EN ISO 293:2005

Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004)

ISO 293:2004 specifies the general principles and the procedures to be followed with thermoplastics in the preparation of compression-moulded test specimens, and sheets from which test specimens may be machined or stamped.

Kunststoffe - Formgepresste Probekörper aus Thermoplasten (ISO 293:2004)

Diese Internationale Norm legt die allgemeinen Prinzipien und Verfahren fest, die für Thermoplaste bei der Herstellung von formgepressten Probekörpern und Platten zu befolgen sind, aus denen durch maschinelles Bearbeiten oder Stanzen Probekörper hergestellt werden können.
Um einen vergleichbaren Zustand bei den Formpressteilen zu erzielen, sind die Hauptschritte des Verfahrens, einschließlich vier unterschiedlicher Abkühlverfahren, genormt. Die erforderliche Presstemperatur und die Abkühlverfahren sind für jedes Material so, wie es in der entsprechenden Internationalen Norm für das Material festgelegt ist oder zwischen den beteiligten Partnern vereinbart wurde.
Das Verfahren wird nicht für verstärkte thermoplastische Kunststoffe empfohlen

Plastiques - Moulage par compression des éprouvettes en matières thermoplastiques (ISO 293:2004)

L'ISO 293:2004 spécifie les principes généraux et les modes opératoires à suivre, dans le cas de matières thermoplastiques, pour la préparation d'éprouvettes moulées par compression et de plaques nécessaires pour l'usinage ou la découpe d'éprouvettes.

Polimerni materiali - Preskušanci plastomerov, oblikovani s stiskanjem (ISO 293:2004)

General Information

• Status: Withdrawn
• Publication Date: 26-Jul-2005
• Withdrawal Date: 07-Mar-2023
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Ref Project: SIST EN ISO 293:2005 - Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004)

Relations

• Replaces: EN ISO 293:2003 - Plastics - Compression moulding test specimens of thermoplastic materials (ISO 293:1986)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 293:2023 - Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2023)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 293:2005
01-oktober-2005
1DGRPHãþD
SIST EN ISO 293:2003
Polimerni materiali - Preskušanci plastomerov, oblikovani s stiskanjem (ISO
293:2004)
Plastics - Compression moulding of test specimens of thermoplastic materials (ISO
293:2004)
Kunststoffe - Formgepresste Probekörper aus Thermoplasten (ISO 293:2004)
Plastiques - Moulage par compression des éprouvettes en matieres thermoplastiques
(ISO 293:2004)
Ta slovenski standard je istoveten z: EN ISO 293:2005
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 293:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 293
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS 83.080.20 Supersedes EN ISO 293:2003
English Version
Plastics - Compression moulding of test specimens of
thermoplastic materials (ISO 293:2004)
Plastiques - Moulage par compression des éprouvettes en Kunststoffe - Formgepresste Probekörper aus
matières thermoplastiques (ISO 293:2004) Thermoplasten (ISO 293:2004)
This European Standard was approved by CEN on 7 July 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 293:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 293:2005 (E)






Foreword



The text of ISO 293:2004 has been prepared by Technical Committee ISO/TC 61 "Plastics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO
293:2005 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by
IBN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2006, and conflicting national
standards shall be withdrawn at the latest by January 2006.

This document supersedes EN ISO 293:2003.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 293:2004 has been approved by CEN as EN ISO 293:2005 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 293
Third edition
2004-05-01
Plastics — Compression moulding of test
specimens of thermoplastic materials
Plastiques — Moulage par compression des éprouvettes en matières
thermoplastiques

Reference number
ISO 293:2004(E)
©
ISO 2004

---------------------- Page: 4 ----------------------

ISO 293:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the
...