EN 60317-0-10:2017

Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire

IEC 60317-0-10:2017 specifies the general requirements of polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated bare, grade 1 or grade 2 or enamelled round copper winding wires. The range of nominal conductor dimensions is given in Table 1, Table 2, Table A.1 and Table A.2. Keywords: insulated wires used for windings

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 0-10: Allgemeine Anforderungen – Runddrähte aus Kupfer, blank oder lackiert, mit Polyesterglasfasern umwickelt und verschmolzen, nicht lackiert oder mit Harz oder mit Lack imprägniert

Spécifications pour types particuliers de fils de bobinage - Partie 0-10: Exigences générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de vernis ou de résine

IEC 60317-0-10:2017 spécifie les exigences générales pour le fil de section circulaire en cuivre nu ou émaillé de grade 1 ou de grade 2, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de résine ou de vernis. La gamme des dimensions nominales des conducteurs est donnée dans le Tableau 1, le Tableau 2, le Tableau A.1 et le Tableau A.2. Mots clés: fils isolés utilisés pour les enroulements

Specifikacije za posebne vrste navijalnih žic - 0-10. del: Splošne zahteve - Bakrena žica z okroglim prerezom, ovita s poliesterskim steklenim vlaknom in impregnirana s silikonsko smolo ali lakom, gola ali emajlirana (IEC 60317-0-10:2017)

Ta del standarda IEC 60317 določa splošne zahteve za bakreno žico z okroglim prerezom, ovito s poliestrskim steklenim vlaknom, nepremazano ali impregnirano s smolo ali lakom, golo, razreda 1 ali 2, ali emajlirano.
Obseg nazivnih mer kondenzatorja je podan v razpredelnicah 1, 2, A.1 in A.2.

General Information

• Status: Published
• Publication Date: 03-Aug-2017
• Withdrawal Date: 07-Jun-2020
• ICS: 29.060.10 - Wires
• Technical Committee: CLC/TC 55 - Winding wires
• Drafting Committee: IEC/TC 55 - IEC_TC_55
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 04-Aug-2017
• Completion Date: 04-Aug-2017
• Ref Project: SIST EN 60317-0-10:2017 - Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester Glass fibre wound, resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-10:2017)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifikacije za posebne vrste navijalnih žic - 0-10. del: Splošne zahteve - Bakrena žica z okroglim prerezom, ovita s poliesterskim steklenim vlaknom in impregnirana s silikonsko smolo ali lakom, gola ali emajlirana (IEC 60317-0-10:2017)Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester Glass fibre wound, resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-10:2017)77.150.30Bakreni izdelkiCopper products29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-0-10:2017SIST EN 60317-0-10:2017en01-oktober-2017SIST EN 60317-0-10:2017SLOVENSKI
STANDARD



SIST EN 60317-0-10:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60317-0-10
August 2017 ICS 29.060.10
English Version
Specifications for particular types of winding wires -
Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated,
bare or enamelled round copper wire (IEC 60317-0-10:2017)
Spécifications pour types particuliers de fils de bobinage - Partie 0-10: Exigences générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de vernis ou de résine (IEC 60317-0-10:2017)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-10: Allgemeine Anforderungen -
Mit unbeschichteten Polyesterglasfasern umwickelt und verschmolzen oder mit Harz oder Lack imprägnierter blanker oder lackisolierter Runddraht aus Kupfer (IEC 60317-0-10:2017) This European Standard was approved by CENELEC on 2017-06-08. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-0-10:2017 E SIST EN 60317-0-10:2017



EN 60317-0-10:2017 2 European foreword The text of document 55/1601/FDIS, future edition 1 of IEC 60317-0-10, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-10:2017. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-03-08 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-06-08
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-0-10:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 NOTE Harmonized in EN 60264 series. IEC 60317 NOTE Harmonized in EN 60317 series. IEC 60317-70 NOTE Harmonized as EN 60317-70. IEC 60317-71 NOTE Harmonized as EN 60317-71. IEC 60317-72 NOTE Harmonized as EN 60317-72. IEC 60851-6:2012 NOTE Harmonized as EN 60851-6:2012 (not modified). SIST EN 60317-0-10:2017



EN 60317-0-10:2017 3 Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1
...