EN ISO 19403-1:2022
(Main)Paints and varnishes - Wettability - Part 1: Vocabulary and general principles (ISO 19403-1:2022)
Paints and varnishes - Wettability - Part 1: Vocabulary and general principles (ISO 19403-1:2022)
This document specifies general terms and definitions for wettability. Some general principles are described in Annex A. This document is intended to be used in conjunction with ISO 4618.
Beschichtungsstoffe - Benetzbarkeit - Teil 1: Begriffe und allgemeine Grundlagen (ISO 19403-1:2022)
Dieses Dokument legt allgemeine Begriffe zur Benetzbarkeit fest. Einige allgemeine Grundlagen sind im Anhang A erläutert. Dieses Dokument ist zur Verwendung in Verbindung mit ISO 4618 vorgesehen.
Peintures et vernis - Mouillabilité - Partie 1: Vocabulaire et principes généraux (ISO 19403-1:2022)
Le présent document spécifie les termes et définitions génériques relatifs à la mouillabilité. Quelques principes généraux sont décrits à l’Annexe A. Le présent document est destiné à être utilisé conjointement avec l'ISO 4618.
Barve in laki - Omočljivost - 1. del: Terminologija in splošna načela (ISO 19403-1:2022)
Ta dokument določa splošne izraze in definicije za omočljivost. Nekatera splošna načela so opisana v dodatku A. Ta dokument je treba uporabljati v povezavi s standardom ISO 4618.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN ISO 19403-1:2020
Barve in laki - Omočljivost - 1. del: Terminologija in splošna načela (ISO 19403-
1:2022)
Paints and varnishes - Wettability - Part 1: Vocabulary and general principles (ISO 19403
-1:2022)
Beschichtungsstoffe - Benetzbarkeit - Teil 1: Begriffe und allgemeine Grundlagen (ISO
19403-1:2022)
Peintures et vernis - Mouillabilité - Partie 1: Vocabulaire et principes généraux (ISO
19403-1:2022)
Ta slovenski standard je istoveten z: EN ISO 19403-1:2022
ICS:
01.040.87 Industrija barv (Slovarji) Paint and colour industries
(Vocabularies)
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 19403-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 01.040.87; 87.040 Supersedes EN ISO 19403-1:2020
English Version
Paints and varnishes - Wettability - Part 1: Vocabulary and
general principles (ISO 19403-1:2022)
Peintures et vernis - Mouillabilité - Partie 1: Beschichtungsstoffe - Benetzbarkeit - Teil 1: Begriffe
Vocabulaire et principes généraux (ISO 19403-1:2022) und allgemeine Grundlagen (ISO 19403-1:2022)
This European Standard was approved by CEN on 5 June 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19403-1:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 19403-1:2022) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2022, and conflicting national standards
shall be withdrawn at the latest by December 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19403-1:2020.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19403-1:2022 has been approved by CEN as EN ISO 19403-1:2022 without any
modification.
INTERNATIONAL ISO
STANDARD 19403-1
Second edition
2022-06
Paints and varnishes — Wettability —
Part 1:
Vocabulary and general principles
Peintures et vernis — Mouillabilité —
Partie 1: Vocabulaire et principes généraux
Reference number
ISO 19403-1:2022(E)
ISO 19403-1:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 19403-1:2022(E)
Contents Page
Foreword .iv
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Terms relating to determination of the surface free energy . 1
3.2 Terms relating to determination of the surface tension of liquids . 3
3.3 Terms relating to wetting . 4
Annex A (informative) General principles . 6
Bibliography .11
iii
ISO 19403-1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 19403-1:2017), which has been technically
revised.
The main changes are as follows:
— in the title, "Terminology" has been changed to "Vocabulary";
— text from the Scope has been moved to the Introduction;
— 3.1.5, 3.1.7, 3.1.8 and 3.1.9 have been slightly modified;
— the following terms and definitions have been added: hydrophobic, superhydrophobic, hydrophilic,
superhydrophilic and superhydrophobic coating;
— Clause 4 has been moved to Annex A;
— Figure 1 and Figure A.1 have been updated;
— the designation of the X-axis in Figure A.2 has been corrected;
— the derivation of Formula (A.4) has been improved;
— Formula (A.6) has been corrected;
— bibliographic entries [1] and [12] have been added and cross-references updated.
A list of all parts in the ISO 19403 series can be found on the ISO website.
iv
ISO 19403-1:2022(E)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
ISO 19403-1:2022(E)
vi
ISO 19403-1:2022(E)
Introduction
The ISO 19403 series specifies optical test methods:
— for the measurement of the contact angle;
— for the determination of the surface free energy of a solid surface, including the polar and dispersive
fractions;
— for the determination of the surface tension of liquids, including the polar and dispersive fractions;
— for the checking of the measurement arrangement with reference materials.
The ISO 19403 series can be applied for the characterization of substrates, coatings and coating
materials.
[4]
The applicability can be restricted for liquids with non-Newtonian flow behaviour (see DIN 1342-1 ).
vii
INTERNATIONAL STANDARD ISO 19403-1:2022(E)
Paints and varnishes — Wettability —
Part 1:
Vocabulary and general principles
1 Scope
This document specifies general terms and definitions for wettability. Some general principles are
described in Annex A. This document is intended to be used in conjunction with ISO 4618.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1 Terms relating to determination of the surface free energy
3.1.1
chemical homogeneity
chemically homogeneous composition of a surface to be examined
Note 1 to entry: The definition regards a purely qualitative assessment of the surface. Regarding the
measurement of the contact angle, a surface is considered chemically and topologically sufficiently homogeneous
if no significant differences of the contact angles can be determined when measuring on several locations on the
surface. The significance limits can be specified by the user in accordance with standard laboratory methods.
3.1.2
topological homogeneity
uniformity of the macroscopic surface, including evenness and smoothness
Note 1 to entry: The definition regards a purely qualitative assessment of the surface. Regarding the
measurement of the contact angle, a surface is considered chemically and topologically sufficiently homogeneous
if no significant differences of the contact angles can be determined when measuring on several locations on the
surface. The significance limits can be specified by the user in accordance with standard laboratory methods.
3.1.3
interfacial free energy
interfacial tension
σ
energy or tension resulting from intermolecular forces on interfaces
Note 1 to entry: The term interfacial energy pertains to the interaction with solid sur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.