iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13481-4:2002/A1:2006

(Amendment)

Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers

Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers

This European Standard is applicable to fastening systems for use on steel sleepers in ballasted track as follows:
¾ main lines having a radius of curvature greater than 150 m and subject to a maximum design axle load of 260 kN;
¾ light rail systems having a radius of curvature greater than 80 m and subject to a maximum design axle load of 130 kN.
The requirements apply to:
¾ direct fastening systems and systems which incorporate a baseplate;
¾ fastening systems for the rail sections in prEN 13674-1 and prEN 13674-4.
This standard is not applicable to fastening systems for other rail sections, rigid fastening systems or special fastening systems used at bolted joints.
This standard is for type approval of a complete fastening assembly only.

Bahnanwendungen - Oberbau - Leistungsanforderungen für Schienenbefestigungssysteme - Teil 4: Befestigungssysteme für Stahlschwellen

Ersetze prEN 13674-1 durch EN 13674-1 und prEN 13674-4 durch EN 13674-4.

Applications ferroviaires - Voie - Prescriptions de performance pour les systèmes de fixation - Partie 4: Systèmes de fixation des traverses en acier

Železniške naprave – Zgornji ustroj – Zahteve za izdelavo pritrdilnih sistemov – 4. del: Pritrdilni sistemi za jeklene prage

General Information

Status
Withdrawn
Publication Date
01-Aug-2006
Withdrawal Date
29-May-2012
ICS
93.100 - Construction of railways
Technical Committee
CEN/TC 256 - Railway applications
Drafting Committee
CEN/TC 256/SC 1/WG 17 - Fastening systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
30-May-2012
Completion Date
30-May-2012
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/024 - Mandate to CEN/CENELEC/ETSI for programming and standardization in the field of railway equipment
Ref Project
SIST EN 13481-4:2004/A1:2007 - Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers

Relations

Replaced By
EN 13481-4:2012 - Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers
Effective Date
06-Jun-2012
Amends
EN 13481-4:2002 - Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers
Effective Date
08-Jun-2022

Buy Standard

EN 13481-4:2004/A1:2007EN 13481-4:2004/A1:2007
PreviousNext
Amendment
EN 13481-4:2004/A1:2007
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2007
Železniške naprave – Zgornji ustroj – Zahteve za izdelavo pritrdilnih sistemov – 4.
del: Pritrdilni sistemi za jeklene prage
Railway applications - Track - Performance requirements for fastening systems - Part 4:
Fastening systems for steel sleepers
Bahnanwendungen - Oberbau - Leistungsanforderungen für
Schienenbefestigungssysteme - Teil 4: Befestigungssysteme für Stahlschwellen
Applications ferroviaires - Voie - Prescriptions de performance pour les systemes de
fixation - Partie 4: Systemes de fixation des traverses en acier
Ta slovenski standard je istoveten z: EN 13481-4:2002/A1:2006
ICS:
93.100 Gradnja železnic Construction of railways
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13481-4:2002/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2006
ICS 93.100
English Version
Railway applications - Track - Performance requirements for
fastening systems - Part 4: Fastening systems for steel sleepers
Applications ferroviaires - Voie - Prescriptions de Bahnanwendungen - Oberbau - Leistungsanforderungen für
performance pour les systèmes de fixation - Partie 4: Schienenbefestigungssysteme - Teil 4:
Systèmes de fixation des traverses en acier Befestigungssysteme für Stahlschwellen
This amendment A1 modifies the European Standard EN 13481-4:2002; it was approved by CEN on 26 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13481-4:2002/A1:2006: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
5.1 Longitudinal rail restraint.4
5.2 Torsional resistance.4
5.3 Effect of repeated loading.4
5.4 Electrical resistance of fastening system and sleeper.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17936:2024(Main)
Railway applications - Acoustics - Measurement of source terms for environmental noise calculations
SIST EN 17936:2024

This document addresses the measurement of source terms for environmental noise calculation for rail traffic (including light rail, such as trams, metros, etc.). It is applicable to the measurement of in-service trains on operational tracks.
It is not applicable to type acceptance testing of rolling-stock or tracks, or to derive source terms for time domain models.
The following rail traffic noise source types are in the scope:
-   rolling noise;
-   traction and equipment noise;
-   aerodynamic noise;
-   impact noise (e.g. rail joints, switch and crossings, wheel flats);
-   braking noise;
-   bridge noise;
-   squeal noise.
Noise from rail vehicles at standstill, such as stationary engine idling and auxiliary equipment at yards and stations, is covered by EN ISO 3095:2013 for measurement procedures and operating conditions, and by EN ISO 3740:2019 and EN ISO 3744 for the determination of sound power. It is therefore not in the scope of this document.
The calculation of the propagation of sound is part of generally standardized propagation models which are not addressed in this document.
Noise from fixed installations (e.g. stations, depots, electricity sub-stations) is not in the scope of this document.
Source terms are specific to a vehicle and track type. The scope includes measurement procedures and conditions and sampling requirements.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14587-2:2024(Main)
Railway applications - Infrastructure - Flash butt welding of new rails - Part 2: R200, R220, R260, R260Mn, R320Cr, R350HT, R350LHT, R370CrHT and R400HT grade rails by mobile welding machines at sites other than a fixed plant
SIST EN 14587-2:2024

This document specifies requirements for the approval of a welding process by mobile plant, together with the requirements for subsequent welding production.
It applies to new Vignole railway rails R200, R220, R260, R260Mn, R320Cr, R350HT, R350LHT, R370CrHT and R400HT grade rails of 46 kg/m and above, as contained in EN 13674-1:2011+A1:2017, welded by a flash butt welding process by mobile plant and intended for use on railway infrastructure.
This document applies to the welding of rails into welded strings.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16843:2024(Main)
Railway applications - Infrastructure - Mechanical requirements for joints in running rails
SIST EN 16843:2024

This European Standard deals with mechanical rail joints for flat bottom rails 46 kg/m and over. The scope of this standard is: to
establish requirements for insulated and non-insulated rail joints, for stressed rail (continuous welded rail, CWR) and unstressed rail (jointed track); to define mechanical and electrical requirements for type approval and for acceptance of insulated rail joints which are manufactured in a factory (prefab construction) as well as assembled onsite (site construction). This standard specifies the minimum requirements. Special applications as for instance tram systems may require different demands in certain paragraphs and should be agreed between customer and supplier. The scope also excludes expansion joints (it is covered in EN 13232-8), and special joints in switch constructions.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-5:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 5: Intrinsic characteristics - Sound absorption under direct sound field conditions
SIST EN 16272-5:2024

This document describes a test method for measuring a quantity representative of the intrinsic characteristics of sound absorption from railway noise barriers and related devices acting on airborne sound propagation, the sound reflection index RI, and then calculate a single-number rating for sound absorption from it.
The test method is intended for the following applications:
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed along railways, to be measured either on typical installations alongside railways or on a relevant sample section;
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation in actual use under direct sound field conditions;
-   comparison of design specifications with actual performance data after the completion of the construction work;
-   verification of the long-term performance of noise barriers and related devices acting on airborne sound propagation (with a repeated application of the method).
The test method is not intended for the following applications:
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed in reverberant conditions, e.g. inside tunnels or deep trenches.
Results for the sound reflection index are expressed as a function of frequency, in one-third octave bands, where possible, between 100 Hz and 5 kHz. If it is not possible to get valid measurements results over the whole frequency range indicated, the results are given in a restricted frequency range and the reasons of the restriction(s) are clearly reported.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-1:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 1: Intrinsic characteristics - Sound absorption under diffuse sound field conditions
SIST EN 16272-1:2024

This European Standard specifies the laboratory method for measuring the sound absorption performance of railway noise barriers and related devices acting on airborne sound propagation in reverberant conditions. It covers the assessment of the intrinsic sound absorption performance of devices that can reasonably be assembled inside the testing facility described in EN ISO 354.
This method is not intended for the determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed on railways in non-reverberant conditions.
The test method in EN ISO 354 referred to in this European Standard excludes devices that act as weakly damped resonators. Some devices will depart significantly from these requirements and in these cases, care is needed in interpreting the results.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-2:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 2: Intrinsic characteristics - Airborne sound insulation under diffuse sound field conditions
SIST EN 16272-2:2024

This document specifies the laboratory method for measuring the airborne sound insulation performance of railway noise barriers in reverberant conditions. It covers the assessment of the intrinsic performance of noise barriers and related devices acting on airborne sound propagation that can reasonably be assembled inside the testing facility described in EN ISO 10140 2 and EN ISO 10140 4.
This method is not intended for the determination of the intrinsic characteristics of airborne sound insulation of noise barriers to be installed on railway in non-reverberant conditions.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices, are out of the scope of this document.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-6:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 6: Intrinsic characteristics - Airborne sound insulation under direct sound field conditions
SIST EN 16272-6:2024

This document describes a test method for measuring a quantity representative of the intrinsic characteristics of airborne sound insulation for rail noise barriers and related devices: the sound insulation index.
The test method is intended for the following applications:
-   determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed along railways, to be measured either on typical installations alongside railways or in laboratory conditions;
-   determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices in actual use;
-   comparison of design specifications with actual performance data after the completion of the construction work;
-   verification of the long-term performance of noise barriers and related devices (with a repeated application of the method);
-   interactive design process of new products, including the formulation of installation manuals.
The test method is not intended for the determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed in reverberant conditions, e.g. inside tunnels or deep trenches or under covers.
Results are expressed as a function of frequency in one-third octave bands, where possible, between 100 Hz and 5 kHz. If it is not possible to get valid measurement results over the whole frequency range indicated, the results need to be given in a restricted frequency range and the reasons for the restriction(s) need to be clearly reported.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13231-1:2023(Main)
Railway applications - Track - Acceptance of works - Part 1: Works on ballasted track - Plain line, switches and crossings
SIST EN 13231-1:2024

This document specifies technical requirements and tolerances for the acceptance of works on ballasted track situated on:
-   plain line;
-   switches and crossings; and
-   rail expansion devices as part of the track
for 1 435 mm and wider track gauge railways.
The works on ballasted track, hereafter referred to as track works, concern construction of new track, track renewal and track maintenance.
This document specifies the requirements for substructure works, track geometry, absolute track position, working parameters of on track machines, track components, ballast cross section, structure gauge, stressing works, specific measurements and quality checks for switches and crossings and rail expansion devices, and for the measuring systems used to perform measurements, verifications and checks for the scope of acceptance. Requirements for responsibilities and documentation necessary for the acceptance of track works are specified.
This document also requires compliance of all track materials with the customer’s relevant acceptance criteria and specifications provided by the supplier.
This document does not cover works related to reprofiling the railhead or the associated measurements, except for some measurements related to safety, as these works are covered by other parts of EN 13231 series.
Platform reconstruction works and level crossing works are not covered by this document.
This document does not apply to urban rail systems or ballastless track.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-3-1:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-1: Normalized railway noise spectrum and single number ratings for diffuse sound field applications
SIST EN 16272-3-1:2023

This document specifies a normalized railway noise spectrum for the evaluation and assessment of the acoustic performance of devices designed to reduce airborne railway noise near railways.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices are outside of the scope of this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-3-2:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-2: Normalized railway noise spectrum and single number ratings for direct sound field applications
SIST EN 16272-3-2:2023

This document specifies a normalized railway noise spectrum for the evaluation and assessment of the acoustic performance of devices designed to reduce airborne railway noise near railways.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices are outside of the scope of this document.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day