CEN/TR 15868:2009
(Main)Survey of national requirements used in conjunction with EN 206-1:2000
Survey of national requirements used in conjunction with EN 206-1:2000
This CEN Report provides a summary of national requirements used with EN 206-1:2000. The aims of this
CEN Report are to:
a) provide a picture of how EN 206-1 is being applied in practice;
b) identify areas where EN 206-1 is being interpreted in different ways;
c) identify areas where CEN Member Countries have found simplification to be necessary;
d) identify additional national requirements;
e) show areas where CEN Member Countries have found it necessary to override the requirements of
EN 206-1.
EN 206-1 uses the phrase ‘national provisions’. However, recent CEN Guidance wishes to retain this term for
regulatory requirements only. This survey uses the term ‘national requirements’ to include regulations,
standards and other documents that form the basis of local practice.
As a summary of national requirements, the information in this CEN Report is incomplete and may have been
subject to later revisons. It is insufficient and not intended to provide the basis for design and specification: for
this the national requirements (see Table 1.1) should be studied.
Table 1.1 identifies CEN Member Countries who did not respond to the questionnaire. The other tables in this
CEN Report only include information from CEN Member Countries who responded and CEN Member
Countries who did not respond are not identified.
Überblick nationaler Anforderungen, die im Zusammenhang mit EN 206-1:2000 verwendet werden
État des prescriptions nationales utilisées avec l'EN 206-1:2000
Pregled nacionalnih zahtev, ki se uporabljajo skupaj z EN 206-1:2000
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2009
Pregled nacionalnih zahtev, ki se uporabljajo skupaj z EN 206-1:2000
Survey of national requirements used in conjunction with EN 206-1:2000
Überblick nationaler Anforderungen, die im Zusammenhang mit EN 206-1:2000
verwendet werden
État des prescriptions nationales utilisées avec l'EN 206-1:2000
Ta slovenski standard je istoveten z: CEN/TR 15868:2009
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL REPORT
CEN/TR 15868
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
June 2009
ICS 91.100.30
English Version
Survey of national requirements used in conjunction with EN
206-1:2000
État des prescriptions nationales utilisées avec l'EN 206- Überblick nationaler Anforderungen, die im
1:2000 Zusammenhang mit EN 206-1:2000 verwendet werden
This Technical Report was approved by CEN on 3 February 2009. It has been drawn up by the Technical Committee CEN/TC 104.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 15868:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Scope .4
2 Location of national requirements .6
3 Exposure classes.8
4 Constituent materials . 27
5 Limiting values . 35
6 Methods for minimising the risk of damaging ASR . 57
7 Use of additions . 62
8 Intermediate compressive strength classes . 75
9 Conformity and certification . 76
10 National provisions related to additional or different requirements . 84
11 Production control . 96
Annex A National minimum aggregate categories for normal weight aggregate concrete used in
general construction . 99
Annex B Limiting values . 117
Annex C Use of Ground Granulated Blastfurnace Slag . 135
Foreword
This document (CEN/TR 15868:2009) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
1 Scope
This CEN Report provides a summary of national requirements used with EN 206-1:2000. The aims of this
CEN Report are to:
a) provide a picture of how EN 206-1 is being applied in practice;
b) identify areas where EN 206-1 is being interpreted in different ways;
c) identify areas where CEN Member Countries have found simplification to be necessary;
d) identify additional national requirements;
e) show areas where CEN Member Countries have found it necessary to override the requirements of
EN 206-1.
EN 206-1 uses the phrase ‘national provisions’. However, recent CEN Guidance wishes to retain this term for
regulatory requirements only. This survey uses the term ‘national requirements’ to include regulations,
standards and other documents that form the basis of local practice.
As a summary of national requirements, the information in this CEN Report is incomplete and may have been
subject to later revisons. It is insufficient and not intended to provide the basis for design and specification: for
this the national requirements (see Table 1.1) should be studied.
Table 1.1 identifies CEN Member Countries who did not respond to the questionnaire. The other tables in this
CEN Report only include information from CEN Member Countries who responded and CEN Member
Countries who did not respond are not identified.
Members of Ad Hoc Group
Professor Tom Harrison, Convenor Dr. Ir. Hans Cornelissen
Dipl.-Ing. Anette Berrig Dr. Michel Delort
Dr. Ir. Claude Bleiman Dr. John Moore
Dr. Manuel Burόn Dipl.-Ing. Udo Wiens
CEN Member Countries CEN Member Countries
Austria AT Latvia LV
Belgium BE Lithuania LT
Cyprus CY Luxembourg LU
Czech Republic CZ Malta MT
Denmark DK Netherlands NL
Estonia EE Norway NO
Finland FI Poland PL
France FR Portugal PT
Germany DE Slovakia (Slovak Republic) SK
Greece GR Slovenia SI
Hungary HU Spain ES
Iceland IS Sweden SE
Ireland IE Switzerland CH
Italy IT United Kingdom UK
Affiliates
Albania AL
Bulgaria BG
Croatia (Hrvatska) HR
Romania RO
Turkey TR
2 Location of national requirements
Table 1.1 gives the title of the documents that contain the national requirements, together with an English
translation of the title. Any person wishing to design and specify concrete in another CEN Member Country
should consult the documents cited in Table 1.1. Please note that the documents will be written in the national
language(s) of the CEN Member Country. It should also be noted that the survey was conducted during 2005
to 2006 and the answers reflect practice at that time, which may not be the same as current practice.
Table 1.1 — Location of national requirements
CEN Member
Location of national requirements
a
Countries
Austria ÖNORM B 4710-1: Beton — Teil 1: Festlegung, Herstellung, Verwendung und
Konformitätsnachweis (Regeln zur Umsetzung der ÖNORM EN 206-1)
(Concrete — Part 1: Specification, production, use and verification of conformity (Rules for
the implementation of ÖNORM EN 206-1))
Belgium NBN B 15-001: Supplément à la NBN EN 206-1 — Béton — Spécification, performances,
production et conformité
NBN B 15-001: Aanvulling op NBN EN 206-1 — Beton — Eisen, gedraging, vervaardiging
en conformiteit (Supplement to NBN EN 206-1: Concrete — Specification, performance,
production and conformity)
Cyprus No response received
Czech Republic CSN EN 206-1 Zmena Z2
Denmark DS 2426: Beton — Materialer — Regler for anvendelse af EN 206-1 i Danmark
(Concrete — Materials — Rules for the use of EN 206-1 in Denmark)
Estonia No response received
Finland Suomen rakentamismääräyskokoelma, B4 Betonirakenteet, Liite 3: Kansallinen liite
standardiin SFS-EN 206-1 (National Building Code of Finland, B4 Concrete structures,
Annex 3: national Annex to standard SFS-EN 206-1)
Informative Guidance document: Betoninormit 2004, Suomen Betoniyhdistys
(Concrete Code, Finnish Concrete Association)
France National annex included in the NF EN 206-1 standard
Germany DIN 1045-2: Tragwerke aus Beton, Stahlbeton und Spannbeton — Teil 2: Beton —
Festlegung, Eigenschaften, Herstellung und Konformität — Anwendungsregeln zu
DIN EN 206-1
(DIN 1045-2: Concrete, reinforced and prestressed concrete structures — Part 2:
Concrete — Specification, properties, production and conformity — Application rules for
DIN EN 206-1)
Greece No response received
Hungary No response received
Iceland No response received
Ireland National Annex; published with I.S. EN 206-1 as a single document.
Italy UNI 11104: Calcestruzzo — Specificazione, prestazione produzione e conformità Istruzioni
complementari per l’applicazione della EN 206-1
(Concrete — Specification, performance, production and conformity, Additional provisions
for the application of EN 206-1)
Table 1.1 (continued)
CEN Member
Location of national requirements
a
Countries
Latvia No response received
Lithuania No response received
Luxembourg DNA EN 206: Document National d’Application luxembourgeois de l’EN 206-1: Béton —
Partie 1: Spécification, performances, production et conformité
(DNA EN 206: Luxemburgish national application document of the EN 206-1: Concrete —
Part 1: specification, performance, production and conformity)
Malta There are no national provisions, but in the past, local industry has used recommendations
in European, British or German standards
Netherlands NEN 8005:2004: Nederlandse invulling van NEN-EN 206-1: Beton — Deel 1: Specificatie,
eigenschappen, vervaardiging en conformiteit
(Dutch supplement to NEN-EN 206-1: Concrete — Part 1: Specification, performance,
production and conformity)
Norway NS-EN 206-1 National Annex
Poland No response received
Portugal The Portuguese requirements are in the National Annex to NP EN 206-1 and to
NP ENV 13670-1 and in the following National Civil Engineering Laboratory (LNEC)
specifications, referenced in the NA of NP EN 206-1
LNEC E 461:2004: Metodologia para prevenir reacções expansivas internas (Methodology
for avoiding internal expansive reactions)
LNEC E 464:2005: Metodologia prescritiva para uma vida útil de 50 e 100 anos face às
acções ambientais
(Prescritive methodology for a 50 and 100 years design working life under the
environmental exposures)
LNEC E 465:2005: Metodologia para estimar as propriedades de desempenho do betão
que permitam satisfazer a vida útil de projecto de estruturas de betão armado ou
pré-esforçado sob as exposições ambientais XC e XS (Methodology for estimating the
concrete performance properties allowing to comply with the design working life of the
reinforced or prestressed concrete structures under the environmental exposures XC and
XS)
Slovakia STN EN 206-1: Zmena 1 Concrete — Part 1: Specification, performance, production and
conformity supplements EN 206-1 with the national provisions
STN 731210: Water-proof concrete and concrete types of the specific characteristics
(Resistance to abrasion, Concrete for the massive constructions — Low hydrating warmth)
Slovenia SIST 1026: Beton — 1.del: Specifikacija, lastnosti, proizvodnja in skladnost — Pravila za
uporabo SIST EN 206-1
(SIST 1026: Concrete — Part 1: Specification, performance, production and conformity—
Rules for the implementation of SIST EN 206-1)
Spain Spain has not adopted EN 206-1
Sweden SS 13 70 03: Betong – Användning av EN 206-1 I Sverige
(Concrete — Application of EN 206-1 in Sweden)
Vägledning för val av exponeringsklass enligt SS-EN 206-1, Betongrapport nr 11, Svenska
Betongföreningen (Guidance for selection of exposure class according to SS-EN 206-1,
Concrete report No 11, Swedish Concrete Association)
Table 1.1 (continued)
CEN Member
Location of national requirements
a
Countries
Switzerland SN EN 206-1:2000: Beton — Teil 1: Festlegung, Eigenschaften, Herstellung und
Konformität (mit Nationalem Vorwort und Nationalem Anhang)
(SN-EN 206-1:2000: Concrete — Part 1: Specification, performance, production and
conformity (with National Preface and National Annex))
SN EN 206-1:2000/A1:2004: Beton — Teil 1: Festlegung, Eigenschaften, Herstellung und
Konformität
(SN EN 206-1:2000/A2:2005: Concrete — Part 1: Specification, performance, production
and conformity)
Ergänzung zum Nationalen Anhang NB der Norm SN EN 206-1:2000: Teil 1: Verwendung
von Zementen und Zusatzstoffen gemäss dem Prinzip der gleichwertigen
Betonleistungsfähigkeit (in Arbeit)
(Amendments to the National Annex of the SN EN 206-1: Part 1: Use of cements and
mineral additions according to the equivalent performance concept of concrete properties
(in preparation))
Ergänzung zum Nationalen Anhang der Norm SN EN 206-1:2000: Teil 1: Anwendung des
k-Wert Konzeptes gemäss dem Prinzip der gleichwertigen Betonleistungsfähigkeit (in
Arbeit); der Anhang wird Nationaler Anhang NC genannt (Application of the k-value
concept according to the principle of the equivalent concrete performance)
United Kingdom BS 8500: Concrete — Complementary British Standard to BS EN 206-1
— Part 1: Method of specifying and guidance for the specifier
— Part 2: Specification for constituent materials and concrete
a
None of the CEN affiliates chose to respond to this survey.
3 Exposure classes
In Table 2.1 exposure classes that have been grouped together are given. A significant number of
CEN Member Countries have found the need to simplify the system. In its simplest form this reduces to
interior, outside, severe and (chemically) aggressive. A significant number of CEN Member Countries have
grouped classes (not always in the same way). For example, XC3 and XC4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.