Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units

IEC 60947-3:2008 applies to switches, disconnectors, switch-disconnectors and fuse-combination units to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V a.c. or 1 500 V d.c. This part does not apply to equipment coming within the scope of IEC 60947-2, IEC 60947-4-1 and IEC 60947-5-1; however, when switches and fuse-combination units coming into the scope of this part are normally used to start, accelerate and/or stop an individual motor they shall also comply with the additional requirements given in Annex A. The requirements for single pole operated three pole switches are included in Annex C. Auxiliary switches fitted to equipment within the scope of this part shall comply with the requirements of IEC 60947-5-1. This part does not include the additional requirements necessary for electrical apparatus for explosive gas atmospheres. This edition includes the following significant technical changes with respect to the previous edition: - alignment with the fifth edition of IEC 60947-1; - a switching operation without current allowed between making and breaking operation (Table 3); - increased number of operations for AC-23 allowed with agreement of the manufacturer (Table 3); - simplified test procedure amended, f) added to 8.3.2.1.3; - temperature rise test shall be made at the rated operational current /e instead of the conventional enclosed thermal current /the (8.3.3.1).

Niederspannungsschaltgeräte - Teil 3: Lastschalter, Trennschalter, Lasttrennschalter und Schalter-Sicherungs-Einheiten

Appareillage à basse tension - Partie 3: Interrupteurs, sectionneurs, interrupteurs-sectionneurs et combinés-fusibles

La CEI 60947-3:2008 s'applique à l'appareillage suivant: interrupteurs, sectionneurs, interrupteurs-sectionneurs et combinés-fusibles, destinés à être insérés dans des circuits de distribution et des circuits de moteurs dont la tension assignée est inférieure ou égale à 1 000 V en courant alternatif ou à 1 500 V en courant continu. La présente partie n'est pas applicable au matériel faisant partie du domaine d'application de la CEI 60947-2, de la CEI 60947-4-1 et de la CEI 60947-5-1; cependant, quand les interrupteurs et les combinés-fusibles faisant partie du domaine d'application de la présente partie sont normalement utilisés pour assurer le démarrage, l'accélération et/ou l'arrêt d'un moteur, ils doivent aussi répondre aux exigences supplémentaires figurant à l'Annexe A. Les exigences pour les interrupteurs tripolaires à commande unipolaire se trouvent à l'Annexe C. Les interrupteurs auxiliaires montés sur du matériel faisant partie du domaine d'application de la présente partie doivent satisfaire aux exigences de la CEI 60947-5-1. La présente partie ne contient pas les exigences supplémentaires nécessaires au matériel électrique pour atmosphères explosives. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - alignement avec la cinquième édition de la CEI 60947-1; - une manoeuvre de commutation sans courant est admise entre une manoeuvre d'établissement et de coupure (Tableau 3); - un nombre accru de manoeuvres pour AC-23 est admis avec l'accord du fabricant (Tableau 3); - la procédure d'essai simplifiée est corrigée, le point f) a été ajouté en 8.3.2.1.3; - l'essai d'échauffement doit être réalisé au courant assigné d'emploi /e au lieu du courant thermique conventionnel sous enveloppe /the (8.3.3.1).

Nizkonapetostne stikalne in krmilne naprave - 3. del: Stikala, ločilniki, ločilna stikala in stikalni aparati z varovalkami (IEC 60947-3:2008)

Ta del standarda IEC 60947 se uporablja za stikala, ločilnike, ločilna stikala in stikalne aparate z varovalkami, ki so namenjeni uporabi v razdelilnih tokokrogih in motorskih tokokrogih, pri čemer nazivna napetost ne presega 1000 V izmenične napetosti ali 1500 V enosmerne napetosti. Proizvajalec mora določiti vrsto, mejne vrednosti in značilnosti vseh vključenih varovalk v skladu z ustreznim standardom. Ta del se ne uporablja za opremo, ki spada v področje uporabe standardov IEC 60947-2, IEC 60947-4-1 in IEC 60947-5-1; vendar morajo biti stikala in stikalni aparati z varovalkami, ki bodo spadali v področje uporabe tega dela in se običajno uporabljajo za zagon, pospeševanje in/ali ustavljanje posameznega motorja, prav tako skladni z dodatnimi zahtevami iz dodatka A. Zahteve za tripolna stikala z enim samim priključnim polom so zajete v dodatku C. Pomožna stikala, pritrjena na opremo, ki spada v področje uporabe tega dela, morajo biti skladna z zahtevami standarda IEC 60947-5-1. Ta del ne zajema dodatnih zahtev, potrebnih za električne naprave za eksplozivne plinske atmosfere.

General Information

Status
Withdrawn
Publication Date
04-Jun-2009
Withdrawal Date
30-Apr-2012
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
19-Feb-2024
Completion Date
19-Feb-2024

Relations

Buy Standard

Standard
EN 60947-3:2009
English language
62 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2009
1DGRPHãþD
SIST EN 60947-3:2000
SIST EN 60947-3:2000/A1:2002
SIST EN 60947-3:2000/A2:2006
1L]NRQDSHWRVWQHVWLNDOQHLQNUPLOQHQDSUDYHGHO6WLNDODORþLOQLNLORþLOQD
VWLNDODLQVWLNDOQLDSDUDWL]YDURYDONDPL ,(&
Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-
disconnectors and fuse-combination units (IEC 60947-3:2008)
Niederspannungsschaltgeräte - Teil 3: Lastschalter, Trennschalter, Lasttrennschalter und
Schalter-Sicherungs-Einheiten (IEC 60947-3:2008)
Appareillage à basse tension - Partie 3: Interrupteurs, sectionneurs, interrupteurs-
sectionneurs et combinés-fusibles (CEI 60947-3:2008)
Ta slovenski standard je istoveten z: EN 60947-3:2009
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60947-3
NORME EUROPÉENNE
June 2009
EUROPÄISCHE NORM
ICS 29.120.40; 29.130.20 Supersedes EN 60947-3:1999 + A1:2001 + A2:2005

English version
Low-voltage switchgear and controlgear -
Part 3: Switches, disconnectors, switch-disconnectors
and fuse-combination units
(IEC 60947-3:2008)
Appareillage à basse tension -  Niederspannungsschaltgeräte -
Partie 3: Interrupteurs, sectionneurs, Teil 3: Lastschalter, Trennschalter,
interrupteurs-sectionneurs Lasttrennschalter
et combinés-fusibles und Schalter-Sicherungs-Einheiten
(CEI 60947-3:2008) (IEC 60947-3:2008)

This European Standard was approved by CENELEC on 2009-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels

© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60947-3:2009 E
Foreword
The text of document 17B/1601/FDIS, future edition 3 of IEC 60947-3, prepared by SC 17B, Low-voltage
switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 60947-3 on 2009-05-01.
This European Standard supersedes EN 60947-3:1999 + A1:2001 + A2:2005.
– alignment with EN 60947-1:2007;
– a switching operation without current allowed between making and breaking operation (Table 3);
– increased number of operations for AC-23 allowed with agreement of the manufacturer (Table 3);
– simplified test procedure amended, f) added to 8.3.2.1.3;
– temperature rise test shall be made at the rated operational current Ie instead of the conventional
enclosed thermal current Ithe (8.3.3.1).
This part is to be used in conjunction with EN 60947-1.The numbering of the subclauses is sometimes not
continuous because it is based on EN 60947-1.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-05-01
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directive EMC (2004/108/EC). See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60947-3:2008 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60447 NOTE  Harmonized as EN 60447:2004 (not modified).
__________
- 3 - EN 60947-3:2009
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60050-441 1984 International Electrotechnical Vocabulary - -
A1 2000 (IEV) -
Chapter 441: Switchgear, controlgear and
fuses
IEC 60269 (mod) Series Low-voltage fuses EN/HD 60269 Series

IEC 60410 1973 Sampling plans and procedures - -
for inspection by attributes
IEC 60417 Data- Graphical symbols for use on equipment - -
base
IEC 60947-1 2007 Low-voltage switchgear and controlgear - EN 60947-1 2007
Part 1: General rules
IEC 60947-2 2006 Low-voltage switchgear and controlgear - EN 60947-2 2006
Part 2: Circuit-breakers
IEC 60947-4-1 2000 Low-voltage switchgear and controlgear - EN 60947-4-1 2001
A1 2002 Part 4-1: Contactors and motor-starters - A1 2002
A2 2005 Electromechanical contactors and motor- A2 2005
starters
IEC 60947-5-1 2003 Low-voltage switchgear and controlgear - EN 60947-5-1 2004
Part 5-1: Control circuit devices and switching + corr. July 2005
elements - Electromechanical control circuit
devices
1)
IEC 61000-4-2 1995 Electromagnetic compatibility (EMC) - EN 61000-4-2 1995
A1 1998 Part 4-2: Testing and measurement A1 1998
A2 2000 techniques - Electrostatic discharge A2 2001
immunity test
IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - EN 61000-4-3 2006
A1 2007 Part 4-3: Testing and measurement A1 2008
techniques - Radiated, radio-frequency, + IS1 2009
electromagnetic field immunity test

IEC 61000-4-4 2004 Electromagnetic compatibility (EMC) - EN 61000-4-4 2004
Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst
immunity test
IEC 61000-4-5 2005 Electromagnetic compatibility (EMC) - EN 61000-4-5 2006
Part 4-5: Testing and measurement
techniques - Surge immunity test

1)
EN 61000-4-2 is superseded by EN 61000-4-2:2009, which is based on IEC 61000-4-2:2008.

Publication Year Title EN/HD Year

IEC 61000-4-6 2003 Electromagnetic compatibility (EMC) -
+ A1 2004 Part 4-6: Testing and measurement
2)
+ A2 2006 techniques - Immunity to conducted EN 61000-4-6 2007
disturbances, induced by radio-frequency + corr. August 2007
fields + IS1 2009
CISPR 11 (mod) 2003 Industrial scientific and medical (ISM)
+ A1 (mod) 2004 radio-frequency equipment - EN 55011 2007
A2 2006 Electromagnetic disturbance characteristics - A2 2007
Limits and methods of measurement

CISPR 22 (mod) 2005 Information technology equipment - Radio EN 55022 2006
A1 2005 disturbance characteristics - Limits and A1 2007
3)
A2 (mod) 2006 methods of measurement A2 200X

2)
EN 61000-4-6 is superseded by EN 61000-4-6:2009, which is based on IEC 61000-4-6:2008.
3)
At draft stage.
- 5 - EN 60947-3:2009
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 1 of Annex I of the EC Directive 2004/108/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
__________
IEC 60947-3
Edition 3.0 2008-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Low-voltage switchgear and controlgear –
Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination
units
Appareillage à basse tension –
Partie 3: Interrupteurs, sectionneurs, interrupteurs-sectionneurs et combinés-
fusibles
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XA
CODE PRIX
ICS 29.120.40; 29.130.20 ISBN 2-8318-9965-6
– 2 – 60947-3 © IEC:2008
CONTENTS
FOREWORD.4
1 General .6
1.1 Scope and object.6
1.2 Normative references .7
2 Terms and definitions .8
3 Classification .11
3.1 According to the utilization category.11
3.2 According to the method of operation of manually operated equipment.11
3.3 According to suitability for isolation .11
3.4 According to the degree of protection provided.11
4 Characteristics.12
4.1 Summary of characteristics.12
4.2 Type of equipment .12
4.3 Rated and limiting values for the main circuit .12
4.4 Utilization category .14
4.5 Control circuits .15
4.6 Auxiliary circuits .15
4.7 Relays and releases .15
5 Product information.15
5.1 Nature of information .15
5.2 Marking .16
5.3 Instructions for installation, operation and maintenance.17
6 Normal service, mounting and transport conditions.17
7 Constructional and performance requirements .17
7.1 Constructional requirements .17
7.2 Performance requirements.19
7.3 Electromagnetic compatibility.22
8 Tests .24
8.1 Kind of tests .24
8.2 Type tests for constructional requirements .25
8.3 Performance.29
8.4 Electromagnetic compatibility tests .45
8.5 Special tests.46
Annex A (normative) Equipment for direct switching of a single motor.47
Annex B (informative) Items subject to agreement between manufacturer and user.53
Annex C (normative) Single pole operated three pole switches .54
Bibliography .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.