EN 10021:2006
(Main)General technical delivery conditions for steel products
General technical delivery conditions for steel products
This European Standard specifies the general technical delivery conditions for all steel products covered by
EN 10079 with the exception of steel castings and powder metallurgical products.
Where the delivery requirements agreed for the order or specified in the appropriate product standard differ from the general technical delivery conditions defined in this European Standard, then the requirements agreed for the order or specified in the appropriate product standard apply.
NOTE Inspection documents are covered by EN 10168 and EN 10204.
Allgemeine technische Lieferbedingungen für Stahlerzeugnisse
Diese Europäische Norm beinhaltet die allgemeinen technischen Lieferbedingungen für alle in EN 10079 erfassten Stahlerzeugnisse mit Ausnahme von Stahlguss und pulvermetallurgischen Erzeugnissen.
Wenn die bei der Bestellung vereinbarten oder in den betreffenden Produktspezifikationen festgelegten Lieferbedingungen von den allgemeinen technischen Lieferbedingungen dieser Europäischen Norm abweichen, so gelten die Lieferbedingungen der Bestellung oder die der entsprechenden Produktspezifikation.
ANMERKUNG Prüfbescheinigungen werden in EN 10168 und EN 10204 behandelt.
Conditions générales techniques de livraison des produits en acier
Splošni tehnični dobavni pogoji za jeklene izdelke
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Allgemeine technische Lieferbedingungen für StahlerzeugnisseConditions générales techniques de livraison des produits en acierGeneral technical delivery conditions for steel products77.140.01Železni in jekleni izdelki na splošnoIron and steel products in generalICS:Ta slovenski standard je istoveten z:EN 10021:2006SIST EN 10021:2007en01-marec-2007SIST EN 10021:2007SLOVENSKI
STANDARDSIST EN 10021:19961DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10021December 2006ICS 77.140.01Supersedes EN 10021:1993
English VersionGeneral technical delivery conditions for steel productsConditions générales techniques de livraison des produitsen acierAllgemeine technische Lieferbedingungen fürStahlerzeugnisseThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10021:2006: ESIST EN 10021:2007
EN 10079:1992, EN 10204:2004 and the following apply. 3.1 cast (heat) analysis chemical analysis representative of the cast (heat) determined by the steelmaker at his discretion in a manner of his choice 3.2 inspection conformity evaluation by observation and judgment accompanied as appropriate by measurement, testing or gauging 3.3 inspection representative(s) one or more individual(s) who is/are either: a) the inspector(s) designated in any official regulation; b) the manufacturer’s authorized inspection representative(s), independent from the manufacturing department; c) the purchaser’s authorized inspection representative(s) SIST EN 10021:2007
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.