EN 60745-2-13:2007
(Main)Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws
Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws
Applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. Does not apply to chain saws for tree service as defined in ISO 11681-2, pole cutters and pruners.
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-13: Besondere Anforderungen für Kettensägen
Outils électroportatifs à moteur - Sécurité - Partie 2-13: Règles particulières pour les scies à chaîne
S'applique aux scies à chaîne destinées à couper du bois et conçues pour être utilisées par une seule personne. Cette norme ne s'applique pas aux scies à chaîne conçues pour être utilisées conjointement avec un guide-chaîne et un couteau diviseur ou de toute autre manière telle qu'avec un support ou comme une machine fixe ou transportable. Ne s'applique pas aux scies à chaîne pour l'élagage des arbres comme défini dans l'ISO 11681-2, les scies à perche et les perches élagueuses.
Varnost električnih ročnih orodij - 2-13. del: Posebne zahteve za verižne žage (IEC 60745-2-13:2006, spremenjen)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2008
1DGRPHãþD
SIST EN 50144-2-13:2002
9DUQRVWHOHNWULþQLKURþQLKRURGLMGHO 3RVHEQH]DKWHYH]DYHULåQHåDJH ,(&
VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for
chain saws
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-13: Besondere
Anforderungen für Kettensägen
Outils électroportatifs a moteur - Sécurité - Partie 2-13: Regles particulieres pour les
scies a chaîne
Ta slovenski standard je istoveten z: EN 60745-2-13:2007
ICS:
25.140.20 (OHNWULþQDRURGMD Electric tools
65.060.80 Gozdarska oprema Forestry equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60745-2-13
NORME EUROPÉENNE
June 2007
EUROPÄISCHE NORM
ICS 25.140.20; 65.060.80 Supersedes EN 50144-2-13:2002
English version
Hand-held motor-operated electric tools -
Safety -
Part 2-13: Particular requirements for chain saws
(IEC 60745-2-13:2006, modified)
Outils électroportatifs à moteur - Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-13: Règles particulières Sicherheit -
pour les scies à chaîne Teil 2-13: Besondere Anforderungen
(CEI 60745-2-13:2006, modifiée) für Kettensägen
(IEC 60745-2-13:2006, modifiziert)
This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-13:2007 E
Foreword
The text of the International Standard IEC 60745-2-13:2006, prepared by SC 61F, Safety of
hand-held motor-operated electric tools, of IEC TC 61, Safety of household and similar
electrical appliances, together with the common modifications prepared by the Technical
Committee CENELEC TC 61F, Safety of hand-held and transportable motor-operated electric tools, was
submitted to the CENELEC Unique Acceptance Procedure and was approved by CENELEC
as EN 60745-2-13 on 2007-03-01.
This European Standard supersedes EN 50144-2-13:2002.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-03-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-03-01
This standard is divided into two parts:
Part 1: General requirements which are common to most hand-held electric motor operated
tools (for the purpose of this standard referred to simply as tools) which could come
within the scope of this standard;
Part 2: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics
of these specific tools.
This European Standard has been prepared under a mandate given to CENELEC by the
European Commission and the European Free Trade Association and covers essential
requirements of EC Directive 98/37/EC (Machinery Directive), amended by Directive
98/79/EC. See Annex ZZ.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of
conforming with the essential health and safety requirements of the Directive concerned.
CEN/TC 144 is producing standards for non-electric chain saws (EN 608).
Warning: Other requirements and other EC Directives can be applicable to the products
falling within the scope of this standard.
This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.
This Part 2-13 is to be used in conjunction with EN 60745-1:2006. When this standard states
"addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted
accordingly.
Subclauses, items, tables and figures which are additional to those in Part 1 are numbered
starting from 101.
- 3 - EN 60745-2-13:2007
Subclauses, notes, tables and figures which are additional to those in IEC 60745-2-13:2006
are prefixed “Z”.
Annexes ZA and ZZ have been added by CENELEC.
NOTE In this standard the following print types are used:
- Requirements proper;
- Test specifications;
- Explanatory matter.
Endorsement notice
The text of the International Standard IEC 60745-213:2006 was approved by CENELEC as a
European Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
1 Scope
Add:
The chain saws covered by this standard are designed only to be operated with the right hand
on the rear handle and the left hand on the front handle.
2 Normative references
Replace the reference to ISO 3864-3 by:
ISO 3864-3:2006, Graphical symbols – Safety colours and safety signs – Part 3: Design
principles for graphical symbols for use in safety signs
Add:
ISO 22868:2005, Forestry machines – Noise test code for portable hand-held machines with
an internal combustion engine - Engineering method (Grade 2 accuracy)
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable, except as follows:
6.1.2.2 Replacement:
The sound power level shall be measured according to EN ISO 3744, where the acoustic
environment, instrumentation, quantities to be measured, quantities to be determined, and the
measurement procedure are specified.
The sound power level shall be given as A-weighted sound power level in dB reference 1 pW.
The A-weighted sound pressure levels, from which the sound power is to be determined, shall
be measured directly, and not calculated from frequency band data. Measurements shall be
made in a free field over a reflecting plane.
The sound power level shall be determined according to Clause 5 of EN ISO 22868, with the
test environment, measurement surface and six microphone positions specified there and in
Clause 6 of EN ISO 22868.
The A-weighted sound power level, L , shall be calculated, in accordance with 8.6 of
WA
EN ISO 3744, as follows:
S
L = L + 10lg( ) , in dB (Z101)
WA pfA
S
- 5 - EN 60745-2-13:2007
with L determined from
pfA
1 ′
0,1L
pA,i
L = 10lg 10 − K − K
pfA 1A 2A
∑
i=1
where
is the A-weighted surface sound pressure level according to EN ISO 3744
L
pfA
′ A-weighted sound pressure level measured at the i-th microphone position, in
L
pA,i
decibels
background noise correction, A-weighted
K
1A
environmental correction, A-weighted
K
2A
S area of the measurement surface, in m²
S = 1 m²
If the test environment meets the requirements of EN ISO 22868, then the environmental
correction factor K shall be considered as negligible.
2A
For the hemispherical measurement surface, the area S of the measurement surface is
calculated as follows:
S = 2π r², in m². (Z102)
where r, the radius of the hemisphere, is 4 m as specified in Clause 5 of EN ISO 22868.
6.1.2.4 Modification:
The installation and mounting conditions shall be in accordance with A.1 and A.2 of
EN ISO 22868, as far as applicable to electric chain saws.
The ambient conditions shall be as specified in 6.1 of EN ISO 22868.
6.1.2.5 Modification:
Chain saws are tested under the two operating conditions “idling” and “full load” in
accordance with A.3.1 of EN ISO 22868.
“Idling” shall be operation at no-load, with maximum speed settings.
“Full load” shall be in accordance with A.3.3 of EN ISO 22868, with maximum speed settings.
Four consecutive tests for “idling” and four for “full load” shall be carried out, with each sound
power level determined in accordance with the procedure stated in A.3.1 of EN ISO 22868.
With L and L being the average sound power levels of the two different modes of
W1 W2
operation defined above, the resulting sound power level L is calculated by:
WA
0,1L 0,1L
W1 W2
[]
L = 10 lg 10 + 10
WA
6.2.4.2 Location of the measurement
Addition:
Figure Z101 shows the positions on the front handle and rear handle.
6.2.6.3 Operating conditions
Chain saws are tested under load observing the conditions shown in Table Z101.
Table Z101 – Test conditions
Material Freshly felled softwood log of local timber, not frozen. Width of the log to
be trimmed to 75 % of the usable cutting length of the guide bar
Orientation Log to be rigidly clamped horizontally so that the centre line of the log is
at 0,6 m from the ground
Tool bit Saw chain to be as supplied or recommended by the manufacturer
Feed force
Sufficient force, using the spiked bumper, to achieve rated input ± 10 %
Test cycle Cutting across the width of the log in a part substantially free of knots
6.2.7.2 Declaration of the vibration emission value
Addition:
The vibration emission value a of the handle with the highest emission and the uncertainty K
h
shall be declared.
8 Marking and instructions
8.12.1.1
nd
Remove the note after the 2 indent.
21 Construction
Add the following subclause:
21.Z1 This subclause of Part 1 is not applicable.
- 7 - EN 60745-2-13:2007
Add the following new figure:
Figure Z101 - Position of transducers
Add the following annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
NOTE Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
Publication Year Title EN/HD Year
ISO 3864-3 2006 Graphical symbols - Safety colours and - -
safety signs -
Part 3: Design principles for graphical
symbols for use in safety signs
ISO 6533 2001 Forestry machinery - Portable chain-saw - -
front hand-guard - Dimensions and
clearances
ISO 6534 1992 Portable chain-saw - Hand-guards - - -
Mechanical strength
ISO 7914 2002 Forestry machinery - Portable chain-saws - - -
Minimum handle clearance and sizes
ISO 7915 1991 Forestry machinery - Portable chain-saws - - -
Determination of handle strength
ISO 8334 1985 Forestry machinery - Portable chain-saws - - -
Determination of balance
ISO 9518 1998 Forestry machinery - Portable chain-saws - - -
Kickback test
ISO 17026 1992 Portable chain saws - Chain catcher - - -
Dimensions and mechanical strength
ISO 11681-2 1998 Machinery for forestry - Portable chain- EN ISO 11681-2 1998
saws - Safety requirements and testing -
Part 2: Chain-saws for tree service
ISO 22868 2005 Forestry machines - Noise test code for EN ISO 22868 2005
portable hand-held machines with an
internal combustion engine - Engineering
method (Grade 2 accuracy)
- 9 - EN 60745-2-13:2007
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the
European Commission and the European Free Trade Association and within its scope the
standard covers all relevant essential requirements as given in EC Directive 98/37/EC
(Machinery Directive), amended by Directive 98/79/EC.
Compliance with this standard provides one means of conformity with the relevant essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products
falling within the scope of this standard.
__________
NORME CEI
INTERNATIONALE
IEC
60745-2-13
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2006-03
Outils électroportatifs à moteur –
Sécurité –
Partie 2-13:
Règles particulières pour les scies à chaîne
Hand-held motor-operated electric tools –
Safety –
Part 2-13:
Particular requirements for chain saws
IEC 2006 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
V
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
60745-2-13 IEC:2006 – 3 –
CONTENTS
FOREWORD.7
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.