Semiconductor devices - Mechanical and climatic test methods - Part 15: Resistance to soldering temperature for through-hole mounted devices

IEC 60749-15:2010 describes a test used to determine whether encapsulated solid state devices used for through-hole mounting can withstand the effects of the temperature to which they are subjected during soldering of their leads by using wave soldering or a soldering iron. This second edition cancels and replaces the first edition published in 2003 and constitutes a technical revision. The significant changes with respect from the previous edition include: - editorial change in the scope; - addition of lead-free solder chemical composition specification.

Halbleiterbauelemente - Mechanische und klimatische Prüfverfahren - Teil 15: Beständigkeit gegen Löttemperatur bei Bauelementen zur Durchsteckmontage

Dispositifs à semiconducteurs - Méthodes d’essai mécaniques et climatiques - Partie 15: Résistance à la température de soudage pour dispositifs par trous traversants

La CEI 60749-15:2010 décrit un essai utilisé pour déterminer si les dispositifs à solide encapsulés utilisés pour le montage par trous traversants peuvent résister aux effets de la température à laquelle ils sont soumis pendant le soudage de leurs sorties en utilisant le brasage tendre à la vague ou le fer à braser. Cette seconde édition annule et remplace la première édition parue en 2003, dont elle constitue une révision technique. Les modifications importantes par rapport à l'édition antérieure comprennent: - modification éditoriale dans le domaine d'application; - ajout de spécification de la composition chimique de la soudure sans plomb.

Polprevodniški elementi - Metode za mehansko in klimatsko preskušanje - 15. del: Odpornost proti spajkalni temperaturi za elemente, montirane v skoznjih luknjah (IEC 60749-15:2010)

Ta del IEC 60749 opisuje preskus, ki se uporablja za ugotavljanje ali inkapsulirane naprave v trdnem stanju, ki se uporabljajo za montiranje v skoznjih luknjah, kljubujejo učinkom temperature, kateri so podvržene med spajkanjem njihovih vodnikov z uporabo valovitega spajkanja ali spajkanjem železa. Da bi se vzpostavil standardni preskusni postopek za najbolj ponovljive metode, se uporablja metoda spajkanja z namakanjem zaradi pogojev te metode, ki jih je lažje nadzorovati. Ta postopek določa, ali naprave lahko prenesejo spajkalno temperaturo pri postopkih montaže plošče tiskanega vezja, ne da bi se poslabšale njihove električne značilnosti ali notranji spoji. Ta preskus je porušitveni in se lahko uporabi za kvalifikacijo, sprejemljivost lotov in kontrolo proizvoda. Ta preskus ja na splošno v skladu z IEC 60068-2-20, vendar zaradi posebnih zahtev polprevodnikov veljajo klavzule tega standarda.

General Information

Status
Published
Publication Date
09-Dec-2010
Drafting Committee
Parallel Committee
Current Stage
6060 - Document made available
Due Date
01-Mar-2011
Completion Date
10-Dec-2010

RELATIONS

Buy Standard

Standard
EN 60749-15:2011
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60749-15:2011
01-februar-2011
1DGRPHãþD
SIST EN 60749-15:2004
Polprevodniški elementi - Metode za mehansko in klimatsko preskušanje - 15. del:
Odpornost proti spajkalni temperaturi za elemente, montirane v skoznjih luknjah
(IEC 60749-15:2010)

Semiconductor devices - Mechanical and climatic test methods - Part 15: Resistance to

soldering temperature for through-hole mounted devices (IEC 60749-15:2010)
Halbleiterbauelemente - Mechanische und klimatische Prüfverfahren - Teil 15:
Beständigkeit gegen Löttemperatur bei Bauelementen zur Durchsteckmontage (IEC
60749-15:2010)

Dispositifs à semiconducteurs - Méthodes d’essai mécaniques et climatiques - Partie 15:

Résistance à la température de soudage pour dispositifs par trous traversants (CEI

60749-15:2010)
Ta slovenski standard je istoveten z: EN 60749-15:2010
ICS:
31.080.01 Polprevodniški elementi Semiconductor devices in
(naprave) na splošno general
SIST EN 60749-15:2011 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60749-15:2011
---------------------- Page: 2 ----------------------
SIST EN 60749-15:2011
EUROPEAN STANDARD
EN 60749-15
NORME EUROPÉENNE
December 2010
EUROPÄISCHE NORM
ICS 31.080.01 Supersedes EN 60749-15:2003
English version
Semiconductor devices -
Mechanical and climatic test methods -
Part 15: Resistance to soldering temperature for through-hole mounted
devices
(IEC 60749-15:2010)
Dispositifs à semiconducteurs - Halbleiterbauelemente -
Méthodes d’essai mécaniques et Mechanische und klimatische
climatiques - Prüfverfahren -
Partie 15: Résistance à la température de Teil 15: Beständigkeit gegen
soudage pour dispositifs par trous Löttemperatur bei Bauelementen zur
traversants Durchsteckmontage
(CEI 60749-15:2010) (IEC 60749-15:2010)

This European Standard was approved by CENELEC on 2010-12-10. CENELEC members are bound to comply

with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and notified

to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60749-15:2010 E
---------------------- Page: 3 ----------------------
SIST EN 60749-15:2011
EN 60749-15:2010 - 2 -
Foreword

The text of document 47/2067/FDIS, future edition 2 of IEC 60749-15, prepared by IEC TC 47,

Semiconductor devices, was submitted to the IEC-CENELEC parallel vote and was approved by

CENELEC as EN 60749-15 on 2010-12-01.
This European Standard supersedes EN 60749-15:2003.
The significant changes with respect from EN 60749-15:2003 include:
– editorial change in the scope,
– addition of lead-free solder chemical composition specification.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent

rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-09-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-12-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice

The text of the International Standard IEC 60749-15:2010 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

IEC 60068-2-20 NOTE Harmonized as EN 60068-2-20.
__________
---------------------- Page: 4 ----------------------
SIST EN 60749-15:2011
IEC 60749-15
Edition 2.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Semiconductor devices – Mechanical and climatic test methods –
Part 15: Resistance to soldering temperature for through-hole mounted devices
Dispositifs à semiconducteurs – Méthodes d’essai mécaniques et climatiques –
Partie 15: Résistance à la température de soudage pour dispositifs par trous
traversants
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX
ICS 31.080.01 ISBN 978-2-88912-231-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 5 ----------------------
SIST EN 60749-15:2011
– 2 – 60749-15 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SEMICONDUCTOR DEVICES –
MECHANICAL AND CLIMATIC TEST METHODS –
Part 15: Resistance to soldering temperature
for through-hole mounted devices
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, wh
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.