iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 55015:2006/A2:2009

(Amendment)

Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

Superseded by EN 55015:2013

Grenzwerte und Messverfahren für Funkstörungen von elektrischen Beleuchtungseinrichtungen und ähnlichen Elektrogeräten

Limites et méthodes de mesure des perturbations radioélectriques produites par les appareils électriques d'éclairage et les appareils analogues

Mejne vrednosti in postopki merjenja radijskih motenj naprav električne razsvetljave in podobne opreme (CISPR 15:2005/A2:2008)

General Information

Status
Withdrawn
Publication Date
24-Mar-2009
Withdrawal Date
29-Feb-2012
ICS
33.100.10 - Emission
Technical Committee
CLC/TC 210 - Electromagnetic Compatibility (EMC)
Drafting Committee
IEC/SC CISPR/F - IEC_SC_CISPR/F
Parallel Committee
IEC/SC CISPR/F - IEC_SC_CISPR/F
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
12-Jun-2016
Completion Date
12-Jun-2016
Directive
2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
89/336/EEC - Electromagnetic compatibility (EMC)
Mandate
M/404 - Standardisation Mandate to CEN, CENELEC and ETSI for harmonized standard according to the Electro Magnetic Compatibility (EMC) Directive 2004/108/EC
Ref Project
SIST EN 55015:2007/A2:2009 - Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

Relations

Replaced By
EN 55015:2013 - Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
Effective Date
28-Jan-2023
Amends
EN 55015:2006 - Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
Effective Date
29-Jan-2023

Buy Standard

EN 55015:2007/A2:2009EN 55015:2007/A2:2009
PreviousNext
Amendment
EN 55015:2007/A2:2009
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 55015:2007/A2:2009
01-september-2009
0HMQHYUHGQRVWLLQSRVWRSNLPHUMHQMDUDGLMVNLKPRWHQMQDSUDYHOHNWULþQH
UD]VYHWOMDYHLQSRGREQHRSUHPH &,635$
Limits and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment
Grenzwerte und Messverfahren für Funkstörungen von elektrischen
Beleuchtungseinrichtungen und ähnlichen Elektrogeräten
Limites et méthodes de mesure des perturbations radioélectriques produites par les
appareils électriques d'éclairage et les appareils analogues
Ta slovenski standard je istoveten z: EN 55015:2006/A2:2009
ICS:
33.100.10 Emisija Emission
SIST EN 55015:2007/A2:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 55015:2007/A2:2009

---------------------- Page: 2 ----------------------

SIST EN 55015:2007/A2:2009

EUROPEAN STANDARD
EN 55015/A2

NORME EUROPÉENNE
March 2009
EUROPÄISCHE NORM

ICS 33.100.10


English version


Limits and methods of measurement of radio disturbance characteristics
of electrical lighting and similar equipment
(CISPR 15:2005/A2:2008)


Limites et méthodes de mesure  Grenzwerte und Messverfahren
des perturbations radioélectriques für Funkstörungen von elektrischen
produites par les appareils électriques Beleuchtungseinrichtungen
d'éclairage et les appareils analogues und ähnlichen Elektrogeräten
(CISPR 15:2005/A2:2008) (CISPR 15:2005/A2:2008)




This amendment A2 modifies the European Standard EN 55015:2006; it was approved by CENELEC on
2009-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 55015:2006/A2:2009 E

---------------------- Page: 3 ----------------------

SIST EN 55015:2007/A2:2009
EN 55015:2006/A2:2009 - 2 -
Foreword
The text of document CISPR/F/489/FDIS, future amendment 2 to CISPR 15:2005, prepared by SC F,
Interference relating to household appliances, tools, lighting equipment and similar apparatus, of
IEC TC CISPR, International special committee on radio interference, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as amendment A2 to EN 55015:2006 on
2009-03-01.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
an identical national standard or by endorsement (dop) 2009-12-01
– latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2012-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of amendment 2:2008 to the International Standard CISPR 15:2005 was approved by CENELEC
as an amendment to the European Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 55015:2007/A2:2009
- 3 - EN 55015:2006/A2:2009
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications


Addition to Annex ZA of EN 55015:2006:

Publication Year Title EN/HD Year

CISPR 16-4-2 2003 Specification for radio disturbance and EN 55016-4-2 2004
immunity measuring apparatus and methods -
Part 4-2: Uncertainties, statistics and limit
modelling - Uncertainty in EMC
measurements

---------------------- Page: 5 ----------------------

SIST EN 55015:2007/A2:2009

---------------------- Page: 6 ----------------------

SIST EN 55015:2007/A2:2009
CISPR 15
Edition 7.0 2008-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
INTERNATIONAL SPECIAL
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 55016-2-3:2017/A2:2023(Amendment)
Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
SIST EN 55016-2-3:2017/A2:2023
  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 55036:2020/A1:2023(Amendment)
Electric and hybrid electric road vehicles - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers below 30 MHz
SIST EN IEC 55036:2020/A1:2023
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 55016-1-4:2019/A2:2023(Amendment)
Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
SIST EN IEC 55016-1-4:2019/A2:2023

No scope available

  • Amendment
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50715:2022(Main)
Electromagnetic compatibility - Radio frequency emission - Statistical considerations in the determination of compliance for mass-produced products with requirements for unwanted radio frequency emission
SIST EN 50715:2022

This document specifies statistical considerations for the evaluation of unwanted radio frequency emissions of mass-produced products. NOTE 1 It is based on CISPR TR 16-4-3. The reasons for such statistical considerations are: a) that the abatement of interference aims that the majority of the products to be approved shall not cause interference; b) that the CISPR limits should be suitable for the purpose of type approval of mass-produced products as well as approval of single-produced products; c) that to ensure compliance of mass-produced products with the CISPR limits, statistical techniques have to be applied; d) that it is important for international trade that the limits shall be interpreted in the same way in every country. Therefore, this document specifies requirements and provides guidance based on statistical techniques. EMC compliance of mass-produced products with the requirements of this document are based on the application of statistical techniques that reassure the consumer, with an 80 % degree of confidence, that 80 % of the products of a type being investigated comply with the limits for unintended radio frequency emission. This document does not define limits or measuring methods. It can be used only after measurements of unwanted radio frequency emissions have been performed according to the applicable standard for the unwanted radio frequency emissions. NOTE 2 Clause 4 gives some general requirements on the interpretation of CISPR radio disturbance limits and specifies different methods, which can be used alternatively. Clause 5 gives some specific requirements for certain product groups. NOTE 3 This document does not give a calculation method about the manufacturer’s risk, whether a type of products will be accepted during a second statistical evaluation. More information on the acceptance probability for a repeated measurement is given in CISPR TR 16 4 3, Edition 2.1, Annex D.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 55016-1-6:2015/A2:2022(Amendment)
Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-6: Radio disturbance and immunity measuring apparatus - EMC antenna calibration
SIST EN 55016-1-6:2015/A2:2022
  • Amendment
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61000-4-20:2022(Main)
Electromagnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides
SIST EN IEC 61000-4-20:2022

IEC 61000-4-20:2022 focuses on emission and immunity test methods for electrical and electronic equipment using various types of transverse electromagnetic (TEM) waveguides. These types include open structures (for example striplines and electromagnetic pulse simulators) and closed structures (for example TEM cells). These structures can be further classified as one-port, two-port, or multi-port TEM waveguides. The frequency range depends on the specific testing requirements and the specific TEM waveguide type. The object of this document is to describe  
TEM waveguide characteristics, including typical frequency ranges and equipment-under-test (EUT) size limitations;
TEM waveguide validation methods for electromagnetic compatibility (EMC) tests;
the EUT (i.e. EUT cabinet and cabling) definition;
test set-ups, procedures, and requirements for radiated emission measurements in TEM waveguides; and
test set-ups, procedures, and requirements for radiated immunity testing in TEM waveguides.  NOTE Test methods are defined in this document to measure the effects of electromagnetic radiation on equipment and the electromagnetic emissions from the equipment concerned. The simulation and measurement of electromagnetic radiation is not adequately exact for the quantitative determination of effects for all end-use installations. The test methods defined are structured for a primary objective of establishing adequate reproducibility of results at various test facilities for qualitative analysis of effects. This document does not intend to specify the tests to be applied to any particular apparatus or system(s). The main intention of this document is to provide a general basic reference for all interested product committees of the IEC. For radiated emission measurements, product committees select emission limits and measurement methods in consultation with CISPR standards. For radiated immunity testing, product committees remain responsible for the appropriate choice of immunity tests and immunity test limits to be applied to equipment within their scope. This document describes test methods that are separate from those of IEC 61000‑4‑3. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
provide information on the testing of large EUTs (including cables);
apply the work on measurement uncertainties by adapting the work completed in CISPR and TC 77 (for emissions and immunity);
update the validation procedure for the test volume regarding field uniformity and TEM mode verification;
provide information concerning two-port and four-port TEM waveguides;
add a new informative annex (Annex I) dealing with transient TEM waveguide characterization; and
add information dealing with dielectric test stands for EUTs.

  • Standard
    116 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 55025:2022(Main)
Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
SIST EN IEC 55025:2022

This document contains limits and procedures for the measurement of radio disturbances in the
frequency range of 150 kHz to 5 925 MHz. This document applies to vehicles, boats, internal
combustion engines, trailers, devices and any electronic/electrical component intended for use
in vehicles, boats, trailers and devices. Refer to International Telecommunications Union (ITU)
publications for details of frequency allocations. The limits are intended to provide protection
for on-board receivers installed (per the manufacturer’s guidelines) in a vehicle from
disturbances produced by components/modules in the same vehicle.
The receiver types to be protected are, for example, broadcast receivers (sound and television),
land mobile radio, radio telephone, amateur, citizens' radio, Satellite Navigation (GPS etc.), WiFi, V2X, and Bluetooth.
This document does not include protection of electronic control systems from radio frequency
(RF) emissions or from transient or pulse-type voltage fluctuations. These subjects are included
in ISO publications.
The limits in this document are recommended and subject to modification as agreed between
the customer (e.g. vehicle manufacturer) and the supplier (e.g. component manufacturer). This
document is also intended to be applied by vehicle manufacturers and suppliers which are to
be added and connected to the vehicle harness or to an on-board power connector after delivery
of the vehicle.
This document defines test methods for use by vehicle manufacturers and suppliers, to assist
in the design of vehicles and components and ensure controlled levels of on-board radio
frequency emissions.
The emission requirements in this document are not intended to be applicable to the intentional
transmissions from a radio transmitter as defined by the ITU including their spurious emissions.
NOTE 1 This exclusion is limited to those intended transmitter emissions, which leave the EUT as radiated
emissions and are coupled onto the wire line in the measurement setup. For conducted transmissions on frequencies
intentionally produced by the radio part of an EUT, this exclusion does not apply.
NOTE 2 It is usual for customers and suppliers to use radio regulation standards to manage the effect of spurious
emissions from a radio transmitter unless limits of spurious emission are agreed in the test plan.

  • Standard
    186 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61000-3-3:2013/A2:2021/AC:2022-01(Corrigendum)
Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16 A per phase and not subject to conditional connection
SIST EN 61000-3-3:2014/A2:2022/AC:2022

IEC Corrected version

  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61000-3-3:2013/A2:2021(Amendment)
Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16 A per phase and not subject to conditional connection
SIST EN 61000-3-3:2014/A2:2022

The contents of the corrigendum of January 2022 have been included in this copy.

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 55011:2016/A2:2021(Amendment)
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
SIST EN 55011:2016/A2:2021

2021-02-25: TC Off confirmed: can be published without link to legislation as agreed by BT D162/C064, link removed
2019-12-02: NEXT ACTION: TC to prepare ZZ
2019-12-02: TC decision to further process document
2019-01-28 - Assessment is missing.

  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day