EN 60317-0-4:2016

Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire

IEC 60317-0-4:2015 specifies general requirements of glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. This third edition cancels and replaces the second edition published in 1997, Amendment 1:1999 and Amendment 2:2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of dimensional requirements for grade 1 enamelled wire in Table 4; - addition of dielectric breakdown requirements for grade 1 enamelled wire in Table 7. Keywords: insulated wires used for windings, copper wire

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-4: Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert und umhüllt mit Glasgewebe, imprägniert mit Harz oder Lack

Spécifications pour types particuliers de fils de bobinage - Partie 0-4: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre imprégnées de vernis ou de résine

L'IEC 60317-0-4:2015 spécifie les exigences générales relatives au fil de section rectangulaire en cuivre nu ou émaillé guipé de fibres de verre imprégnées de vernis ou de résine. La plage des dimensions nominales des conducteurs est donnée dans la feuille particulière concernée. Cette troisième édition annule et remplace la deuxième édition parue en 1997, l'Amendement 1:1999 et l'Amendement 2:2005. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - ajout d'exigences relatives aux dimensions pour le fil émaillé de grade 1 dans le Tableau 4; - ajout d'exigences relatives au claquage pour le fil émaillé de grade 1 dans le Tableau 7. Mots clés: fils isolés utilisés pour les enroulements, fil de cuivre

Specifikacije za posebne vrste navijalnih žic - 0-4. del: Splošne zahteve - Bakrena žica s pravokotnim prerezom, gola ali emajlirana, ovita z optičnimi vlakni in impregnirana s smolo ali lakom

Ta del standarda IEC 60317 določa splošne zahteve za bakreno žico s pravokotnim prerezom, golo ali emajlirano, ovito z optičnimi vlakni in impregnirano s smolo ali lakom. Obseg nazivnih mer kondenzatorja je podan v ustrezni razpredelnici.

General Information

• Status: Withdrawn
• Publication Date: 21-Jan-2016
• Withdrawal Date: 26-Nov-2018
• ICS: 29.060.10 - Wires
• Technical Committee: CLC/TC 55 - Winding wires
• Drafting Committee: IEC/TC 55 - IEC_TC_55
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 01-Jun-2023
• Completion Date: 01-Jun-2023
• Ref Project: SIST EN 60317-0-4:2016 - Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire

Relations

• Replaces: EN 60317-0-4:1998/A1:2000 - Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
• Effective Date: 07-Jun-2022
• Replaces: EN 60317-0-4:1998/A2:2005 - Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
• Effective Date: 26-Jan-2016
• Replaces: EN 60317-0-4:1998 - Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
• Effective Date: 26-Jan-2016
• Replaced By: EN IEC 60317-0-4:2020 - Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
• Effective Date: 30-Jun-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2016
1DGRPHãþD
SIST EN 60317-0-4:2001
SIST EN 60317-0-4:2001/A1:2001
SIST EN 60317-0-4:2001/A2:2006
6SHFLILNDFLMH]DSRVHEQHYUVWHQDYLMDOQLKåLFGHO6SORãQH]DKWHYH%DNUHQD
åLFDVSUDYRNRWQLPSUHUH]RPJRODDOLHPDMOLUDQDRYLWD]RSWLþQLPLYODNQLLQ
LPSUHJQLUDQDVVPRORDOLODNRP
Specifications for particular types of winding wires - Part 0-4: General requirements -
Glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper
wire
Ta slovenski standard je istoveten z: EN 60317-0-4:2016
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60317-0-4

NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2016
ICS 29.060.10 Supersedes EN 60317-0-4:1998
English Version
Specifications for particular types of winding wires - Part 0-4:
General requirements - Glass-fibre wound, resin or varnish
impregnated, bare or enamelled rectangular copper wire
(IEC 60317-0-4:2015)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-4: Exigences générales - Fil de section Wickeldrähten - Teil 0-4: Allgemeine Anforderungen -
rectangulaire en cuivre nu ou émaillé, guipé de fibres de Flachdrähte aus Kupfer, blank oder lackisoliert und umhüllt
verre imprégnées de vernis ou de résine mit Glasgewebe, imprägniert mit Harz oder Lack
(IEC 60317-0-4:2015) (IEC 60317-0-4:2015)
This European Standard was approved by CENELEC on 2015-11-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-0-4:2016 E
European foreword
The text of document 55/1550/FDIS, future edition 3 of IEC 60317-0-4, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2016-08-27
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-11-27
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60317-0-4:1998.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-4:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 NOTE Harmonized in EN 60264 series.
IEC 60317 NOTE Harmonized in EN 60317 series.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60851 series Winding wires - Test methods EN 60851 series

IEC 60317-0-4 ®
Edition 3.0 2015-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-4: General requirements – Glass-fibre wound, resin or varnish

impregnated, bare or enamelled rectangular copper wire

Spécifications pour types particuliers de fils de bobinage –

Partie 0-4: Exigences générales – Fil de section rectangulaire en cuivre nu ou

émaillé, guipé de fibres de verre imprégnées de vernis ou de résine

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-2975-0

– 2 – IEC 60317-0-4:2015 © IEC 2015
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and general notes on tests and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 8
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor dimensions . 9
4.2 Tolerance on conductor dimensions . 11
4.3 Rounding of corners . 11
4.4 Increase in dimensions due to the insulation . 11
4.5 Overall dimensions . 13
4.5.1 Nominal overall dimensions . 13
4.5.2 Minimum overall dimensions . 13
4.5.3 Maximum overall dimensions . 13
5 Electrical resistance . 13
6 Elongation . 13
7 Springiness . 13
8 Flexibility and adherence . 14
8.1 Mandrel winding test . 14
8.2 Adherence test . 14
8.2.1 Glass-fibre covered bare wires . 14
8.2.2 Glass-fibre covered enamelled wires . 14
9 Heat shock . 14
10 Cut-through . 14
11 Resistance to abrasion . 14
12 Resistance to solvents . 14
13 Breakdown voltage . 14
14 Continuity of insulation . 15
15 Temperature index . 15
16 Resistance to refrigerants . 15
17 Solderability . 15
18 Heat or solvent bonding . 15
19 Dielectric dissipation factor . 15
20 Resistance to transformer oil . 15
21 Loss of mass . 15
23 Pin hole test . 16
30 Packaging . 16

IEC 60317-0-4:2015 © IEC 2015 – 3 –
Annex A (informative) Nominal cross-sectional areas for preferred and intermediate
sizes . 17
Bibliography . 24

Table 1 – Nominal cross-sectional areas of preferred sizes . 10
Table 2 – Conductor tolerances . 11
Table 3 – Corner radii . 11
Table 4 – Increase in dimensions . 12
Table 5 – Elongation . 13
Table 6 – Mandrel winding . 14
Table 7 – Breakdown voltage . 15
Table A.1 – Nominal cross-sectional areas (1 of 7) . 17

– 4 – IEC 60317-0-4:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-4: General requirements –
Glass-fibre wound, resin or varnish impregnated,
bare or enamelled rectangular copper wire

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardiza
...