EN ISO 13000-1:2005

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)

ISO 13000-1:2005 specifies the requirements for processed unfilled polytetrafluoroethylene (PTFE) products which may occur in several forms. The PTFE used to make the semi-finished product is described in ISO 12086-1 and, as provided in ISO 12086-1, may contain up to 1 % of a comonomer. The PTFE used to make the semi-finished product may be virgin, reprocessed or recycled resin. The addition of up to 1,5 % by mass of pigment or colorant is permitted. This part of ISO 13000 allows for four grades based on tensile strength and elongation at break. The semi-finished products can be as-processed (type P) or dimensionally stabilized (type S) and may also have specified electrical properties or other properties when they are required for an application.

Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil 1: Anforderungen und Bezeichnung (ISO 13000-1:2005)

Dieser Teil von ISO 13000 legt Anforderungen für verarbeitete, ungefüllte Polytetrafluorethylen (PTFE)-Produkte, die in verschiedenen Formen vorliegen können, fest. Das zur Herstellung von PTFE-Halbzeug verwendete PTFE wird in ISO 12086 1 beschrieben und darf nach ISO 12086-1 Angaben bis zu 1 % eines Comonomer enthalten. Bei dem zur Herstellung von Halbzeug verwendeten PTFE kann es sich um virginales oder wiederverarbeitetes Harz handeln. Der Zusatz von Pigmenten oder Farbstoffen ist bis zu einem Massenanteil von 1,5 % zulässig. Hinsichtlich der Zugfestigkeit und Bruchdehnung sind in diesem Teil von ISO 13000 vier verschiedene Klassen vorgesehen. Das Halbzeug kann ohne Nachbehandlung (Typ P) oder dimensionsstabilisiert sein (Typ S) und kann festgelegte elektrische Eigenschaften oder andere Merkmale aufweisen, sofern sie für eine bestimmte Anwendung vorgeschrieben sind.
ANMERKUNG   Zur Information wird in Anhang A auf andere Spezifikationsnormen für Halbzeuge aus Polytetrafluorethylen verwiesen.

Plastiques - Semi-produits en polytétrafluoroéthylène (PTFE) - Partie 1: Spécifications et désignation (ISO 13000-1:2005)

L'ISO 13000-1:2005 spécifie les exigences relatives aux produits en polytétrafluoroéthylène (PTFE) mis en oeuvre et non chargés qui peuvent se présenter sous diverses formes. Le PTFE utilisé pour fabriquer le semi-produit est décrit dans l'ISO 12086-1 et, comme cela est indiqué dans l'ISO 12086-1 peut contenir jusqu'à 1 % d'un quelconque comonomère. Le PTFE utilisé pour fabriquer le semi-produit peut être une résine vierge, régénérée ou recyclée. Il est permis d'ajouter jusqu'à 1,5 % en masse de pigment ou colorant. L'ISO 13000-1 admet l'emploi de quatre qualités basées sur la résistance à la traction et l'allongement à la rupture. Les semi-produits peuvent être bruts de mise en oeuvre (type P) ou dimensionnellement stabilisés (type S) et ils peuvent être caractérisés par certaines propriétés électriques ou autres, lorsqu'elles sont requises pour une application donnée.

Polimerni materiali – Polizdelki iz politetrafluoroetilena (PTFE) – 1. del: Zahteve in označevanje(ISO/DIS 13000-1:2004)

General Information

• Status: Withdrawn
• Publication Date: 14-Nov-2005
• Withdrawal Date: 31-Aug-2021
• ICS: 83.140.01 - Rubber and plastics products in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 11 - Fluoroplastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 01-Sep-2021
• Ref Project: SIST EN ISO 13000-1:2006 - Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)

Relations

• Replaces: EN ISO 13000-1:1997 - Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:1997)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 13000-1:2021 - Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2021)
• Effective Date: 15-Jan-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13000-1:2006
01-april-2006
1DGRPHãþD
SIST EN ISO 13000-1:1999
3ROLPHUQLPDWHULDOL±3ROL]GHONLL]SROLWHWUDIOXRURHWLOHQD37)(±GHO=DKWHYHLQ
R]QDþHYDQMH,62',6
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements
and designation (ISO 13000-1:2005)
Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil 1: Anforderungen und
Bezeichnung (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylene (PTFE) - Partie 1: Spécifications et
désignation (ISO 13000-1:2005)
Ta slovenski standard je istoveten z: EN ISO 13000-1:2005
ICS:
83.140.01 Izdelki iz gume in polimernih Rubber and plastics products
materialov na splošno in general
SIST EN ISO 13000-1:2006 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13000-1:2006

---------------------- Page: 2 ----------------------

SIST EN ISO 13000-1:2006
EUROPEAN STANDARD
EN ISO 13000-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 83.140.01 Supersedes EN ISO 13000-1:1997
English Version
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products
- Part 1: Requirements and designation (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylène Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil
(PTFE) - Partie 1: Spécifications et désignation (ISO 1: Anforderungen und Bezeichnung (ISO 13000-1:2005)
13000-1:2005)
This European Standard was approved by CEN on 4 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13000-1:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13000-1:2006

EN ISO 13000-1:2005 (E)





Foreword


This document (EN ISO 13000-1:2005) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.

This document supersedes EN ISO 13000-1:1997.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 13000-1:2005 has been approved by CEN as EN ISO 13000-1:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 13000-1:2006

INTERNATIONAL ISO
STANDARD 13000-1
Second edition
2005-11-15

Plastics — Polytetrafluoroethylene
(PTFE) semi-finished products —
Part 1:
Requirements and designation
Plastiques — Semi-produits en polytétrafluoroéthylène (PTFE) —
Partie 1: Spécifications et désignation




Reference number
ISO 13000-1:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringi
...