SIST EN 60317-0-10:2017
(Main)Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester Glass fibre wound, resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-10:2017)
Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester Glass fibre wound, resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-10:2017)
This part of IEC 60317 specifies the general requirements of polyester glass-fibre wound
fused, unvarnished, or resin or varnish impregnated bare, grade 1 or grade 2 or enamelled
round copper winding wires.
The range of nominal conductor dimensions is given in Table 1, Table 2, Table A.1 and
Table A.2.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 0-10: Allgemeine Anforderungen – Runddrähte aus Kupfer, blank oder lackiert, mit Polyesterglasfasern umwickelt und verschmolzen, nicht lackiert oder mit Harz oder mit Lack imprägniert
Spécifications pour types particuliers de fils de bobinage - Partie 0-10: Exigences générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de vernis ou de résine
IEC 60317-0-10:2017 spécifie les exigences générales pour le fil de section circulaire en cuivre nu ou émaillé de grade 1 ou de grade 2, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de résine ou de vernis. La gamme des dimensions nominales des conducteurs est donnée dans le Tableau 1, le Tableau 2, le Tableau A.1 et le Tableau A.2.
Mots clés: fils isolés utilisés pour les enroulements
Specifikacije za posebne vrste navijalnih žic - 0-10. del: Splošne zahteve - Bakrena žica z okroglim prerezom, ovita s poliesterskim steklenim vlaknom in impregnirana s silikonsko smolo ali lakom, gola ali emajlirana (IEC 60317-0-10:2017)
Ta del standarda IEC 60317 določa splošne zahteve za bakreno žico z okroglim prerezom, ovito s poliestrskim steklenim vlaknom, nepremazano ali impregnirano s smolo ali lakom, golo, razreda 1 ali 2, ali emajlirano.
Obseg nazivnih mer kondenzatorja je podan v razpredelnicah 1, 2, A.1 in A.2.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifikacije za posebne vrste navijalnih žic - 0-10. del: Splošne zahteve - Bakrena žica z okroglim prerezom, ovita s poliesterskim steklenim vlaknom in impregnirana s silikonsko smolo ali lakom, gola ali emajlirana (IEC 60317-0-10:2017)Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester Glass fibre wound, resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-10:2017)77.150.30Bakreni izdelkiCopper products29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-0-10:2017SIST EN 60317-0-10:2017en01-oktober-2017SIST EN 60317-0-10:2017SLOVENSKI
STANDARD
SIST EN 60317-0-10:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60317-0-10
August 2017 ICS 29.060.10
English Version
Specifications for particular types of winding wires -
Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated,
bare or enamelled round copper wire (IEC 60317-0-10:2017)
Spécifications pour types particuliers de fils de bobinage - Partie 0-10: Exigences générales - Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de vernis ou de résine (IEC 60317-0-10:2017)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-10: Allgemeine Anforderungen -
Mit unbeschichteten Polyesterglasfasern umwickelt und verschmolzen oder mit Harz oder Lack imprägnierter blanker oder lackisolierter Runddraht aus Kupfer (IEC 60317-0-10:2017) This European Standard was approved by CENELEC on 2017-06-08. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-0-10:2017 E SIST EN 60317-0-10:2017
EN 60317-0-10:2017 2 European foreword The text of document 55/1601/FDIS, future edition 1 of IEC 60317-0-10, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-10:2017. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-03-08 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-06-08
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-0-10:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 NOTE Harmonized in EN 60264 series. IEC 60317 NOTE Harmonized in EN 60317 series. IEC 60317-70 NOTE Harmonized as EN 60317-70. IEC 60317-71 NOTE Harmonized as EN 60317-71. IEC 60317-72 NOTE Harmonized as EN 60317-72. IEC 60851-6:2012 NOTE Harmonized as EN 60851-6:2012 (not modified). SIST EN 60317-0-10:2017
EN 60317-0-10:2017 3 Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60851 series
Winding wires - Test methods EN 60851 series
IEC 60851-5 2008
Winding wires - Test methods -
Part 5: Electrical properties EN 60851-5 2008
ISO 3 -
Preferred numbers - Series of preferred numbers - -
SIST EN 60317-0-10:2017
SIST EN 60317-0-10:2017
IEC 60317-0-10 Edition 1.0 2017-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires –
Part 0-10: General requirements – Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-10: Exigences générales – Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues, non vernies ou imprégnées de vernis ou de résine
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 29.060.10
ISBN 978-2-8322-4261-2
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60317-0-10:2017
– 2 – IEC 60317-0-10:2017 IEC 2017 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions, general notes and appearance . 7 3.1 Terms and definitions . 7 3.2 General notes . 8 3.2.1 Methods of test . 8 3.2.2 Winding wire . 9 3.3 Appearance . 9 4 Dimensions. 9 4.1 Conductor diameter . 9 4.2 Out of roundness of conductor . 11 4.3 Minimum increase in diameter due to the covering . 11 4.4 Maximum overall diameter . 11 5 Electrical resistance . 12 6 Elongation . 12 7 Springiness . 12 7.1 Nominal conductor diameters up to and including 1,600 mm . 12 7.2 Nominal conductor diameters over 1,600 mm . 12 8 Flexibility and adherence . 12 8.1 Mandrel winding test . 12 8.2 Adherence test . 12 9 Heat shock . 13 10 Cut-through . 13 11 Resistance to abrasion . 13 12 Resistance to solvents . 13 13 Breakdown voltage . 13 13.1 Polyester glass fibre covered bare round copper wire . 13 13.2 Polyester glass fibre covered enamelled round copper wire . 13 14 Continuity of insulation . 14 15 Temperature index . 14 16 Resistance to refrigerants . 14 17 Solderability . 14 18 Heat or solvent bonding . 14 19 Dielectric dissipation factor . 14 20 Resistance to transformer oil . 14 21 Loss of mass . 14 23 Pin hole test . 15 30 Packaging . 15 Annex A (informative)
Diameters for intermediate nominal conductor diameters (R40) . 16 Annex B (informative)
Resistance . 18 B.1 Determination of nominal resistance . 18 Annex C (informative)
High temperature failure . 19 SIST EN 60317-0-10:2017
IEC 60317-0-10:2017 IEC 2017 – 3 –
Bibliography . 20
Table 1 – Dimensional requirements of (single) polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over grade 1 or grade 2 enamelled round copper winding wire (R20) . 10 Table 2 – Dimensional requirements of (double) polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over bare, grade 1, or grade 2 enamelled round copper winding wire (R20) . 11 Table 3 – Elongation . 12 Table 4 – Mandrel winding . 12 Table 5 – Breakdown voltage for bare round copper wire . 13 Table 6 – Breakdown voltage for enamelled round copper wire . 14 Table A.1 – Diameters for single polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over grade 1 or grade 2 enamelled round copper wire (R40) . 16 Table A.2 – Diameters for double polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over bare, grade 1 or grade 2 enamelled round copper wire (R40) . 17 Table B.1 – Electrical resistance . 18
SIST EN 60317-0-10:2017
– 4 – IEC 60317-0-10:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 0-10: General requirements –
Polyester glass-fibre wound fused, unvarnished, or resin
or varnish impregnated, bare or enamelled round copper wire
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-0-10 has been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on voting 55/1601/FDIS 55/1608/RVD
Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. SIST EN 60317-0-10:2017
IEC 60317-0-10:2017 IEC 2017 – 5 –
A list of all parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires, can be found on the IEC website. The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to the specific document. At this date, the document will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
SIST EN 60317-0-10:2017
– 6 – IEC 60317-0-10:2017 IEC 2017 INTRODUCTION This part of IEC 60317
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.