EN 12167:2011

Copper and copper alloys - Profiles and bars for general purposes

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen Verwendung

Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Profile, einschließlich mit L-, T- und U-förmigen Querschnitten und Rechteckstangen aus Kupferlegierungen fest. Diese Europäische Norm gilt für Profile mit L-, T- und U-förmigen Querschnitten mit einem Durchmesser des umschreibenden Kreises von höchstens 180 mm und Rechteckstangen mit Dicken von 3 mm bis 60 mm und Breiten von 6 mm bis 120 mm. Der Ablauf der Probenentnahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm sind ebenfalls festgelegt.

Cuivre et alliages de cuivre - Profilés et barres pour usages généraux

La présente Norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des profilés en alliage de cuivre, incluant les sections en L, T, U et les barres, fabriqués par étirage ou filage.
La présente Norme européenne s’applique aux profilés avec section en L, T et U adaptés à un cercle circonscrit d’un diamètre maximal de 180 mm, et aux barres d’épaisseur comprise entre 3 mm et 60 mm inclus et de largeur comprise entre 6 mm et 120 mm inclus.
Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente Norme européenne sont également spécifiées.

Baker in bakrove zlitine - Profili in palice za splošno uporabo

Dokument določa sestavo, zahteve za lastnosti in odstopke mer za ravne profile in pravokotne palice iz bakra in bakrovih zlitin. Velja za pravokotne palice debeline od 3 mm do vključno 60 mm in širine od 6 mm do vključno 20 mm. Določeni so tudi postopki vzorčenja in metode preskušanja za preverjanje skladnosti z zahtevami tega dokumenta.

General Information

• Status: Withdrawn
• Publication Date: 31-May-2011
• Withdrawal Date: 19-Jul-2016
• ICS: 77.150.30 - Copper products
• Technical Committee: CEN/TC 133 - Copper and copper alloys
• Drafting Committee: CEN/TC 133/WG 4 - Extruded and drawn products, forgings and scrap
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 20-Jul-2016
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Ref Project: SIST EN 12167:2011 - Copper and copper alloys - Profiles and bars for general purposes

Relations

• Replaces: EN 12167:1998 - Copper and copper alloys - Profiles and rectangular bar for general purposes
• Effective Date: 28-May-2011
• Replaced By: EN 12167:2016 - Copper and copper alloys - Profiles and bars for general purposes
• Effective Date: 27-Jul-2016

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Profili in palice za splošno uporaboKupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen VerwendungCuivre et alliages de cuivre - Profilés et barres pour usages générauxCopper and copper alloys - Profiles and bars for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12167:2011SIST EN 12167:2011en,fr,de01-oktober-2011SIST EN 12167:2011SLOVENSKI
STANDARDSIST EN 12167:19991DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12167
June 2011 ICS 77.150.30 Supersedes EN 12167:1998English Version
Copper and copper alloys - Profiles and bars for general purposes
Cuivre et alliages de cuivre - Profilés et barres pour usages généraux
Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen Verwendung This European Standard was approved by CEN on 14 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12167:2011: ESIST EN 12167:2011

Determination of mean depth of dezincification . 40A.1Introduction . 40A.2Procedure . 40A.3Expression of results . 40Bibliography . 42 Tables Table 1 — Composition of low alloyed copper alloys . 19 Table 2 — Composition of copper-aluminium alloys . 20 Table 3 — Composition of copper-nickel-zinc alloys . 20 Table 4 — Composition of copper-tin alloys . 21 Table 5 — Composition of copper-zinc alloys. 21 Table 6 — Composition of copper-zinc-lead alloys . 22 Table 7 — Composition of complex copper-zinc alloys . 24 Table 8 — Mechanical properties of low alloyed copper alloys . 25 Table 9 — Mechanical properties of copper-aluminium alloys . 27 Table 10 — Mechanical properties of copper-nickel-zinc alloys . 28 Table 11 — Mechanical properties of copper-tin alloys . 29 Table 12 — Mechanical properties of copper-zinc alloys . 30 Table 13 — Mechanical properties of copper-zinc-lead alloys . 31 Table 14 — Mechanical properties of complex copper-zinc alloys . 33 Table 15 — Tolerances on width (b) and height of a leg (h) for profiles with L-, T- and U-cross-sections . 35 Table 16 — Tolerances on thickness for profiles with L-, T- and U-cross-sections. 36 Table 17 — Tolerances on width and thickness of bar . 37 Table 18 — Tolerances on length of bar . 37 Table 19 — Tolerances on straightness of bar, for widths 10 mm and over . 38 Table 20 — Maximum twist of bar . 38 Table 21 — Corner radii of bar . 38 Table 22 — Sampling rate . 39
Figures Figure 1 — Measurement of flatness of bar . 13 Figure 2 — Measurement of twist of bar . 14 Figure A.1 — Example of contiguous fields . 41
...