Compression and mechanical connectors for power cables - Part 1-2: Test methods and requirements for insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV) tested on insulated conductors

This part of EN 61238 applies to insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV), for example according to HD 603 or other buried cables and cables installed in buildings, having a) conductors complying with EN 60228 having nominal cross-sectional areas between 2,5 mm2 and 300 mm2 for copper and between 16 mm2 and 500 mm2 for aluminium, b) a maximum continuous cable temperature not exceeding the insulation material properties. This document is not applicable to connectors for overhead line conductors nor to connectors with a sliding contact. The object of this document is to define the type test methods and requirements, which apply to insulation piercing connectors for power cables with copper or aluminium conductors. The reference method is to perform the tests on unused insulated conductors.

Pressverbinder und Schraubverbinder für Starkstromkabel – Teil 1-2: Prüfverfahren für und Anforderungen an isolationsdurchdringende Verbinder für Starkstromkabel für Nennspannungen bis zu 1 kV (Um = 1,2 kV), geprüft an isolierten Leitern

Raccords sertis et à serrage mécanique pour câbles d'énergie - Partie 1-2: Méthodes et exigences d'essai relatives aux raccords à perforation d'isolant pour câbles d'énergie de tensions assignées inférieures ou égales à 1kV (Um = 1,2 kV) soumis à essai sur des condcteurs isolés

L’IEC 61238-1-2:2018 est applicable aux raccords à perforation d’isolant pour câbles d'énergie de tensions assignées inférieures ou égales à 1 kV (Um = 1,2 kV), par exemple pour les câbles définis dans l’IEC 60502-1 ou d’autres câbles enterrés et ceux installés à l'intérieur des bâtiments, ayant a) des âmes conformes à l’IEC 60228, de section nominale comprise entre 2,5 mm2 et 300 mm2 pour le cuivre et entre 16 mm2 et 500 mm2 pour l’aluminium, b) une température maximale de fonctionnement en service permanent ne dépassant pas les propriétés du matériau isolant. Le présent document n'est pas applicable aux raccords pour conducteurs de ligne aérienne ni aux raccords équipés d’un contact glissant. L'objet du présent document est de définir les méthodes d'essais de type et les exigences qui s’appliquent aux raccords à perforation d’isolant utilisables sur les câbles d'énergie à conducteurs en cuivre ou en aluminium. La méthode de référence consiste à réaliser les essais sur des conducteurs isolés neufs. Cette première édition, conjointement avec l'IEC 61238-1-1 et l'IEC 61238-1-3, annule et remplace l'IEC 61238-1:2003. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'IEC 61238-1:2003: a) Le domaine d’application a été élargi pour couvrir les raccords de connexion pour âmes jusqu’à 2,5 mm2 (précédemment 10 mm2); il a été limité à 300 mm2 pour les âmes en cuivre et à 500 mm2 pour les âmes en aluminium car les expériences et applications d’essai des raccords à perforation d’isolant sont rares pour les âmes de fortes sections. b) Une nouvelle classe mécanique a été introduite pour répondre à la demande concernant les raccords qui ne sont soumis à aucune force mécanique. c) La méthode de réalisation de l’essai électrique a été mise à jour afin de prendre en compte la température des conducteurs de référence isolés. d) Pour l’essai de court-circuit, la méthode de calcul et les exigences ont été mises à jour. e) Pour l’essai mécanique, les méthodes et exigences ont été mises à jour. f) Des propositions d’essai différentes pour les essais sur les raccords multipolaires ont été introduites. g) Une proposition d’essai applicable au préconditionnement, utilisant une connexion en charge pour les raccords à perforation d’isolant, a été introduite.

Stisljivi in vijačni konektorji za električne kable - 1-2. del: Preskusne metode in zahteve za prebodne konektorje za električne kable za naznačene napetosti do 1 kV (Um = 1,2 kV), preskušene na izoliranih vodnikih (IEC 61238-1-2:2018)

Ta del standarda EN 61238 se uporablja za prebodne konektorje za električne kable za naznačene napetosti do 1 kV (Um = 1,2 kV), na primer za kable v skladu s standardom HD 603 ali druge v zemljo položene kable in kable, vgrajene v stavbah, ki imajo:
a) vodnike, ki so skladni s standardom EN 60228 ter imajo nominalni premer med 2,5 mm2 in 300 mm2, če so bakreni, ter med 16 mm2 in 500 mm2, če so aluminijasti;
b) največjo enakomerno temperaturo kabla, ki ne presega lastnosti izolacijskega materiala.
Ta dokument se ne uporablja za konektorje vodnikov nadzemnih vodov ali za konektorje z drsnimi kontakti.  
Namen tega dokumenta je opredeliti metode in zahteve tipskih preskusov, ki se uporabljajo za prebodne konektorje za električne kable z bakrenimi ali aluminijastimi vodniki. Referenčna metoda je namenjena za izvajanje preskusov na neuporabljenih izoliranih vodnikih.

General Information

Status
Published
Publication Date
19-Sep-2019
Withdrawal Date
18-Jul-2022
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
20-Sep-2019
Due Date
04-Dec-2020
Completion Date
20-Sep-2019

Relations

Buy Standard

Standard
EN IEC 61238-1-2:2019
English language
58 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN IEC 61238-1-2:2019
English language
58 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61238-1-2:2019
01-december-2019
Nadomešča:
SIST EN 61238-1:2004
Stisljivi in vijačni konektorji za električne kable - 1-2. del: Preskusne metode in
zahteve za prebodne konektorje za električne kable za naznačene napetosti do 1
kV (Um = 1,2 kV), preskušene na izoliranih vodnikih (IEC 61238-1-2:2018)
Compression and mechanical connectors for power cables - Part 1-2: Test methods and
requirements for insulation piercing connectors for power cables for rated voltages up to
1 kV (Um = 1,2 kV) tested on insulated conductors (IEC 61238-1-2:2018)
Pressverbinder und Schraubverbinder für Starkstromkabel – Teil 1-2: Prüfverfahren für
und Anforderungen an isolationsdurchdringende Verbinder für Starkstromkabel für
Nennspannungen bis zu 1 kV (Um = 1,2 kV), geprüft an isolierten Leitern (IEC 61238-1-
2:2018)
Raccords sertis et à serrage mécanique pour câbles d'énergie - Partie 1-2: Méthodes et
exigences d'essai relatives aux raccords à perforation d'isolant pour câbles d'énergie de
tensions assignées inférieures ou égales à 1kV (Um = 1,2 kV) soumis à essai sur des
condcteurs isolés (IEC 61238-1-2:2018)
Ta slovenski standard je istoveten z: EN IEC 61238-1-2:2019
ICS:
29.060.20 Kabli Cables
29.120.20 Spojni elementi Connecting devices
SIST EN IEC 61238-1-2:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61238-1-2:2019

---------------------- Page: 2 ----------------------
SIST EN IEC 61238-1-2:2019


EUROPEAN STANDARD EN IEC 61238-1-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2019
ICS 29.060.20 Supersedes EN 61238-1:2003 (partially) and all of its
amendments and corrigenda (if any)
English Version
Compression and mechanical connectors for power cables -
Part 1-2: Test methods and requirements for insulation piercing
connectors for power cables for rated voltages up to 1 kV (U =
m
1,2 kV) tested on insulated conductors
(IEC 61238-1-2:2018)
Raccords sertis et à serrage mécanique pour câbles Pressverbinder und Schraubverbinder für Starkstromkabel -
d'énergie - Partie 1-2: Méthodes et exigences d'essai Teil 1-2: Prüfverfahren für und Anforderungen an
relatives aux raccords à perforation d'isolant pour câbles isolationsdurchdringende Verbinder für Starkstromkabel für
d'énergie de tensions assignées inférieures ou égales à Nennspannungen bis zu 1 kV (U = 1,2 kV), geprüft an
m
1kV (U = 1,2 kV) soumis à essai sur des condcteurs isolés isolierten Leitern
m
(IEC 61238-1-2:2018) (IEC 61238-1-2:2018)
This European Standard was approved by CENELEC on 2019-07-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61238-1-2:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61238-1-2:2019
EN IEC 61238-1-2:2019 (E)

European foreword
This document (EN IEC 61238-1-2:2019) consists of the text of IEC 61238-1-2:2018 prepared by
IEC/TC 20 "Electric cables".
The following dates are fixed:
• latest date by which this document has to be (dop) 2020-07-19
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) 2022-07-19
conflicting with this document have to be
withdrawn
This document partially supersedes EN 61238-1:2003 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CENELE
...

SLOVENSKI STANDARD
oSIST prEN IEC 61238-1-2:2019
01-januar-2019
6WLVOMLYLLQYLMDþQLNRQHNWRUML]DHOHNWURHQHUJHWVNHNDEOHGHO3UHVNXVQH
PHWRGHLQ]DKWHYH]DSUHERGQHNRQHNWRUMH]DHOHNWURHQHUJHWVNHNDEOH]
QD]QDþHQLPLQDSHWRVWPLGRN9 8P N9 SUHVNXãHQHQDL]ROLUDQLKYRGQLNLK
,(&
Compression and mechanical connectors for power cables - Part 1-2: Test methods and
requirements for insulation piercing connectors for power cables for rated voltages up to
1 kV (Um = 1,2 kV) tested on insulated conductors (IEC 61238-1-2:2018)
Raccords sertis et à serrage mécanique pour câbles d'énergie - Partie 1-2: Méthodes et
exigences d'essai relatives aux raccords à perforation d'isolant pour câbles d'énergie de
tensions assignées inférieures ou égales à 1kV (Um = 1,2 kV) soumis à essai sur des
condcteurs isolés (IEC 61238-1-2:2018)
Ta slovenski standard je istoveten z: prEN IEC 61238-1-2:2018
ICS:
29.060.20 Kabli Cables
29.120.20 Spojni elementi Connecting devices
oSIST prEN IEC 61238-1-2:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 61238-1-2:2019

---------------------- Page: 2 ----------------------
oSIST prEN IEC 61238-1-2:2019


EUROPEAN STANDARD DRAFT
prEN IEC 61238-1-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

November 2018
ICS

English Version
Compression and mechanical connectors for power cables -
Part 1-2: Test methods and requirements for insulation piercing
connectors for power cables for rated voltages up to 1 kV (Um =
1,2 kV) tested on insulated conductors
(IEC 61238-1-2:2018)
Raccords sertis et à serrage mécanique pour câbles To be completed
d'énergie - Partie 1-2: Méthodes et exigences d'essai (IEC 61238-1-2:2018)
relatives aux raccords à perforation d'isolant pour câbles
d'énergie de tensions assignées inférieures ou égales à
1kV (Um = 1,2 kV) soumis à essai sur des condcteurs
isolés
(IEC 61238-1-2:2018)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2019-02-15.

The text of this draft consists of the text of IEC 61238-1-2:2018 (20/1789/FDIS).

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 67147 Ref. No. prEN IEC 61238-1-2:2018 E

---------------------- Page: 3 ----------------------
oSIST prEN IEC 61238-1-2:2019
prEN IEC 61238-1-2:2018 (E)
European foreword
This document (prEN IEC 61238-1-2:2018) consists of the text of IEC 61238-1-2:2018
prepared by IEC/TC 20 "Electric cables".
This document is currently submitted to the enquiry.
The following dates are proposed:
• latest date by which the existence of (doa) dor + 6 months
this document has to be announced at
national level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication
of an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)

2

---------------------- Page: 4 ----------------------
oSIST prEN IEC 61238-1-2:2019
Annex ZA
(normative)
Normative references to international public
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.