iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10359:2023

(Main)

Laser welded tailored blanks - Technical delivery conditions

Laser welded tailored blanks - Technical delivery conditions

This document specifies the requirements for laser welded tailored blanks (LWB) made of steels for all cold or hot forming processes.
This document is applicable to all steel grades with or without metallic and/or organic coatings, having uniform or different sheet thickness, welded with or without extra material addition.
After the welding process, LWB are further processed to pressed parts by forming operations under the responsibility of the processor.

Laserstrahlgeschweißte Tailored Blanks aus Stahlfeinblech - Technische Lieferbedingungen

Dieses Dokument legt die Anforderungen an lasergeschweißte Tailored Blanks (LWB) aus Stählen für alle Kalt- und Warmumformverfahren fest.
Dieses Dokument ist anwendbar für alle Stahlsorten mit oder ohne metallische und/oder organische Beschichtungen, mit gleichmäßiger oder unterschiedlicher Blechdicke, geschweißt mit oder ohne Zusatzwerkstoffzugabe.
Nach dem Schweißprozess werden LWB durch Umformprozesse unter der Verantwortung des Verarbeiters zu Pressteilen weiterverarbeitet.

Flans raboutés laser - Conditions techniques de livraison

Le présent document spécifie les exigences relatives aux flans raboutés laser (LWB) en acier pour tous les procédés de formage à froid ou à chaud.
Le présent document est applicable à toutes les nuances d'acier avec ou sans revêtements métalliques et/ou organiques, ayant une épaisseur de tôle uniforme ou différente, soudées avec ou sans ajout de matériau supplémentaire.
Après le processus de soudage, les LWB sont ensuite transformés en pièces embouties au moyen d’opérations de formage qui sont de la responsabilité du transformateur.

Lasersko varjeni posebej prilagojeni spoji - Tehnični dobavni pogoji

Ta dokument določa zahteve za lasersko varjene posebej prilagojene spoje (LWB) iz jekel za vse postopke hladnega ali vročega obdelovanja.
Uporablja se za vse razrede jekla s kovinskimi in/ali organskimi premazi ali brez njih, ki imajo enotno ali različno debelino pločevine, ter so varjeni z dodatnim materialom ali brez njega.
Po postopku varjenja se lasersko varjene posebej prilagojene spoje nadalje obdela v stisnjene dele s postopki oblikovanja, za katere je odgovoren obdelovalec.

General Information

Status
Published
Publication Date
02-May-2023
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
ECISS/TC 109 - Coated and uncoated flat products to be used for cold forming
Drafting Committee
ECISS/TC 109/WG 1 - Uncoated and coated flat products for cold forming and construction, except tin mill products
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
03-May-2023
Due Date
15-Feb-2024
Completion Date
03-May-2023
Ref Project
SIST EN 10359:2023 - Laser welded tailored blanks - Technical delivery conditions

Relations

Replaces
EN 10359:2015 - Laser welded tailored blanks - Technical delivery conditions
Effective Date
19-Jun-2019

Buy Standard

EN 10359:2023 - BARVEEN 10359:2023 - BARVE
PreviousNext
Standard
EN 10359:2023 - BARVE
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10359:2023
01-julij-2023
Lasersko varjeni posebej prilagojeni spoji - Tehnični dobavni pogoji
Laser welded tailored blanks - Technical delivery conditions
Laserstrahlgeschweißte Tailored Blanks aus Stahlfeinblech - Technische
Lieferbedingungen
Flans raboutés laser - Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10359:2023
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
SIST EN 10359:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 10359:2023

---------------------- Page: 2 ----------------------
SIST EN 10359:2023


EN 10359
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2023
EUROPÄISCHE NORM
ICS 77.140.50 Supersedes EN 10359:2015
English Version

Laser welded tailored blanks - Technical delivery
conditions
Flans raboutés laser - Conditions techniques de Laserstrahlgeschweißte Tailored Blanks aus
livraison Stahlfeinblech - Technische Lieferbedingungen
This European Standard was approved by CEN on 17 March 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10359:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 10359:2023
EN 10359:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 5
5 Tolerances on dimensions, shape and packaging . 5
6 Destructive testing of weld joints . 5
6.1 Cup test . 5
6.2 Cross section . 5
6.3 Heat treatment for hot stamped blanks . 5
6.4 Tensile testing for hot stamped blanks. 5
6.5 Hardness test for hot stamped blanks. 6
6.6 Tensile and hardness quality inspection interval for hot stamped LWB . 6
6.7 Cross section measurement method . 14
Annex A (normative) Tensile test failure assessment .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10209:2023(Main)
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
SIST EN 10209:2023

This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following:
-   cold-rolled low carbon steel flat products for cold forming (EN 10130);
-   cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold reduced blackplate (EN 10205);
-   steel sheet and strip for welded gas cylinders (EN 10120);
-   cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
-   cold-rolled structural steels for general purposes;
-   cold-rolled flat products made of high yield strength for cold forming (EN 10268).

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10169:2022(Main)
Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
SIST EN 10169:2022

This document specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
NOTE   National provisions can set up relationships between the performances of the coatings as required in this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
- tin mill products;
- electrical steels.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10202:2022(Main)
Cold reduced tinmill products - Electrolytic tinplate and electrolytic chromium/chromium oxide coated steel
SIST EN 10202:2022

This document specifies requirements for tinmill products in the form of sheets or coils. Tinmill products consist of single and double reduced low carbon mild steel electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS) or (ECCS-RC) (see 3.3).
Single reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,16 mm up to and including 0,49 mm. Double reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,12 mm up to and including 0,29 mm.
NOTE 1   Other thicknesses can be ordered upon agreement.
This document applies to coils and sheets cut from coils in nominal minimum widths of 600 mm.
NOTE 2   Standard width coils for specific uses, e.g. tabstock, can be slit into narrow strip for supply in coil form.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10372:2020(Main)
Quality tracking system for flat steel products using barcode - Printing, reading and information processing
SIST EN 10372:2020

This document specifies a method using a barcoding system for tracing isolated defects that can be present in the following kinds of coated or uncoated steel flat products, for example:
-   electro-galvanised surface;
-   galvanised surface;
-   galvannealed surface;
-   cold rolled surface.
This method, named "quality tracking", aims to transfer additional material information to steel users, in particular the location of some isolated defects, in a reliable way. This method enables the manufacturer or purchaser to remove blanks or coils containing defects.
The method uses a 1D barcode to identify each section of steel strip.
NOTE 1   The stakeholders most involved in this technique are suppliers of steel flat products, car makers, appliance makers, part manufacturers, blanking line builders, steel processors, service centres, etc. All stakeholders can benefit from this project since defects can be traced, and, therefore, the steel containing defects can be eliminated or set apart of the production line.
NOTE 2   In the first stages of development, this method was called "defect tracking" (see [3]) and has been changed into "quality tracking" at the beginning of the standardization process.    
NOTE 3   Quality tracking can be applied to other types of coated or uncoated steel flat products such as pickled and oiled, organic coated, and steels for packaging. Quality tracking can be applied for coiled materials for which the technology of quality tracking is applicable.
NOTE 4   If quality tracking data are used outside of the purpose of quality tracking, it is under the responsibility of the user.
NOTE 5   Quality tracking can be applied to other materials than steel.
NOTE 6   The way to collect the information to be transferred to the user is out of the scope of this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10139:2016+A1:2020(Main)
Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions
SIST EN 10139:2016+A1:2020

1.1   This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels in accordance with Table 1.
These products are suitable for cold forming. They are also suitable for surface coating. On the other hand, they are not suitable for hardening treatment followed by tempering.
1.2   This European Standard does not cover cold rolled flat products for which a separate standard already exists, particularly the following products:
-   cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10106);
-   grain-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10107);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold rolled narrow steel strip for heat treatment (EN 10132 1 to −4);
-   cold rolled steel flat products with higher yield strength for cold forming (EN 10268);
-   cold rolled low carbon steel flat products for cold forming (EN 10130);
-   cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel (EN 10205);
-   cold rolled low carbon steel flat products for vitreous enamelling (EN 10209).

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10152:2017(Main)
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
SIST EN 10152:2017

This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths above or equal to 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet.
NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of:
a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm),
b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g. 1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to prEN 10338, 3) steels for construction according to national or regional standards (see e. g. DIN 1623).
NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.).
NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10205:2016(Main)
Cold reduced tinmill products - Blackplate
SIST EN 10205:2017

This European Standard specifies requirements for blackplate product in the form of coils intended for direct use and mostly for the production of tinplate, electrolytically chromium / chromium oxide plate (ECCS) and electrolytically zinc coated plate.
Blackplate is specified in nominal thicknesses that are multiples of 0,005 mm from typical 0,10 mm up to 0,60mm.
This European Standard applies to coils in nominal minimum widths of 600 mm.
In addition to this standard the general technical delivery conditions of EN 10021 apply.
NOTE   Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10338:2015(Main)
Hot rolled and cold rolled non-coated products of multiphase steels for cold forming - Technical delivery conditions
SIST EN 10338:2015

This European Standard applies to hot rolled and cold rolled non-coated steel flat products made of multiphase steels for cold forming. It covers cold rolled products of thickness equal to or less than 3 mm and hot rolled products of thickness equal to or less than 6 mm.
These products are delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip.
Flat products of multiphase steels for cold forming may be delivered with an electrolytically zinc coating according to EN 10152.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10346:2015(Main)
Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
SIST EN 10346:2015

This European Standard specifies requirements for continuously hot-dip coated products made of low carbon steels for cold forming, of steels for construction, of steels with high proof strength for cold forming and coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ), aluminium-silicon alloy (AS) or zinc-magnesium alloy (ZM) and for continuously hot-dip coated products made of multiphase steels for cold forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA) or zinc-magnesium alloy (ZM) in thicknesses of 0,20 mm ≤ t < 3,0 mm.
By agreement at the time of enquiry and order, this European Standard is applicable to continuously hot-dip coated flat products of an expanded validity range defined for thicknesses t < 0,20mm or in thicknesses 3,0mm < t < 6,5mm with agreed mechanical properties and test specimens, adhesion of coating and surface condition requirements.
The thickness is the final thickness of the delivered product after coating.
This document applies to strip of all widths and to sheets cut from it (≥ 600 mm width) and cut lengths
(< 600 mm width).
NOTE 1   Products coated with (pure) aluminium can also be available, but are not covered by this European standard.
NOTE 2   The products covered by this European Standard are used where cold formability, high strength, a defined minimum yield strength and corrosion resistance are the most important factors. Corrosion resistance of the product is proportional to the coating thickness, hence to its mass (see also 7.3.2). The products covered by this European Standard can be used as substrates for organic coated flat products specified in EN 10169 for building and general engineering applications.
NOTE 3   By agreement at the time of enquiry and order, this European standard is applicable to other continuously hot-dip coated hot rolled steel flat products (e.g. in accordance with EN 10149-2).

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10268:2006+A1:2013(Main)
Cold rolled steel flat products with high yield strength for cold forming - Technical delivery conditions
SIST EN 10268:2006+A1:2014

This European Standard applies to cold rolled uncoated steel flat products for cold forming with high yield strength. The thickness is equal to or less than 3 mm.
These products are delivered in sheet, wide strip, slit wide strip, narrow strip or cut lengths obtained from slit wide strip, narrow strip or sheet.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day