iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60079-32-2:2015

(Main)

Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests

Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests

IEC 60079-32-2:2015 describes test methods concerning the equipment, product and process properties necessary to avoid ignition and electrostatic shock hazards arising from static electricity. It is intended for use in a risk assessment of electrostatic hazards or for the preparation of product family or dedicated product standards for electrical or non-electrical machines or equipment. The purpose of this part of IEC 60079 is to provide standard test methods used for the control of static electricity, such as surface resistance, earth leakage resistance, powder resistivity, liquid conductivity, capacitance and evaluation of the incendivity of provoked discharges. It is especially intended for use with existing standards of the IEC 60079 series. This part of IEC 60079 presents the latest state of knowledge which may, however, slightly differ from requirements in other standards, especially concerning test climates. When a requirement of this standard conflicts with a requirement specified in IEC 60079-0, to avoid the possibility of re-testing previously approved equipment, the requirement in IEC 60079-0 applies only for equipment within the scope of IEC 60079-0. In all other cases, the statements in this part of IEC 60079 apply. Keywords: ignition and electrostatic shock hazards, static electricity

Explosionsgefährdete Bereiche - Teil 32-2: Elektrostatische Gefährdungen - Prüfverfahren

Atmosphères explosives - Partie 32-2: Dangers électrostatiques - Essais

L'IEC 60079-32-2:2015 décrit les méthodes d'essai relatives aux matériels, au produit et aux propriétés de processus nécessaires pour éviter l'inflammation et les dangers de chocs électrostatiques liés à l'électricité statique. Elle est destinée à être utilisée dans le cadre d'une évaluation des risques de dangers électrostatiques ou de la préparation de normes de famille de produits ou de normes de produits spécifiques concernant des machines ou des matériels électriques ou non électriques. Le but de la présente partie de l'IEC 60079 est de fournir des méthodes d'essai normalisées utilisées pour le contrôle de l'électricité statique, telles que la résistance superficielle, la résistance de fuite à la terre, la résistivité de la poudre, la conductivité du liquide, la capacité et l'évaluation de l'inflammabilité des décharges provoquées. Le présent document est notamment destiné à être utilisé avec les normes existantes de la série IEC 60079. La présente partie de l'IEC 60079 décrit l'état des connaissances les plus récentes qui peuvent toutefois différer légèrement des exigences d'autres normes, notamment concernant les climats d'essai. Lorsqu'une exigence de la présente norme est en contradiction avec une exigence spécifiée dans l'IEC 60079-0, cette dernière s'applique uniquement aux matériels relevant du domaine d'application de l'IEC 60079-0 pour éviter toute possibilité de contre-essai des matériels précédemment approuvés. Dans tous les autres cas, les énoncés de la présente partie de l'IEC 60079 s'appliquent. Mots clés: l'inflammation et les dangers de chocs électrostatiques, l'électricité statique

Eksplozivne atmosfere - 32-2. del: Elektrostatične nevarnosti - Preskusi (IEC 60079-32-2:2015)

General Information

Status
Published
Publication Date
23-Apr-2015
Withdrawal Date
31-Mar-2018
ICS
29.260.20 - Electrical apparatus for explosive atmospheres
Technical Committee
CLC/TC 31 - Electrical apparatus for explosive atmospheres - General requirements
Drafting Committee
IEC/TC 31 - Electrical apparatus for potentially explosive atmospheres
Current Stage
6060 - Document made available - Publishing
Start Date
24-Apr-2015
Completion Date
24-Apr-2015
Ref Project
SIST EN 60079-32-2:2015 - Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests (IEC 60079-32-2:2015)

Buy Standard

EN 60079-32-2:2015EN 60079-32-2:2015
PreviousNext
Standard
EN 60079-32-2:2015
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60079-32-2:2015
01-julij-2015
(NVSOR]LYQHDWPRVIHUHGHO(OHNWURVWDWLþQHQHYDUQRVWL3UHVNXVL ,(&

Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests (IEC 60079-32-
2:2015)
Explosionsgefährdete Bereiche - Teil 32-2: Elektrostatische Gefährdungen -
Prüfverfahren (IEC 60079-32-2:2015)
Atmosphères explosives - Partie 32-2: Dangers électrostatiques - Essais (IEC 60079-32-
2:2015)
Ta slovenski standard je istoveten z: EN 60079-32-2:2015
ICS:
29.260.20 (OHNWULþQLDSDUDWL]D Electrical apparatus for
HNVSOR]LYQDR]UDþMD explosive atmospheres
SIST EN 60079-32-2:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60079-32-2:2015

---------------------- Page: 2 ----------------------

SIST EN 60079-32-2:2015


EUROPEAN STANDARD EN 60079-32-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2015
ICS 29.260.20

English Version
Explosive atmospheres - Part 32-2: Electrostatics hazards -
Tests
(IEC 60079-32-2:2015)
Atmosphères explosives - Partie 32-2: Dangers Explosionsgefährdete Bereiche - Teil 32-2: Elektrostatische
électrostatiques - Essais Gefährdungen - Prüfverfahren
(IEC 60079-32-2:2015) (IEC 60079-32-2:2015)
This European Standard was approved by CENELEC on 2015-04-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60079-32-2:2015 E

---------------------- Page: 3 ----------------------

SIST EN 60079-32-2:2015
EN 60079-32-2:2015 - 2 -
Foreword
The text of document 31/1164/FDIS, future edition 1 of IEC 60079-32-2, prepared by IEC/TC 31 "Equipment
for explosive atmospheres" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC
as EN 60079-32-2:2015.

The following dates are fixed:
• latest date by which the document has to be (dop) 2016-01-01
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-04-01
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60079-32-2:2015 was approved by CENELEC as a European
Standard without any modification.
IEC 60079-1 NOTE Harmonized as EN 60079-1.
IEC 60079-7 NOTE Harmonized as EN 60079-7.
IEC 60079-10-1 NOTE Harmonized as EN 60079-10-1.
IEC 60079-10-2 NOTE Harmonized as EN 60079-10-2.
IEC 60167 NOTE Harmonized as HD 568 S1.
IEC 61340-4-1 NOTE Harmonized as EN 61340-4-1.
IEC 61340-4-3 NOTE Harmonized as EN 61340-4-3.
IEC 61340-4-5 NOTE Harmonized as EN 61340-4-5.
ISO 284 NOTE Harmonized as EN ISO 284.
ISO 8031 NOTE Harmonized as EN ISO 8031.
ISO 8330 NOTE Harmonized as EN ISO 8330.

---------------------- Page: 4 ----------------------

SIST EN 60079-32-2:2015
- 3 - EN 60079-32-2:2015

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an Internation
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60079-31:2024(Main)
Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
SIST EN 60079-31:2024

IEC 60079-31:2022 is available as IEC 60079-31:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60079-31:2022 is applicable to equipment protected by enclosure and surface temperature limitation for use in explosive dust atmospheres. It specifies requirements for design, construction and testing of Ex Equipment and Ex Components. This document supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this document conflicts with a requirement of IEC 60079-0, the requirement of this document takes precedence. This document does not apply to dusts of explosives, which do not require atmospheric oxygen for combustion, or to pyrophoric substances. This document does not apply to Ex Equipment or Ex Components intended for use in underground parts of mines as well as those parts of surface installations of such mines endangered by firedamp and/or combustible dust. This document does not take account of any risk due to an emission of flammable or toxic gas from the dust. This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision. Main significant changes from the previous edition are: 1) Document has been restructured from edition 2 2) Fault current rating of interrupting contacts in clauses 4.3.1 and 4.4.1, major change type C1 3) Cells and batteries in clauses 4.3.5.1 and 4.4.5.1, major change type C2 4) Overload or malfunction condition for the determination of temperature class for "tb" converter fed rotating electric machines, major change type C3 5) Additional requirements for entry devices with dust ignition protection by enclosure "t", major change type C4 Information about the background of ‘Major Technical Changes’ C1 – Ex Equipment having Level of Protection "ta" shall be rated for connection to a circuit with a prospective short circuit current of not greater than 1.5 kA. For Ex Equipment having Level of Protection "tb" or "tc" which is intended for mains connection and intended to interrupt fault current above 10kA, the equipment shall have a rated maximum short circuit withstand current, be tested according to 6.1.1.1, and be marked according to Clause 7. C2 – For Ex Equipment having Level of Protection "ta" which contains a cell or battery, only a sealed cell or battery shall be used. For Ex Equipment having Level of Protection "tb" and "tc" where there are sparking contacts or hot surfaces, and which contains a cell or battery, only a sealed cell or battery shall be used. C3 – Table 2 now includes malfunction conditions for temperature class determination of Level of Protection "tb" converter-fed electric machines. C4 – Annex A added for entry devices with Type of Protection "t" including cable transit devices.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60079-17:2024(Main)
Explosive atmospheres - Part 17: Electrical installations inspection and maintenance
SIST EN IEC 60079-17:2024

This part of the IEC 60079 series applies to users and covers only those factors directly related to the inspection and maintenance of electrical installations specifically designed for hazardous areas, where the hazard may be caused by explosive gas or explosive dust atmospheres. It does not include: - other fundamental installation and inspection requirements for electrical installations; - the verification of electrical equipment; - protection or ventilation of rooms; - gas detection systems; - the repair and overhaul of explosion protected equipment (see IEC 60079-19). While this standard does not include inspection of safety devices such as used in ventilated rooms (see 60079-13), this standard does include the requirements for inspection and maintenance of individual items of equipment that will be part of such systems, for example motors or sensors. This standard supplements the requirements for inspection and testing in non-hazardous areas in IEC 60364-6. NOTE 1 Standards applied at the date of installation might not have been IEC standards. This standard is intended to be applied where there can be a risk due to the presence of explosive gas or dust mixtures with air or combustible dust layers under normal atmospheric conditions. It does not apply to: - underground mining areas, - dusts of explosives, - pyrophoric substances.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60079-25:2022/AC:2022-12(Corrigendum)
Explosive atmospheres - Part 25: Intrinsically safe electrical systems
SIST EN IEC 60079-25:2022/AC:2023

IEC Corrected version

  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62990-1:2022(Main)
Workplace atmospheres - Part 1: Gas detectors - Performance requirements of detectors for toxic gases
SIST EN IEC 62990-1:2023

This part of IEC 62990 specifies general requirements for design, function and performance, and describes the test methods that apply to portable, transportable, and fixed equipment for the detection and concentration measurement of toxic gases and vapours in workplace atmospheres and other industrial and commercial applications. This document is applicable to continuously sensing equipment whose primary purpose is to provide an indication, alarm and/or other output function the purpose of which is to indicate the presence of a toxic gas or vapour in the atmosphere and in some cases to initiate automatic or manual protective action(s). It is applicable to equipment in which the sensor generates an electrical signal when gas is present. This document applies to two types of equipment: - Type HM (Health Monitoring) ‘occupational exposure’ equipment: For occupational exposure measurement, the performance requirements are focused on uncertainty of measurement of gas concentrations in the region of Occupational Exposure Limit Values (OELV). The upper limit of measurement will be defined by the manufacturer in accordance with 4.2.1. - Type SM (Safety Monitoring) ‘general gas detection’ equipment: For general gas detection applications (e.g. safety warning, leak detection), the performance requirements are focused on alarm signalling. The upper limit of measurement will be defined by the manufacturer according to the intended use of the equipment. In general, the requirements for accuracy will be higher for Type HM equipment than for Type SM equipment. The same equipment may meet the requirements of both Type HM and Type SM. For equipment used for sensing the presence of multiple gases this document applies only to the detection of toxic gas or vapour. This document is not applicable to equipment: - with samplers and concentrators such as sorbents or paper tape having an irreversible indication; - used for the measurement of gases and vapours related to the risk of explosion; - used for the measurement of oxygen; – used only in laboratories for analysis or measurement; - used only for process measurement purposes; - used in the domestic environment; - used in environmental air pollution monitoring; - used for open-path (line of sight) area gas measurement; - used for ventilation control in car parks or tunnels.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62990-1:2022/A11:2022(Amendment)
Workplace atmospheres - Part 1: Gas detectors - Performance requirements of detectors for toxic gases
SIST EN IEC 62990-1:2023/A11:2023

This part of IEC 62990 specifies general requirements for design, function and performance, and describes the test methods that apply to portable, transportable, and fixed equipment for the detection and concentration measurement of toxic gases and vapours in workplace atmospheres and other industrial and commercial applications. This document is applicable to continuously sensing equipment whose primary purpose is to provide an indication, alarm and/or other output function the purpose of which is to indicate the presence of a toxic gas or vapour in the atmosphere and in some cases to initiate automatic or manual protective action(s). It is applicable to equipment in which the sensor generates an electrical signal when gas is present. This document applies to two types of equipment: • Type HM (Health Monitoring) ‘occupational exposure’ equipment: For occupational exposure measurement, the performance requirements are focused on uncertainty of measurement of gas concentrations in the region of Occupational Exposure Limit Values (OELV). The upper limit of measurement will be defined by the manufacturer in accordance with 4.2.1. • Type SM (Safety Monitoring) ‘general gas detection’ equipment: For general gas detection applications (e.g. safety warning, leak detection), the performance requirements are focused on alarm signalling. The upper limit of measurement will be defined by the manufacturer according to the intended use of the equipment. In general, the requirements for accuracy will be higher for Type HM equipment than for Type SM equipment. The same equipment may meet the requirements of both Type HM and Type SM. For equipment used for sensing the presence of multiple gases this document applies only to the detection of toxic gas or vapour. This document is not applicable to equipment: - with samplers and concentrators such as sorbents or paper tape having an irreversible indication; - used for the measurement of gases and vapours related to the risk of explosion; - used for the measurement of oxygen; – used only in laboratories for analysis or measurement; - used only for process measurement purposes; - used in the domestic environment; - used in environmental air pollution monitoring; - used for open-path (line of sight) area gas measurement; - used for ventilation control in car parks or tunnels.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60079-25:2022(Main)
Explosive atmospheres - Part 25: Intrinsically safe electrical systems
SIST EN IEC 60079-25:2022

IEC 60079-25:2020 contains the specific requirements for design, construction and assessment of intrinsically safe systems, Type of Protection “i”, intended for use, as a whole or in part, in locations in which the use of Group I, II or III Ex Equipment is required. This document supplements and modifies the general requirements of IEC 60079-0 and the intrinsic safety standard IEC 60079-11. Where a requirement of this standard conflicts with a requirement of IEC 60079-0 or IEC 60079-11, the requirement of this standard takes precedence. The installation requirements of Group II or Group III systems designed in accordance with this standard are specified in IEC 60079-14. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60079-29-1:2016/A11:2022(Amendment)
Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases
SIST EN 60079-29-1:2017/A11:2022

EN 60079-29-1 specifies general requirements for construction, testing and performance, and describes the test methods that apply to portable, transportable and fixed equipment for the detection and measurement of flammable gas or vapour concentrations with air. The equipment, or parts thereof, is intended for use in explosive atmospheres and in mines susceptible to firedamp. EN 60079-29-1 is applicable to flammable gas detection equipment with a measuring range up to any volume fraction as declared by the manufacturer, and which is intended to provide an indication, alarm or other output function; the purpose of which is to indicate a potential explosion hazard and in some cases, to initiate automatic or manual protective action(s).

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60079-29-1:2016/A1:2022(Amendment)
Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases
SIST EN 60079-29-1:2017/A1:2022

NEXT ACTION: TB ACTION BY 2020-01-31 (prep doc for BT meeting - Feb2021)
BT CONSULTATION FAILED (addition of Annex ZZ) ON 2020-11-10
HAS CONSULTANT ASSESSMENT BY 2020-09-24 (PUB assessment) - Compliant assessment on 2020-09-22
2020-04-8 mah: Consultant assessment at FV missing, Annex ZZ did not go to FV.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62990-2:2021(Main)
Workplace atmospheres - Part 2: Gas detectors - Selection, installation, use and maintenance of detectors for toxic gases and vapours
SIST EN IEC 62990-2:2021

IEC 62990-2:2021 gives guidance on the selection, installation, use and maintenance of electrical equipment used for the measurement of toxic gases and vapours in workplace atmospheres. The primary purpose of such equipment is to ensure safety of personnel and property by providing an indication of the concentration of a toxic gas or vapour and warning of its presence. This document is applicable to equipment whose purpose is to provide an indication, alarm or other output function to give a warning of the presence of a toxic gas or vapour in the atmosphere and in some cases to initiate automatic or manual protective actions. It is applicable to equipment in which the sensor automatically generates an electrical signal when gas is present. For the purposes of this document, equipment includes: a) fixed equipment; b) transportable equipment, and c) portable equipment. This document is intended to cover equipment defined within IEC 62990-1, but can provide useful information for equipment not covered by that document.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC IEC/TS 60079-47:2021(Main)
Explosive atmospheres - Part 47: Equipment protection by 2-wire intrinsically safe Ethernet concept (2-WISE)
SIST-TS CLC IEC/TS 60079-47:2021

This part of IEC 60079, which is a technical specification, specifies requirements for the construction, marking, and documenting of apparatus, systems and installations for use with the 2-Wire Intrinsically Safe Ethernet concept (2-WISE). The physical layer specification for 2-wire Ethernet 10BASE-T1L is defined in IEEE 802.3cg 2-WISE is the 2-Wire Intrinsically Safe Ethernet concept for advance physical layer (APL), designed to simplify the examination process for components and cable Entity Parameters within APL segments. This is achieved by defining universal Entity Parameter limits for APL ports, according to location and type of hazardous atmosphere, and listing a concise set of rules for the segment setup. The requirements for construction and installation of 2-WISE apparatus and systems are included in IEC 60079-11, IEC 60079-14, and IEC 60079-25, except as modified by this technical specification. Parts of a 2-WISE apparatus may be protected by any Type of Protection listed in IEC 60079-0 appropriate to the EPL for the intended use. In these circumstances, the requirements of this technical specification apply only to intrinsically safe circuits of the apparatus.

  • Technical specification
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day