUDãNRP]
DYWRPDWVNRXOWUD]YRþQRSUHLVNDYR ,62
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld
seam of welded steel tubes for the detection of longitudinal and/or transverse
imperfections (ISO 10893-11:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der
Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in Längs
- und/oder Querrichtung (ISO 10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons
du cordon de soudure des tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales (ISO 10893-11:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-11:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
25.160.40 Varjeni spoji in vari Welded joints
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-11:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-11:2011
EUROPEAN STANDARD
EN ISO 10893-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-8:1999, EN 10246-9:2000
English Version
Non-destructive testing of steel tubes - Part 11: Automated
ultrasonic testing of the weld seam of welded steel tubes for the
detection of longitudinal and/or transverse imperfections (ISO
10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Zerstörungsfreie Prüfung von Stahlrohren - Teil 11:
Contrôle automatisé par ultrasons du cordon de soudure Automatisierte Ultraschallprüfung der Schweißnaht
des tubes en acier soudés pour la détection des geschweißter Stahlrohre zum Nachweis von
imperfections longitudinales et/ou transversales (ISO Unvollkommenheiten in Längs- und/oder Querrichtung (ISO
10893-11:2011) 10893-11:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-11:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Foreword
This document (EN ISO 10893-11:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-8:1999, EN 10246-9:2000.
According
...
SLOVENSKI STANDARD
SIST EN ISO 10893-11:2011
01-november-2011
Nadomešča:
SIST EN 10246-8:2000
SIST EN 10246-9:2000
Neporušitveno preskušanje jeklenih cevi - 11. del: Avtomatizirano ultrazvočno
preskušanje varjenega šiva varjenih jeklenih cevi za odkrivanje vzdolžnih in/ali
prečnih nepopolnosti (ISO 10893-11:2011)
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld
seam of welded steel tubes for the detection of longitudinal and/or transverse
imperfections (ISO 10893-11:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der
Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in
Längs- und/oder Querrichtung (ISO 10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons
du cordon de soudure des tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales (ISO 10893-11:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-11:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
25.160.40 Varjeni spoji in vari Welded joints and welds
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-11:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-11:2011
EUROPEAN STANDARD
EN ISO 10893-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-8:1999, EN 10246-9:2000
English Version
Non-destructive testing of steel tubes - Part 11: Automated
ultrasonic testing of the weld seam of welded steel tubes for the
detection of longitudinal and/or transverse imperfections (ISO
10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Zerstörungsfreie Prüfung von Stahlrohren - Teil 11:
Contrôle automatisé par ultrasons du cordon de soudure Automatisierte Ultraschallprüfung der Schweißnaht
des tubes en acier soudés pour la détection des geschweißter Stahlrohre zum Nachweis von
imperfections longitudinales et/ou transversales (ISO Unvollkommenheiten in Längs- und/oder Querrichtung (ISO
10893-11:2011) 10893-11:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-11:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Foreword
This document (EN ISO 10893-11:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-8:1999, EN 10246-9:2000.
According
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.