EN ISO 10088:2017
(Main)Small craft - Permanently installed fuel systems (ISO 10088:2013)
Small craft - Permanently installed fuel systems (ISO 10088:2013)
ISO 10088:2013 specifies the requirements for the design, materials, construction, installation and testing of permanently installed fuel systems as installed for internal combustion engines.
It applies to all parts of permanently installed diesel and petrol fuel systems as installed, from the fuel fill opening to the point of connection with the propulsion or auxiliary engine(s) on inboard- and outboard-powered small craft of up to 24 m hull length.
Requirements for the design, materials, construction and testing of permanently installed fixed fuel tanks are given in ISO 21487.
Kleine Wasserfahrzeuge - Dauerhaft installierte Kraftstoffsysteme (ISO 10088:2013)
Petits navires - Systèmes à carburant installés à demeure (ISO 10088:2013)
L'ISO 10088:2013 spécifie les exigences concernant la conception, les matériaux, la construction, l'installation et les essais des systèmes à carburant installés à demeure et destinés à l'alimentation des moteurs à combustion interne.
Elle s'applique à tous les éléments des systèmes à carburant diesel et essence installés à demeure, depuis le nable de remplissage jusqu'au point de raccordement au(x) moteur(s) de propulsion ou au(x) moteur(s) auxiliaire(s) des petits navires propulsés par un ou des moteurs intérieurs ou hors-bord, et de longueur de coque inférieure ou égale à 24 m.
Les exigences concernant la conception, les matériaux, la construction et les essais des réservoirs fixes à carburant installés à demeure sont données dans l'ISO 21487.
Mala plovila - Trajno vgrajeni sistemi za gorivo (ISO 10088:2013)
Ta mednarodni standard določa zahteve za zasnovo, materiale, izdelavo, vgradnjo in preskušanje sistemov za gorivo, trajno vgrajenih v motorje z notranjim izgorevanjem.
Uporablja se za vse dele trajno vgrajenih sistemov za bencinsko in dizelsko gorivo, od odprtine za dovod goriva do točke povezave z vgrajenim ali izven krmnim pogonskim ali pomožnim motorjem malih plovil z dolžino trupa do 24 m.
Zahteve za zasnovo, materiale, izdelavo in preskušanje trajno vgrajenih stacionarnih rezervoarjev za gorivo so podane v standardu ISO 21487.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2017
1DGRPHãþD
SIST EN ISO 10088:2013
Mala plovila - Trajno vgrajeni sistemi za gorivo (ISO 10088:2013)
Small craft - Permanently installed fuel systems (ISO 10088:2013)
Kleine Wasserfahrzeuge - Dauerhaft installierte Kraftstoffsysteme (ISO 10088:2013)
Petits navires - Systèmes à carburant installés à demeure (ISO 10088:2013)
Ta slovenski standard je istoveten z: EN ISO 10088:2017
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10088
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2017
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 10088:2013
English Version
Small craft - Permanently installed fuel systems (ISO
10088:2013)
Petits navires - Systèmes à carburant installés à Kleine Wasserfahrzeuge - Dauerhaft installierte
demeure (ISO 10088:2013) Kraftstoffsysteme (ISO 10088:2013)
This European Standard was approved by CEN on 9 July 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10088:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2013/53/EU . 4
European foreword
The text of ISO 10088:2013 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10088:2017.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018, and conflicting national standards
shall be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10088:2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of 10088:2013 has been approved by CEN as EN ISO 10088:2017 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2013/53/EU
This European standard has been prepared under a mandate given to CEN by the European Commission
to provide one means of conforming to Essential Requirements of the New Approach Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive and has
been implemented as a national standard in at least one member state, compliance with the normative
clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a
presumption of conformity with the relevant Essential Requirements of that Directive and associated
EFTA regulations.
Table ZA.1: Correspondence between this European Standard and Directive 2013/53/EU
Clauses/sub-clauses of this Essential Requirements Qualifying remarks/Notes
standard (ERs) of EU Directive
2013/53/EU
All Clauses Annex 1 A, Clause 5.2.1, Fuel This Standard applies to all
system -General parts of permanently
installed diesel and petrol
fuel systems as installed,
from the fuel fill opening to
the point of connection with
the propulsion or auxiliary
engine(s) on inboard- and
outboard-powered small
craft of up to 24 m hull
length.
This Standard does not
address fuel systems for
other types of diesel or petrol
burning appliances.
All Clauses Annex 1 A, Clause 5.2.2, Fuel The clauses in this standard
system –Fuel tanks address fuel lines and
ventilation of petrol tank
compartments. The design
and construction of fuel tanks
is specifically addressed by
EN ISO 21487.
4, 5 Annex 1, Clause 5.6.1 Fire The clauses in this standard
protection - General are limited to the installation
of the fuel system to
minimise the risk of fire.
4.1.7, 4.1.8, 4.2.3, 5.2.8 Annex 1 A, Clause 5.8 This standard addresses the
Discharge prevention prevention of fuel overflow
from vent openings and
blowback of fuel through fill
fittings. It does not address
accidental spillage entering
the environment.
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
INTERNATIONAL ISO
STANDARD 10088
Fourth edition
2013-08-15
Small craft — Permanently installed
fuel systems
Petits navires — Systèmes à carburant installés à demeure
Reference number
ISO 10088:2013(E)
©
ISO 2013
ISO 10088:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 10088:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 3
4.1 Materials and design . 3
4.2 Testing . 4
4.3 Installation . 4
5 Fuel pipes, hoses, connections and accessories . 4
5.1 Fuel filling lines . 4
5.2 Vent lines and components . 5
5.3 Fuel distribution, return and balancing lines . 5
5.4 Hose fittings and hose clamping . 6
5.5 Valves and fittings. 7
5.6 Fuel filters . 7
5.7 Labelling . 7
Annex A (normative) Pressure testing . 8
Bibliography . 9
ISO 10088:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 188, Small craft.
This fourth edition cancels and replaces the third edition (ISO 10088:2009), which has been technically
revised. The major changes concern 4.1.6, 4.3.2, and 5.5.4.
iv © ISO 2013 – All rights reserved
INTERNATIONAL STANDARD ISO 10088:2013(E)
Small craft — Permanently installed fuel systems
1 Scope
This International Standard specifies the requirements for the design, materials, construction, installation
and testing of permanently installed fuel systems as installed for internal combustion engines.
It applies to all parts of permanently installed diesel and petrol fuel systems as installed, from the
fuel fill opening to the point of connection with the propulsion or auxiliary engine(s) on inboard- and
outboard-powered small craft of up to 24 m hul
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.