EN 12168:2016
(Main)Copper and copper alloys - Hollow rod for free machining purposes
Copper and copper alloys - Hollow rod for free machining purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.
Kupfer und Kupferlegierungen - Hohlstangen für die spanende Bearbeitung
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Hohlstangen aus Kupferlegierungen für die spanende Bearbeitung fest.
ANMERKUNG Hohlstangen mit einem Außendurchmesser über 80 mm und/oder einer Wanddicke unter 2 mm sind in EN 12449 festgelegt.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm sind ebenfalls festgelegt.
Cuivre et alliages de cuivre — Barres creuses pour décolletage
La présente Norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des barres creuses en alliage de cuivre fabriquées par étirage ou filage, particulièrement conçues pour le décolletage.
NOTE Les produits creux de diamètre extérieur supérieur à 80 mm et/ou ayant une épaisseur de paroi inférieure à 2 mm sont traités dans l'EN 12449.
Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente Norme européenne sont également spécifiées.
Baker in bakrove zlitine - Votle palice za obdelavo z odrezovanjem na avtomatih
Ta evropski standard določa sestavo, zahteve glede značilnosti in odstopanja glede mer za votle palice iz bakrovih zlitin, končno izdelane z vlečenjem ali ekstrudiranjem, zlasti namenjene za obdelavo z odrezovanjem na avtomatih.
OPOMBA: Votli proizvodi z zunanjim premerom, večjim od 80 mm, in/ali debelino stene manj kot 2 mm so opredeljeni v standardu EN 12449.
Določeni so tudi postopki vzorčenja in preskusne metode za preverjanje skladnosti z zahtevami tega evropskega standarda.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Votle palice za obdelavo z odrezovanjem na avtomatihKupfer und Kupferlegierungen - Hohlstangen für die spanende BearbeitungCuivre et alliages de cuivre — Barres creuses pour décolletageCopper and copper alloys - Hollow rod for free machining purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12168:2016SIST EN 12168:2016en,fr,de01-oktober-2016SIST EN 12168:2016SLOVENSKI
STANDARDSIST EN 12168:20111DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12168
July
t r s x ICS
y yä s w rä u r Supersedes EN
s t s x zã t r s sEnglish Version
Copper and copper alloys æ Hollow rod for free machining purposes Cuivre et alliages de cuivre æ Barres creuses pour décolletage
Kupfer und Kupferlegierungen æ Hohlstangen für die spanende Bearbeitung This European Standard was approved by CEN on
{ April
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t s x zã t r s x ESIST EN 12168:2016
Figures Figure 1 — Examples of hollow rod cross-sections .8 Figure 2 — Measurement of twist of polygonal hollow rod . 17
Tables Table 1 — Composition of low alloyed copper alloys . 21 Table 2 — Composition of copper-zinc alloys. 22 Table 3 — Composition of copper-zinc-lead alloys . 23 Table 4 — Composition of complex copper-zinc alloys . 26 Table 5 — Mechanical properties of low alloyed copper alloys . 27 Table 6 — Mechanical properties of copper-zinc alloys . 28 Table 7 — Mechanical properties of copper-zinc-lead alloys . 31 Table 8 — Mechanical properties of complex copper-zinc alloys . 34 Table 9 — Tolerances on external diameter or width across-flats. 38 Table 10 — Tolerances on wall thickness . 38 Table 11 — Tolerances on diameter of the bore . 38 Table 12 — Tolerances on eccentricity . 39 Table 13 — Tolerances on straightness of hollow rod . 39 Table 14 — Tolerances on length of hollow rod . 39 Table 15 — Corner radii for hollow rod with square, hexagonal or octagonal external shape . 39 Table 16 — Maximum twist for hollow rod with square, hexagonal or octagonal external shape . 40 Table 17 — Sampling rate . 40 SIST EN 12168:2016
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.