EN IEC 60317-0-6:2020
(Main)Specifications for particular types of winding wires - Part 0-6: General requirements - Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire
Specifications for particular types of winding wires - Part 0-6: General requirements - Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire
IEC 60317-0-6:2020 is available as IEC 60317-0-6:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60317-0-6:2020 specifies the general requirements of glass-fibre wound resin or varnish impregnated, bare or enamelled, round copper winding wires. The range of nominal conductor diameters is given in the relevant specification sheet. This second edition cancels and replaces the first edition published in 2001 and Amendment 1:2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - revision to 3.3, Appearance; - revision to Table 1, maximum overall diameter of grade 1 wire over single-glass fibre covering for nominal conductor diameters 1,600 mm - 5,000 mm; - revision to Table 2, maximum overall diameter of grade 1 wire over double-glass fibre covering for nominal conductor diameters 1,600 mm - 5,000 mm; clarification in Table 3 measurement of elongation as “minimum elongation %”.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-6: Allgemeine Anforderungen - Runddrähte aus Kupfer, blank oder lackisoliert, mit Glas-Fasergewebe umsponnen und mit Harz oder Lack imprägniert
Spécifications pour types particuliers de fils de bobinage - Partie 0-6: Exigences générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre imprégnées de résine ou de vernis
IEC 60317-0-6:2020 est disponible sous forme de IEC 60317-0-6:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 60317-0-6:2020 spécifie les exigences générales relatives aux fils de bobinage de section circulaire en cuivre, nus ou émaillés, guipés de fibres de verre imprégnées de résine ou de vernis. La gamme des diamètres nominaux des conducteurs est donnée dans la feuille de spécification applicable. Cette deuxième édition annule et remplace la première édition parue en 2001 et l'Amendement 1:2006. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - révision du 3.3, Aspect; - révision du Tableau 1, diamètre extérieur maximal de fil de grade 1 sur une enveloppe de fibres de verre simple couche pour les diamètres nominaux des conducteurs 1,600 mm - 5,000 mm; - révision du Tableau 2, diamètre extérieur maximal de fil de grade 1 sur une enveloppe de fibres de verre double couche pour les diamètres nominaux des conducteurs 1,600 mm - 5,000 mm; - clarification dans le Tableau 3 concernant le mesurage de l’allongement pour bien établir qu’il s’agit de “l’allongement minimal en %”.
Specifikacije za posebne vrste navijalnih žic - 0-6. del: Splošne zahteve - Z optičnimi vlakni ovita, gola ali emajlirana, impregnirana s smolo ali lakom okrogla bakrena žica (IEC 60317-0-6:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2020
Nadomešča:
SIST EN 60317-0-6:2002
SIST EN 60317-0-6:2002/A1:2007
Specifikacije za posebne vrste navijalnih žic - 0-6. del: Splošne zahteve - Z
optičnimi vlakni ovita, gola ali emajlirana, impregnirana s smolo ali lakom okrogla
bakrena žica (IEC 60317-0-6:2020)
Specifications for particular types of winding wires - Part 0-6: General requirements -
Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire
(IEC 60317-0-6:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 0-6:
Allgemeine Anforderungen – Runddrähte aus Kupfer, blank oder lackisoliert, mit
Glasgewebe umsponnen und mit Harz oder Lack imprägniert (IEC 60317-0-6:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 0-6: Prescriptions
générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre
imprégnées de résine ou de vernis (IEC 60317-0-6:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-0-6:2020
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60317-0-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 29.060.10 Supersedes EN 60317-0-6:2001 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 0-6:
General requirements - Glass-fibre wound resin or varnish
impregnated, bare or enamelled round copper wire
(IEC 60317-0-6:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-6: Exigences générales - Fil de section circulaire Wickeldrähten - Teil 0-6: Allgemeine Anforderungen -
en cuivre nu ou émaillé, guipé de fibres de verre Runddrähte aus Kupfer, blank oder lackisoliert, mit
imprégnées de résine ou de vernis Glasgewebe umsponnen und mit Harz oder Lack
(IEC 60317-0-6:2020) imprägniert
(IEC 60317-0-6:2020)
This European Standard was approved by CENELEC on 2020-07-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-0-6:2020 E
European foreword
The text of document 55/1851/FDIS, future edition 2 of IEC 60317-0-6, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-14
document have to be withdrawn
This document supersedes EN 60317-0-6:2001 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-6:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60317-0-1 NOTE Harmonized as EN 60317-0-1
IEC 60317-48 NOTE Harmonized as EN 60317-48
IEC 60317-49 NOTE Harmonized as EN 60317-49
IEC 60317-50 NOTE Harmonized as EN 60317-50
IEC 60851-6 NOTE Harmonized as EN 60851-6
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60851 series Methods of test for winding wires EN 60851 series
IEC 60851-5 2008 Winding wires - Test methods - Part 5: EN 60851-5 2008
Electrical properties
+ A1 2011 + A1 2011
+ A2 2019 + A2 2019
ISO 3 - Preferred numbers - Series of preferred - -
numbers
IEC 60317-0-6 ®
Edition 2.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 0-6: General requirements – Glass-fibre wound resin or varnish
impregnated, bare or enamelled round copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-6: Exigences générales – Fil de section circulaire en cuivre nu
ou émaillé, guipé de fibres de verre imprégnées de résine ou de vernis
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-8427-8
– 2 – IEC 60317-0-6:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor diameter . 9
4.2 Out of roundness of the conductor . 11
4.3 Minimum increase in diameter due to the covering . 11
4.4 Maximum overall diameter . 11
5 Electrical resistance . 12
6 Elongation . 12
7 Springiness . 12
7.1 Nominal conductor diameters up to and including 1,600 mm . 12
7.2 Nominal conductor diameters over 1,600 mm . 12
8 Flexibility and adherence . 12
9 Heat shock . 12
10 Cut-through . 12
11 Resistance to abrasion . 12
12 Resistance to solvents . 13
13 Breakdown voltage . 13
13.1 Glass-fibre covered bare round copper wires . 13
13.2 Glass-fibre covered enamelled round copper wires . 13
14 Continuity of insulation . 13
15 Temperature index . 13
16 Resistance to refrigerants . 14
17 Solderability . 14
18 Heat or solvent bonding . 14
19 Dielectric dissipation factor . 14
20 Resistance to hydrolysis and to transformer oil . 14
21 Loss of mass . 14
23 Pin hole test . 14
30 Packaging . 14
Annex A (informative) Diameters for intermediate nominal conductor diameters (R40) . 15
Annex B (informative) Resistance . 17
Bibliography . 18
IEC 60317-0-6:2020 © IEC 2020 – 3 –
Table 1 – Diameters for single glass-fibre covered grade 1 or grade 2 enamelled round
wires . 10
Table 2 – Diameters for double glass-fibre covered, bare, grade 1 or grade 2
enamelled round wires . 10
Table 3 – Elongation . 12
Table 4 – Breakdown voltage for glass-fibre covered bare round copper wires . 13
Table 5 – Breakdown voltage of glass fibre-covered enamelled round copper wires . 13
Table A.1 – Diameters for single glass-fibre covered grade 1 or grade 2 enamelled
round wires (R40) . 15
Table A.2 – Diameters for double glass-fibre covered, bare, grade 1 or grade 2
enamelled round wires (R40) . 16
Table B.1 – Electrical resistances . 17
– 4 – IEC 60317-0-6:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 0-6: General requirements –
Glass-fibre wound resin or varnish impregnated,
bare or enamelled round copper wire
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.