iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14710-2:2005

(Main)

Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements

Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements

The document specifies the requirements for testing fire fighting centrifugal pumps without priming devices up to a delivery rate of 6000 l/min as specified in EN XXXX.

Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung - Teil 2: Feststellung der Übereinstimmung mit den allgemeinen Anforderungen und den Sicherheitsanforderungen

Dieses Dokument gilt für die Feststellung der Übereinstimmung mit den allgemeinen Anforderungen und den
Sicherheitsanforderungen von Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung entsprechend den
Festlegungen in EN 14710-1.
ANMERKUNG Die Prüfungen können auch an Pumpen mit Nennförderströmen über 6 000 l/min durchgeführt werden.
Dieses Dokument gilt nicht für Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung, die hergestellt wurden,
bevor CEN diese Norm veröffentlichte.

Pompes à usage incendie - Pompes centrifuges à usage incendie sans dispositif d'amorçage - Partie 2 : Vérification des prescriptions générales et de sécurité

Le présent document traite de la vérification des prescriptions générales et de sécurité des pompes
centrifuges à usage incendie sans dispositif d�amorçage, telles que définies dans l�EN 14710-1.
NOTE Les essais peuvent aussi s'appliquer aux pompes ayant un débit de refoulement nominal supérieur à
6 000 l/min.
Le présent document ne s�applique pas aux pompes centrifuges à usage incendie sans dispositif d�amorçage
qui ont été fabriquées avant la date de publication par le CEN du présent document.

Gasilske črpalke - Gasilske centrifugalne črpalke brez sesalne naprave - 2. del: Preverjanje splošnih in varnostnih zahtev

General Information

Status
Withdrawn
Publication Date
08-Feb-2005
Withdrawal Date
08-Apr-2008
ICS
13.220.10 - Fire-fighting
Technical Committee
CEN/TC 192 - Fire service equipment
Drafting Committee
CEN/TC 192/WG 2 - Firefighting pumps
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
09-Apr-2008
Completion Date
09-Apr-2008
Directive
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
Ref Project
SIST EN 14710-2:2005 - Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements

Relations

Merged Into
EN 14710-2:2005+A1:2008 - Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements
Effective Date
19-Jan-2023
Merged Into
EN 14710-2:2005+A2:2008 - Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements
Effective Date
22-Dec-2008

Buy Standard

EN 14710-2:2005EN 14710-2:2005
PreviousNext
Standard
EN 14710-2:2005
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14710-2:2005
01-april-2005
*DVLOVNHþUSDONH*DVLOVNHFHQWULIXJDOQHþUSDONHEUH]VHVDOQHQDSUDYHGHO
3UHYHUMDQMHVSORãQLKLQYDUQRVWQLK]DKWHY
Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification
of general and safety requirements
Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne Entlüftungseinrichtung - Teil 2:
Feststellung der Übereinstimmung mit den allgemeinen Anforderungen und den
Sicherheitsanforderungen
Pompes a usage incendie - Pompes centrifuges a usage incendie sans dispositif
d'amorçage - Partie 2 : Vérification des prescriptions générales et de sécurité
Ta slovenski standard je istoveten z: EN 14710-2:2005
ICS:
13.220.10 Gašenje požara Fire-fighting
SIST EN 14710-2:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14710-2:2005

---------------------- Page: 2 ----------------------

SIST EN 14710-2:2005
EUROPEAN STANDARD
EN 14710-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS 13.220.10
English version
Fire-fighting pumps - Fire-fighting centrifugal pumps without
primer - Part 2: Verification of general and safety requirements
Pompes à usage incendie - Pompes centrifuges à usage Feuerlöschpumpen - Feuerlöschkreiselpumpen ohne
incendie sans dispositif d'amorçage - Partie 2 : Vérification Entlüftungseinrichtung - Teil 2: Feststellung der
des prescriptions générales et de sécurité Übereinstimmung mit den allgemeinen Anforderungen und
den Sicherheitsanforderungen
This European Standard was approved by CEN on 17 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14710-2:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14710-2:2005
EN 14710-2:2005 (E)
Contents
Page
Foreword .4
0 Introduction.5
1 Scope.6
2 Normative references.6
3 Terms and definitions .6
4 Verification, Principles.6
5 Verification of the safety requirements and/or protective measures .9
6 Verification of the general and performance requirements.12
7 Test report.15
Annex A (normative) Mounting positions for tests at inlet height.16
Annex B (normative)  Pressure measurements .18
Annex C (normative)  Measurements of delivery rates .19
Annex D (normative)  Performance test.20
Annex E (normative)  Endurance test .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 14557:2021(Main)
Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies (ISO 14557:2021)
SIST EN ISO 14557:2021

This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge.
NOTE       All pressures are expressed in megapascals and in bar (1 MPa = 10 bar).
Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8).
Type A (rubber) hoses are intended for use at a minimum temperature of −20 °C and Type B (thermoplastics) hoses are intended for use at a minimum temperature of −10 °C.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17407:2020(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Collecting heads and dividing breechings PN 16
SIST EN 17407:2020

1.1   This document defines requirements and tests which apply to:
-   collecting heads with a nominal pressure of 16 bar (1,6 MPa) PN 16 which are used by fire and rescue services to combine two or more inlets into one or more outlets;
-   dividing breechings with a nominal pressure of 16 bar (1,6 MPa) PN 16 which are used by fire and rescue services to divide one or more inlets into two or more outlets.
NOTE 1   In this document "ColDiv" is used to refer both to collecting heads and dividing breechings.
NOTE 2   In this document, drawings of collecting heads and dividing breechings are shown inlets downwards and outlet upwards.
1.2   This document is not applicable to collecting heads or dividing breechings which have been manufactured before its date of publication as European standard.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15182-2:2019(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 2: Combination branchpipes PN 16
SIST EN 15182-2:2019

In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held combination branchpipes (nozzles), with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
- safety requirements;
- performance requirements;
- test methods.
This document applies to branchpipes as defined in Annex A of EN 15182-1:2019.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15182-1:2019(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 1: Common requirements
SIST EN 15182-1:2019

This document applies to hand-held branchpipes. It deals with:
- safety requirements;
- performance requirements;
- test methods;
- classification and designation;
- instructions for use and maintenance;
- marking.
It is advised to read this document in conjunction with parts 2, 3 or 4.
This document does not apply to branchpipes covered by EN 671 series, foam branchpipes covered by EN 16712-3, powder branchpipes, or branchpipes with a maximum working pressure above 40 bar.
NOTE 1   The Working Group has thoroughly addressed and discussed the issue of electrical safety in relation to using water branchpipes. However, an electrical test is not incorporated into this document as international experience, as well as research (NFPA handbook, French research, etc) have shown that any "artificial" or "laboratory style" testing will not take into account poor visibility and other conditions present on any fire ground, nor the problem of estimating distances under these conditions. When fighting fires in or near electrical installations, the power is cut off as soon as possible (see the operating instructions, 8.1). Also, it is best practice to maintain a maximum possible safety distance (at least 1 m up to 1 000 V) and to use a spray jet with a minimum spray angle of 30 °.
NOTE 2   It is essential to take into account reaction forces before choosing and operating branchpipes.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15182-4:2019(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 4: High pressure branchpipes PN 40
SIST EN 15182-4:2019

In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held high pressure branchpipes (nozzles) with a nominal pressure of 40 bar (4,0 MPa) PN 40, with a maximum flow rate up to 250 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
- safety requirements;
-  performance requirements;
- test methods.
This document applies to branchpipes as defined in Annex A of EN 15182-1:2019.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15182-3:2019(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
SIST EN 15182-3:2019

In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held branchpipes with smooth bore jet and/or one fixed spray jet angle branchpipes with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
- safety requirements;
- performance requirements;
- test methods.
This document applies to branchpipes as defined in Annex A of EN 15182-1:2019.
WARNING 1 — These branchpipes offer no or inadequate protection for firefighters when the spray angle is less than 30 ° and therefore, are not be used in high risk firefighting situations such as internal attack.
WARNING 2 — These branchpipes should not be used when fighting fires in or near electrical installations when the spray angle is less than 30° without written authorization from the manufacturer in the manual. This authorization from the manufacturer includes safety distances.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16712-4:2018(Main)
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Portable foam equipment - Part 4: High expansion foam generators PN16
SIST EN 16712-4:2018

1.1   This document applies to high expansion foam generators, having an expansion ratio greater than 200:1, whose only source of external power is the pressure and/or flow of the water supply to the device. This is used by fire and rescue services and contains their specification and test procedures.
NOTE   In this document, the term"foam generator" also refers to "high expansion foam generator".
1.2   This document deals with all significant hazards, hazardous situations or hazardous events, with the exception of noise, relevant to high expansion foam generator, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
1.3   This document does not cover misting applications.
1.4   This document is not applicable to high expansion foam generators which have been manufactured before its date of publication as EN.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13204:2016(Main)
Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements
SIST EN 13204:2016

This European Standard specifies safety and performance requirements for double acting hydraulic rescue tools manufactured after the date of publication.
It is applicable to double acting hydraulic rescue tool systems which are intended for use by the firefighting and rescue services, principally for cutting through, spreading or pushing apart the structural parts of road vehicles, ships, trains, aircraft and building structures involved in accidents. They consist of a separate power pack, the tool[s] and the necessary interconnections and intended accessories, as defined in Clause 3 – Terms and definitions.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to the machinery, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
NOTE 1   The aim is to assist while extracting the casualties or to create a working space for paramedical services taking the local conditions into account.
It is not applicable to additional requirements for:
a)   operation in severe conditions (e.g. extreme environmental conditions such as: temperatures outside the range –20 °C up to +55 °C, corrosive environment, tropical environment, contaminating environments, strong magnetic fields, potentially explosive atmospheres);
b)   the risk directly arising from the means provided for the portability, transportability and mobility of double-acting hydraulic rescue tools during periods of their operation.
NOTE 2   For the EU/EEA other Directives can be applicable to the equipment in the scope, for example the Electro Magnetic Compatibility Directive.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16712-2:2015(Main)
Portable equipment for projecting extinguishing agents supplied by fire fighting pumps - Portable foam equipment - Part 2: Pick-up tubes
SIST EN 16712-2:2015

1.1   This European Standard specifies performance requirements and test methods for pick-up tubes.
This European Standard applies to pick-up tubes from DN 20 to DN 50 which are used for the suction of foam concentrate or additives and defines their requirements and test procedures.
Pick-up tubes are especially used with inductors in accordance with prEN 16712-1.
NOTE   Pick-up tubes can also be used for the suction of other substances (e.g. absorbents).
1.2   This European Standard is not applicable to pick-up tubes which have been manufactured before its date of publication as European Standard.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16712-3:2015(Main)
Portable equipment for projecting extinguishing agents supplied by fire fighting pumps - Portable foam equipment - Part 3: Low and medium expansion hand-held foam branchpipes PN 16

1.1   This European Standard applies to handheld foam branchpipes, and self-inducting foam branchpipes, for low and medium expansion foam used by fire and rescue services and defines their specification and test procedures.
NOTE   In this European Standard, the term "branchpipe" also refers to "hand-held foam branchpipes".
1.2   This European Standard is not applicable to hand-held foam branchpipes which have been manufactured before its date of publication as European Standard.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day