EN 50143:1997/A1:2003
(Amendment)Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 000 V but not exceeding 10 000 V
Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 000 V but not exceeding 10 000 V
Superseded by EN 50143:2009
Leitungen für Leuchtröhrengeräte und Leuchtröhren-Anlagen mit einer Leerlaufspannung von über 1 000 V, aber nicht über 10 000 V
Câbles pour installations d'enseignes et de tubes à décharges lumineuses fonctionnant avec une tension à vide supérieure à 1 000 V mais ne dépassant pas 10 000 V
Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 50143:1998/A1:2004
STANDARD
januar 2004
(istoveten EN 50143:1997/A1:2003)
Cables for signs and luminous-discharge-tube installations operating from a no-load
rated output voltage exceeding 1 kV but not exceeding 10 kV
ICS 29.060.20 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 50143/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2003
ICS 29.060.20
English version
Cables for signs and luminous-discharge-tube installations
operating from a no-load rated output voltage
exceeding 1 kV but not exceeding 10 kV
Câbles pour installations d'enseignes Leitungen für Leuchtröhrengeräte
et de tubes à décharges lumineuses und Leuchtröhren-Anlagen mit einer
fonctionnant avec une tension à vide Leerlaufspannung von über 1 kV
supérieure à 1 kV mais ne dépassant pas aber nicht über 10 kV
10 kV
This amendment A1 modifies the European Standard EN 50143:1997; it was approved by CENELEC on
2003-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50143:1997/A1:2003 E
Foreword
This amendment to the European Standard EN 50143:1997 was prepared by the Technical
Committee CENELEC TC 20, Electric cables, and agreed at the Paris meeting (May 2001) to go
forward to the Unique Acceptance Procedure.
This amendment has been prepared within the regular maintenance programme.
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as A1 to EN 50143:1997 on 2003-02-01.
The following dates were fixed:
- latest date by which the amendment has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-02-01
- latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2005-02-01
__________
– 3 – EN 50143:1997/A1:2003
2 Normative references
Replace references to HD 405, HD 602 and HD 606 by the following:
EN 50265 Common test methods for cables under fire conditions – Test for resistance to
(Series) vertical flame propagation for a single insulated conductor or cable
EN 50267 Common test methods for cables under fire conditions – Tests on gases evolved
(Series) during combustion of materials from cables
EN 50268 Common test methods for cables under fire conditions – Measurement of smoke
(Series) density of cables burning under defined conditions
EN 50307 Lead and lead alloys – Lead and lead alloy sheaths and sleeves of electric cables
4 General requirements for the construction of cables
4.5 Non-metallic components of halogen free cables
Replace “HD 602” by “EN 50267-2-2”.
5 Cable types
5.1 General
Amend descriptions of cable types C2, D2 and F to read:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.