EN IEC 61439-7:2020

Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations

Clause 1 of IEC 61439-1:2011 is applicable except as follows. Replacement: NOTE 1 Throughout this document, the terms AMHS (see 3.1.701), ACCS (see 3.1.702), AMPS (see 3.1.703), AEVCS (see 3.1.7704) are used for low-voltage switchgear and controlgear assemblies intended for use respectively in marinas and similar locations (AMHS), campsites and similar locations (ACCS), market squares and other similar external public sites (AMPS) and charging stations (AEVCS). The term ASSEMBLIES is used for indicating all these boards. This Part of IEC 61439 defines the specific requirements of ASSEMBLIES as follows: - ASSEMBLIES for which the rated voltage does not exceed 1 000 V in the case of AC or 1 500 V in the case of DC; - ASSEMBLIES intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; - ASSEMBLIES operated by ordinary persons (e.g. plug and unplug of electrical equipment); - ASSEMBLIES intended to be installed and used in market squares, marinas, campsites and other similar outdoor public sites; - ASSEMBLIES intended for charging stations for electric vehicles (AEVCS) for Mode 3 and Mode 4. They are designed to integrate the functionality and additional requirements for electric vehicle conductive charging systems according to IEC 61851-1:2017. For the correct SELECTION of the switching devices and components, the following standards apply: - IEC 60364-7-709 (AMHS) OR - IEC 60364-7-708 (ACCS) OR - IEC 60364-7-740 (AMPS) OR - IEC 60364-7-722 (AEVCS). This document applies to all ASSEMBLIES whether they are designed, manufactured and verified on a one-off basis or fully standardised and manufactured in quantity. The manufacture and/or assembly may be carried out other than by the original manufacturer (see 3.10.1 of IEC 61439-1:2011). This document does not apply to individual devices and self-contained components such as circuit breakers, fuse switches, electronic equipment, which comply with their relevant product standards. NOTE 2 Where electrical equipment is directly connected to public low voltage supply system and equipped with a meter for billing of the legal provider of the low voltage supply, additional particular requirements based on national regulations apply, if any. This document does not apply to boxes and enclosures for electrical accessories for household and similar fixed electrical installations as defined in IEC 60670-24.

Niederspannungs-Schaltgerätekombinationen - Teil 7: Schaltgerätekombinationen für bestimmte Anwendungen wie Marinas, Campingplätze, Marktplätze, Ladestationen für Elektrofahrzeuge

Ensembles d’appareillage à basse tension - Partie 7: Ensembles pour installations publiques particulières telles que les marinas, les terrains de camping, les marchés et les emplacements analogues et pour bornes de charge de véhicules électriques

L’Article 1 de l’IEC 61439-1:2011 s’applique avec les exceptions suivantes. Remplacement: NOTE 1 Dans l’ensemble du présent document, les termes AMHS (voir 3.1.701), ACCS (voir 3.1.702), AMPS (voir 3.1.703), AEVCS (voir 3.1.704) sont utilisés pour désigner les ensembles d’appareillage à basse tension destinés à être utilisés respectivement dans les marinas et emplacements analogues (AMHS), terrains de camping et emplacements analogues (ACCS), marchés et autres lieux publics extérieurs analogues (AMPS), et les bornes de charge (AEVCS). Le terme ENSEMBLES est utilisé pour indiquer tous ces types de tableaux. La présente partie de l'IEC 61439 définit les exigences spécifiques applicables aux ENSEMBLES comme suit: - ENSEMBLES dont la tension assignée ne dépasse pas 1 000 V en courant alternatif ou 1 500 V en courant continu; - ENSEMBLES destinés à être utilisés avec des équipements conçus pour la production, le transport, la distribution et la conversion de l'énergie électrique et la commande des matériels consommant de l'énergie électrique; - ENSEMBLES actionnés par des personnes ordinaires (par exemple, brancher ou débrancher du matériel électrique); - ENSEMBLES destinés à être installés et utilisés dans les marchés, marinas, terrains de camping et autres lieux publics extérieurs analogues; - ENSEMBLES destinés aux bornes de charge de véhicules électriques (AEVCS) de Mode 3 et de Mode 4. Ils sont conçus pour intégrer la fonctionnalité et les exigences supplémentaires des systèmes de charge conductive pour véhicules électriques conformément à l’IEC 61851-1:2017. Pour le CHOIX approprié des appareils de connexion et des composants, les normes suivantes s'appliquent: - IEC 60364-7-709 (AMHS) OU - IEC 60364-7-708 (ACCS) OU - IEC 60364-7-740 (AMPS) OU - IEC 60364-7-722 (AEVCS). Le présent document s’applique à tous les ENSEMBLES qu’ils soient conçus, fabriqués et vérifiés à l’unité ou qu’ils soient complètement normalisés et fabriqués en quantité. La fabrication et/ou l’assemblage peuvent être réalisé(e)s par un tiers qui n'est pas le constructeur d'origine (voir 3.10.1 de l’IEC 61439-1:2011). Le présent document ne s’applique pas aux appareils pris en considération individuellement et aux composants indépendants tels que les disjoncteurs, les fusibles-interrupteurs, les matériels électroniques, qui sont conformes aux normes de produits les concernant. NOTE 2 Lorsque le matériel électrique est directement raccordé au réseau d’alimentation public à basse tension et équipé d’un compteur de facturation du prestataire légal du fournisseur de l’alimentation basse tension, des exigences particulières supplémentaires fondées sur des réglementations nationales s’appliquent, le cas échéant. Le présent document ne s’applique pas aux boîtes et enceintes pour appareillage électrique pour installations électriques fixes pour usages domestiques et analogues telles que définies dans l'IEC 60670-24.

Sestavi nizkonapetostnih stikalnih in krmilnih naprav - 7. del: Sestavi za posebno uporabo, na primer za marine, prostore za kampiranje, tržnice, napajalne postaje za električna vozila (IEC 61439-7:2018+COR1:2019)

General Information

• Status: Published
• Publication Date: 30-Apr-2020
• ICS: 29.130.20 - Low voltage switchgear and controlgear
• Technical Committee: CLC/SR 121B - Low-voltage switchgear and controlgear assemblies
• Drafting Committee: IEC/SC 121B - Low-voltage switchgear and controlgear assemblies
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 01-May-2020
• Completion Date: 01-May-2020
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Mandate: M/511 - Mandate to CEN, CENELEC and ETSI relating to harmonised standards in the field of the Low Voltage Directive
• Ref Project: SIST EN IEC 61439-7:2021 - Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations (IEC 61439-7:2018+COR1:2019)

Relations

• Replaced By: EN IEC 61439-7:2023 - Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations
• Effective Date: 22-Dec-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2021
Sestavi nizkonapetostnih stikalnih in krmilnih naprav - 7. del: Sestavi za posebno
uporabo, na primer za marine, prostore za kampiranje, tržnice, napajalne postaje
za električna vozila (IEC 61439-7:2018+COR1:2019)
Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific
applications such as marinas, camping sites, market squares, electric vehicle charging
stations (IEC 61439-7:2018+COR1:2019)
Niederspannungs-Schaltgerätekombinationen - Teil 7: Schaltgerätekombinationen für
bestimmte Anwendungen wie Marinas, Campingplätze, Marktplätze, Ladestationen für
Elektrofahrzeuge (IEC 61439-7:2018+COR1:2019)
Ensembles d’appareillage à basse tension - Partie 7: Ensembles pour installations
publiques particulières telles que les marinas, les terrains de camping, les marchés et
les emplacements analogues et pour bornes de charge de véhicules électriques (IEC
61439-7:2018+COR1:2019)
Ta slovenski standard je istoveten z: EN IEC 61439-7:2020
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61439-7

NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 29.130.20
English Version
Low-voltage switchgear and controlgear assemblies - Part 7:
Assemblies for specific applications such as marinas, camping
sites, market squares, electric vehicle charging stations
(IEC 61439-7:2018 + COR1:2019)
Ensembles d'appareillage à basse tension - Partie 7: Niederspannungs-Schaltgerätekombinationen - Teil 7:
Ensembles pour installations publiques particulières telles Schaltgerätekombinationen für bestimmte Anwendungen
que les marinas, les terrains de camping, les marchés et les wie Marinas, Campingplätze, Marktplätze, Ladestationen für
emplacements analogues et pour bornes de charge de Elektrofahrzeuge
véhicules électriques (IEC 61439-7:2018 + COR1:2019)
(IEC 61439-7:2018 + COR1:2019)
This European Standard was approved by CENELEC on 2019-01-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61439-7:2020 E

European foreword
The text of document 121B/74/FDIS, future edition 1 of IEC 61439-7, prepared by SC 121B "Low-
voltage switchgear and controlgear assemblies" of IEC/TC 121 "Switchgear and controlgear and their
assemblies for low voltage" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61439-7:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-11-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-01
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61439-7:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60364-7-708 NOTE Harmonized as HD 60364-7-708
IEC 60364-7-709 NOTE Harmonized as HD 60364-7-709
IEC 60364-7-722 NOTE Harmonized as HD 60364-7-722
IEC 60364-7-740 NOTE Harmonized as HD 60364-7-740
IEC 60670-24 NOTE Harmonized as EN 60670-24
IEC 61439-3 NOTE Harmonized as EN 61439-3
IEC 61851-1:2017 NOTE Harmonized as EN IEC 61851-1:2019 (not modified)
IEC 61851-23 NOTE Harmonized as EN 61851-23

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Clause 2 of IEC 61439-1:2011 is applicable except as follows.
Addition:
Publication Year Title EN/HD Year
IEC 60068-2-27 -  Environmental testing - Part 2-27: Tests - Test Ea EN 60068-2-27 -
and guidance: Shock
IEC 60068-2-75 -  Environmental testing - Part 2-75: Tests - Test Eh: EN 60068-2-75 -
Hammer tests
IEC 61439-1 2011 Low-voltage switchgear and controlgear EN 61439-1 2011
assemblies - Part 1: General rules

IEC 61439-7 ®
Edition 1.0 2018-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Low-voltage switchgear and controlgear assemblies –

Part 7: Assemblies for specific applications such as marinas, camping sites,

market squares, electric vehicle charging stations

Ensembles d’appareillage à basse tension –

Partie 7: Ensembles pour installations publiques particulières telles que les

marinas, les terrains de camping, les marchés et les emplacements analogues

et pour bornes de charge de véhicules électriques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.130.20 ISBN 978-2-8322-6335-8

– 2 – IEC 61439-7:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 6
4 Symbols and abbreviations . 8
5 Interface characteristics . 9
6 Information . 12
7 Service conditions . 13
8 Constructional requirements . 13
9 Performance requirements . 15
10 Design verification . 15
11 Routine verification . 24
Annexes . 25
Annex AA (informative) Items subject to agreement between the ASSEMBLY
manufacturer and the user . 26
Annex BB (informative) Design verification . 30
Annex CC (normative) Endurance of the individual switching device . 31
Annex DD (informative) Examples of ASSEMBLIES in accordance with 5.701.1.1 . 35
Annex EE (informative) List of notes concerning certain countries . 36
Bibliography . 38

Figure 701 – Diagram of test to verify the resistance to static load . 17
Figure 702 – Diagram of test to verify the mechanical strength of doors . 18
Figure 703 – Sandbag for test to verify the resistance to shock load . 19
Figure 704 – Diagram of test to verify resistance to shock load . 20
Figure 705 – Diagram of test to verify resistance to torsional stress . 22
Figure 706 – Striker element for test of resistance to mechanical shock impacts
induced by sharp-edged objects. 23
Figure CC.1 – Test circuit for endurance of the individual switching device test . 33
Figure CC.2 – Informative wave shape of inrush current for tests in accordance with
Annex CC . 34
Figure DD.1 – Examples of ASSEMBLIES according to 5.701.1.1 . 35

Table 701 – Values of assumed loading . 9
Table 702 – Mechanical tests. 11
Table AA.1 – Items subject to agreement between the ASSEMBLY manufacturer and the
user . 26
Table BB.1 – List of design verifications to be performed . 30

IEC 61439-7:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES –

Part 7: Assemblies for specific applications such as marinas, camping
sites, market squares, electric vehicle charging stations

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself doe
...