EN 60684-3-283:2011
(Main)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
IEC 60684-3-283:2010 gives the requirements for two types of heat-shrinkable, polyolefin sleeving for bus-bar insulation, with a nominal shrink ratio of 2,5:1. This sleeving has been found suitable up to temperatures of 100 °C. - Type A: Medium wall Internal diameter up to 170,0 mm typically - Type B: Thick wall Internal diameter up to 165,0 mm typically.
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283: Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barre omnibus
La CEI 60684-3-283:2010 donne les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, pour isolation des barres omnibus de rapport de rétreint nominal 2,5:1. Ces gaines se sont révélées être adaptées à des températures jusqu'à 100 °C. - Type A: Paroi moyenne Diamètre intérieur type jusqu'à 170,0 mm - Type B: Paroi épaisse Diamètre intérieur type jusqu'à 165,0 mm.
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - List 283: Toplotno skrčljive poliolefinske cevi za izolacijo zbiralk (IEC 60684-3-283:2010)
Ta del IEC 60684 podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi za izolacijo zbiralk, ki imajo nazivno razmerje krčenja do 2,5 : 1. Za te cevi je ugotovljeno, da so primerne za uporabo pri temperaturah do 100 °C.
- Tip A: Srednje debela stena. Notranji premer običajno do 170,0 mm.
- Tip B: Debela stena. Notranji premer običajno do 165,0 mm.
Te cevi se običajno dobavljajo v barvah, rdeči ali rjavi. Ker te vrste cevi zajemajo precej velik razpon velikosti in debelin stene, preglednici A.1 in A.2 podajata navodilo o razponu razpoložljivih velikosti. Dejanska velikost in debelina stene morata biti dogovorjeni med uporabnikom in dobaviteljem in sta odvisni od električne moči nameščenih cevi, ki so na voljo, in zahtev uporabnika. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri taki uporabi, ne le na podlagi same specifikacije.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283: Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen (IEC 60684-3-283:2010)Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barre omnibus (CEI 60684-3-283:2010)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation (IEC 60684-3-283:2010)29.035.20PDWHULDOLPlastics and rubber insulating materialsICS:Ta slovenski standard je istoveten z:EN 60684-3-283:2011SIST EN 60684-3-283:2011en01-marec-2011SIST EN 60684-3-283:2011SLOVENSKI
STANDARD
SIST EN 60684-3-283:2011
EUROPEAN STANDARD EN 60684-3-283 NORME EUROPÉENNE
EUROPÄISCHE NORM January 2011
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-283:2011 E
ICS 29.035.20
English version
Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation (IEC 60684-3-283:2010)
Gaines isolantes souples -
Partie 3: Spécifications pour types particuliers de gaines -
Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barre omnibus (CEI 60684-3-283:2010)
Isolierschläuche -
Teil 3: Anforderungen für einzelne Schlauchtypen -
Blatt 283: Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen (IEC 60684-3-283:2010)
This European Standard was approved by CENELEC on 2011-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 60684-3-283:2011
EN 60684-3-283:2011 - 2 - Foreword The text of document 15/597/FDIS, future edition 1 of IEC 60684-3-283, prepared by IEC TC 15, Solid electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-283 on 2011-01-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2011-10-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2014-01-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 60684-3-283:2010 was approved by CENELEC as a European Standard without any modification. __________ SIST EN 60684-3-283:2011
- 3 - EN 60684-3-283:2011 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60296 2003 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear EN 60296 + corr. September 2004 2004
IEC 60684-1 2003 Flexible insulating sleeving -
Part 1: Definitions and general requirements EN 60684-1 2003
IEC 60684-2
+ A1 + A2 1997 2003 2005 Flexible insulating sleeving -
Part 2: Methods of test EN 60684-2 + A1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.