iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50126-1:2017/FprA1:2024

(Amendment)

Railway applications - The specification and demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS process

Railway applications - The specification and demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS process

This part 1 of EN 50126 - considers RAMS, understood as reliability, availability, maintainability and safety and their interaction; - considers the generic aspects of the RAMS life cycle. The guidance in this part can still be used in the application of specific standards; - defines: - a process, based on the system life cycle and tasks within it, for managing RAMS; - a systematic process, tailorable to the type and size of the system under consideration, for specifying requirements for RAMS and demonstrating that these requirements are achieved; - addresses railway specifics; - enables conflicts between RAMS elements to be controlled and managed effectively; - does not define: - RAMS targets, quantities, requirements or solutions for specific railway applications; - rules or processes pertaining to the certification of railway products against the requirements of this standard; - an approval process for the railway stakeholders. This part 1 of EN 50126 is applicable to railway application fields, namely Command, Control and Signalling, Rolling Stock and Fixed Installations, and specifically: - to the specification and demonstration of RAMS for all railway applications and at all levels of such an application, as appropriate, from complete railway systems to major systems and to individual and combined subsystems and components within these major systems, including those containing software; in particular: - to new systems; - to new systems integrated into existing systems already accepted, but only to the extent and insofar as the new system with the new functionality is being integrated. It is otherwise not applicable to any unmodified aspects of the existing system; - as far as reasonably practicable, to modifications and extensions of existing systems already accepted, but only to the extent and insofar as existing systems are being modified. It is otherwise not applicable to any unmodified aspect of the existing system; - at all relevant phases of the life cycle of an application; - for use by railway duty holders and the railway suppliers. It is not required to apply this standard to existing systems which remain unmodified, including those systems already compliant with any former version of EN 50126. The process defined by this European Standard assumes that railway duty holders and railway suppliers have business-level policies addressing Quality, Performance and Safety. The approach defined in this standard is consistent with the application of quality management requirements contained within EN ISO 9001.

Bahnanwendungen - Spezifikation und Nachweis von Zuverlässigkeit, Verfügbarkeit, Instandhaltbarkeit und Sicherheit (RAMS) - Teil 1: Generischer RAMS-Prozess

Applications ferroviaires - Spécification et démonstration de la fiabilité, de la disponibilité, de la maintenabilité et de la sécurité (FDMS) - Partie 1 : Processus FMDS générique

La présente Partie 1 de l'EN 50126 : - définit la FDMS en termes de fiabilité, de disponibilité, de maintenabilité et de sécurité et leurs interactions ; - prend en considération les aspects génériques du cycle de vie FDMS. Les lignes directrices de la présente partie s'appliquent également lors de l'application de normes spécifiques ; - définit : - un processus de management de la FDMS fondé sur le cycle de vie du système et les tâches qui en font partie ; - un processus systématique adaptable au type et à la taille du système en cours d'examen, permettant de spécifier les exigences de la FDMS et de démontrer que ces exigences sont satisfaites ; - prend en compte les spécificités du domaine ferroviaire ; - permet de contrôler et de gérer efficacement les conflits entre les composantes de la FDMS ; - ne définit pas : - les objectifs de FDMS, ni les grandeurs, les exigences ou les solutions pour des applications ferroviaires spécifiques ; - les règles ou les processus de certification des produits ferroviaires vis-à-vis des exigences de la présente norme ; - un processus d'homologation pour les parties prenantes ferroviaires. La présente Partie 1 de l'EN 50126 s'applique aux domaines d'application ferroviaire, à savoir Contrôle commande et Signalisation, Matériel Roulant et Installations Fixes, et spécifiquement : - à la spécification et à la démonstration des exigences de FDMS pour toute application ferroviaire et à tout niveau d'une telle application, selon le cas, allant des systèmes ferroviaires complets aux grands systèmes et aux sous-systèmes et équipements (individuels et combinés) de ces grands systèmes, y compris ceux qui comportent des logiciels. Elle est notamment applicable : - aux nouveaux systèmes ; - aux nouveaux systèmes intégrés dans des systèmes préexistants acceptés, mais seulement dans la mesure où, et dans la façon dont le nouveau système comprenant la nouvelle fonctionnalité y est intégré. Elle n'est sinon pas applicable aux parties inchangées du système existant ; - dans toute la mesure du possible, aux modifications et extensions des systèmes préexistants, mais seulement dans la mesure où, et dans la façon dont les systèmes existants sont modifiés. Elle n'est sinon pas applicable aux parties inchangées du système existant ; - à toutes les phases concernées du cycle de vie d'une application donnée ; - à l'utilisation des sociétés d'exploitation ferroviaire et des industries ferroviaires. Il n'est pas nécessaire d'appliquer la présente norme aux systèmes existants qui ne sont pas modifiés, y compris ceux déjà conformes à toute version antérieure de l'EN 50126. Le processus défini par la présente Norme européenne part du principe que les sociétés d'exploitation et les industries ferroviaires ont développé au niveau de l'entreprise des politiques de Qualité, Performances et Sécurité. L'approche définie dans la présente norme est en accord avec l'application des exigences de management de la qualité de l'EN ISO 9001.

Železniške naprave - Specifikacija in prikaz zanesljivosti, razpoložljivosti, vzdrževalnosti in varnosti (RAMS) - 1. del: Generični procesi RAMS - Dopolnilo A1

General Information

Status
Not Published
Publication Date
01-Jul-2024
ICS
29.280 - Electric traction equipment
45.020 - Railway engineering in general
Technical Committee
CLC/TC 9X - Electrical and electronic applications for railways
Drafting Committee
CLC/TC 9X/WG 21 - Revision of EN 50126-1 & -2
Current Stage
Directive
2016/797/EU - Directive (EU) 2016/797 of the European Parliament and of the Council of 11 May 2016 on the interoperability of the rail system within the European Union (Text with EEA relevance)
Mandate
M/483 - Mandate for programming and standardisation addressed to the European standardisation bodies under directive 2008/57/EC in the field of the interoperability of the rail system within the European Union
M/591 - Standardisation request to the European Committee for Standardisation and the European Committee for Electrotechnical Standardisation as regards railway products in support of Directive (EU) 2016/797
Ref Project
SIST EN 50126-1:2018/oprA1:2023 - Railway Applications - The Specification and Demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS Process

Relations

Amends
EN 50126-1:2017 - Railway Applications - The Specification and Demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS Process
Effective Date
26-May-2020

Buy Standard

EN 50126-1:2018/oprA1:2023EN 50126-1:2018/oprA1:2023
PreviousNext
Draft
EN 50126-1:2018/oprA1:2023
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50126-1:2018/oprA1:2023
01-april-2023
Železniške naprave - Specifikacija in prikaz zanesljivosti, razpoložljivosti,
vzdrževalnosti in varnosti (RAMS) - 1. del: Generični procesi RAMS - Dopolnilo A1
Railway Applications - The Specification and Demonstration of Reliability, Availability,
Maintainability and Safety (RAMS) - Part 1: Generic RAMS Process
Bahnanwendungen - Spezifikation und Nachweis von Zuverlässigkeit, Verfügbarkeit,
Instandhaltbarkeit und Sicherheit (RAMS) - Teil 1: Generischer RAMS-Prozess
Applications ferroviaires - Spécification et démonstration de la fiabilité, de la disponibilité,
de la maintenabilité et de la sécurité (FDMS) - Partie 1 : Processus FMDS générique
Ta slovenski standard je istoveten z: EN 50126-1:2017/prA1
ICS:
03.120.01 Kakovost na splošno Quality in general
45.020 Železniška tehnika na Railway engineering in
splošno general
SIST EN 50126-1:2018/oprA1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50126-1:2018/oprA1:2023

---------------------- Page: 2 ----------------------
SIST EN 50126-1:2018/oprA1:2023


EUROPEAN STANDARD DRAFT
EN 50126-1:2017
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
February 2023
ICS 29.280; 45.020 -
English Version
Railway Applications - The Specification and Demonstration of
Reliability, Availability, Maintainability and Safety (RAMS) - Part
1: Generic RAMS Process
Railway Applications - The Specification and Demonstration Bahnanwendungen - Spezifikation und Nachweis von
of Reliability, Availability, Maintainability and Safety (RAMS) Zuverlässigkeit, Verfügbarkeit, Instandhaltbarkeit und
- Part 1: Generic RAMS Process Sicherheit (RAMS) - Teil 1: Generischer RAMS-Prozess
This draft amendment prA1, if approved, will modify the European Standard EN 50126-1:2017; it is submitted to CENELEC members for
enquiry.
Deadline for CENELEC: 2023-04-28.

It has been drawn up by CLC/TC 9X.

If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 72022 Ref. No. EN 50126-1:2017/prA1 E

---------------------- Page: 3 ----------------------
SIST EN 50126-1:2018/oprA1:2023
EN 50126-1:2017/prA1:2023 (E)
Contents Page
European foreword . 3
1 Modification to references . 4
2 Modification to Clause 2, "Normative References" . 4
3 Modification to Clause 3, "Terms and definitions " . 4
4 Modification to Annex ZZ . 9

2

---------------------- Page: 4 ----------------------
SIST EN 50126-1:2018/oprA1:2023
EN 50126-1:2017/prA1:2023 (E)
European foreword
This document (EN 50126-1:2017/prA1:2023) has been prepared by Technical Committee CLC/TC 9X
“Electrical and electronic applications for railways”, the secretariat of which is h
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50121-5:2017/A1:2019(Amendment)
Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus
SIST EN 50121-5:2017/A1:2020

This European Standard applies to emission and immunity aspects of EMC for electrical and electronic apparatus and systems intended for use in railway fixed installations for power supply. This includes the power feed to the apparatus, the apparatus itself with its protective control circuits, trackside items such as switching stations, power autotransformers, booster transformers, substation power switchgear and power switchgear to other longitudinal and local supplies. Filters operating at railway system voltage (for example, for harmonic suppression or power factor correction) are not included in this standard since each site has special requirements. Filters would normally have separate enclosures with separate rules for access. If electromagnetic limits are required, these will appear in the specification for the equipment. If a port is intended to transmit or receive for the purpose of radio communication (intentional radiators, e.g. transponder systems), then the radiated emission requirement in this standard are not intended to be applicable to the intentional transmission from a radio-transmitter as defined by the ITU. The frequency range considered is from DC to 400 GHz. No measurements need to be performed at frequencies where no requirement is specified. Emission and immunity limits are given for items of apparatus which are situated: a) within the boundary of a substation which delivers electric power to a railway; b) beside the track for the purpose of controlling or regulating the railway power supply, including power factor correction; c) along the track for the purpose of supplying electrical power to the railway other than by means of the conductors used for contact current collection, and associated return conductors. Included are high voltage feeder systems within the boundary of the railway which supply substations at which the voltage is reduced to the railway system voltage; d) beside the track for controlling or regulating electric power supplies to ancillary railway uses. This category includes power supplies to marshalling yards, maintenance depots and stations; e) various other non-traction power supplies from railway sources which are shared with railway traction. The immunity levels given in this standard apply for: - vital equipment such as protection devices; - equipment having connections to the traction power conductors; - apparatus inside the 3 m zone; - ports of apparatus inside the 10 m zone with connection inside the 3 m zone; - ports of apparatus inside the 10 m zone with cable length > 30 m. Apparatus and systems which are in an environment which can be described as residential, commercial or light industry, even when placed within the physical boundary of the railway substation, shall comply with EN 61000-6-1:2007 for immunity and EN 61000-6-3:2007 for emission requirements. Excluded from the immunity requirements of this standard is power supply apparatus which is intrinsically immune to the tests defined in Tables 1 to 6. NOTE An example is an 18 MVA 230 kV to 25 kV power supply transformer. These specific provisions are to be used in conjunction with the general provisions in EN 50121-1. This part of the standard covers requirements for both apparatus and fixed installations. The sections for fixed installations are not relevant for CE marking.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50121-4:2016/A1:2019(Amendment)
Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signalling and telecommunications apparatus
SIST EN 50121-4:2017/A1:2019

This European Standard applies to signalling and telecommunication apparatus that is installed inside the railway environment. Signalling and telecommunication apparatus mounted in vehicles is covered by EN 50121-3-2:2016, signalling and telecommunication apparatus installed inside the substation and connected to substation equipment is covered by EN 50121-5:2016. This European Standard specifies limits for emission and immunity and provides performance criteria for signalling and telecommunications (S&T) apparatus (including power supply systems belonging to S&T) which may interfere with other apparatus inside the railway environment, or increase the total emissions for the railway environment and so risk causing Electro-Magnetic Interference (EMI) to apparatus outside the railway system. The requirements specified in this standard apply for: — vital equipment such as interlocking or command and control; — apparatus inside the 3 m zone; — ports of apparatus inside the 10 m zone with connection inside the 3 m zone; — ports of apparatus inside the 10 m zone with cable length > 30 m. Other apparatus not covered by at least one of these given cases should be in compliance with EN 61000-6-2. If a port is intended to transmit or receive for the purpose of radio communication (intentional radiators, e.g. transponder systems), then the radiated emission requirement in this standard are not intended to be applicable to the intentional transmission from a radio-transmitter as defined by the ITU. Immunity limits do not apply in the exclusion bands as defined in the corresponding EMC related standard for radio equipment. The standard does not specify basic personal safety requirements for apparatus such as protection against electric shock, unsafe operation, insulation co-ordination and related dielectric tests. The requirements were developed for and are applicable to this set of apparatus when operating under normal conditions. Fault conditions of the apparatus have not been taken into account. The frequency range considered is from DC to 400 GHz. No measurements need to be performed at frequencies where no requirement is specified. For products in the scope of EN 61000-3-2, EN 61000-3-3, EN 61000-3-11 or EN 61000-3-12 the requirements of those standards also apply. These specific provisions are to be used in conjunction with the general provisions in EN 50121-1:2016. The immunity and emission levels do not of themselves guarantee that the integration of apparatus will necessarily be satisfactory. The standard cannot cover all the possible configurations of the apparatus, but the test levels are sufficient to achieve satisfactory EMC in the majority of cases.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50126-1:2017(Main)
Railway Applications - The Specification and Demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS Process
SIST EN 50126-1:2018

This part 1 of EN 50126 - considers RAMS, understood as reliability, availability, maintainability and safety and their interaction; - considers the generic aspects of the RAMS life cycle. The guidance in this part can still be used in the application of specific standards; - defines: - a process, based on the system life cycle and tasks within it, for managing RAMS; - a systematic process, tailorable to the type and size of the system under consideration, for specifying requirements for RAMS and demonstrating that these requirements are achieved; - addresses railway specifics; - enables conflicts between RAMS elements to be controlled and managed effectively; - does not define: - RAMS targets, quantities, requirements or solutions for specific railway applications; - rules or processes pertaining to the certification of railway products against the requirements of this standard; - an approval process for the railway stakeholders. This part 1 of EN 50126 is applicable to railway application fields, namely Command, Control and Signalling, Rolling Stock and Fixed Installations, and specifically: - to the specification and demonstration of RAMS for all railway applications and at all levels of such an application, as appropriate, from complete railway systems to major systems and to individual and combined subsystems and components within these major systems, including those containing software; in particular: - to new systems; - to new systems integrated into existing systems already accepted, but only to the extent and insofar as the new system with the new functionality is being integrated. It is otherwise not applicable to any unmodified aspects of the existing system; - as far as reasonably practicable, to modifications and extensions of existing systems already accepted, but only to the extent and insofar as existing systems are being modified. It is otherwise not applicable to any unmodified aspect of the existing system; - at all relevant phases of the life cycle of an application; - for use by railway duty holders and the railway suppliers. It is not required to apply this standard to existing systems which remain unmodified, including those systems already compliant with any former version of EN 50126. The process defined by this European Standard assumes that railway duty holders and railway suppliers have business-level policies addressing Quality, Performance and Safety. The approach defined in this standard is consistent with the application of quality management requirements contained within EN ISO 9001.

  • Standard
    103 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    114 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50121-5:2017(Main)
Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus
SIST EN 50121-5:2017

This European Standard applies to emission and immunity aspects of EMC for electrical and electronic apparatus and systems intended for use in railway fixed installations for power supply. This includes the power feed to the apparatus, the apparatus itself with its protective control circuits, trackside items such as switching stations, power autotransformers, booster transformers, substation power switchgear and power switchgear to other longitudinal and local supplies. Filters operating at railway system voltage (for example, for harmonic suppression or power factor correction) are not included in this standard since each site has special requirements. Filters would normally have separate enclosures with separate rules for access. If electromagnetic limits are required, these will appear in the specification for the equipment. If a port is intended to transmit or receive for the purpose of radio communication (intentional radiators, e.g. transponder systems), then the radiated emission requirement in this standard are not intended to be applicable to the intentional transmission from a radio-transmitter as defined by the ITU. The frequency range considered is from DC to 400 GHz. No measurements need to be performed at frequencies where no requirement is specified. Emission and immunity limits are given for items of apparatus which are situated: a) within the boundary of a substation which delivers electric power to a railway; b) beside the track for the purpose of controlling or regulating the railway power supply, including power factor correction; c) along the track for the purpose of supplying electrical power to the railway other than by means of the conductors used for contact current collection, and associated return conductors. Included are high voltage feeder systems within the boundary of the railway which supply substations at which the voltage is reduced to the railway system voltage; d) beside the track for controlling or regulating electric power supplies to ancillary railway uses. This category includes power supplies to marshalling yards, maintenance depots and stations; e) various other non-traction power supplies from railway sources which are shared with railway traction. The immunity levels given in this standard apply for: - vital equipment such as protection devices; - equipment having connections to the traction power conductors; - apparatus inside the 3 m zone; - ports of apparatus inside the 10 m zone with connection inside the 3 m zone; - ports of apparatus inside the 10 m zone with cable length > 30 m. Apparatus and systems which are in an environment which can be described as residential, commercial or light industry, even when placed within the physical boundary of the railway substation, shall comply with EN 61000 6 1:2007 for immunity and EN 61000 6 3:2007 for emission requirements. Excluded from the immunity requirements of this standard is power supply apparatus which is intrinsically immune to the tests defined in Tables 1 to 6. NOTE An example is an 18 MVA 230 kV to 25 kV power supply transformer. These specific provisions are to be used in conjunction with the general provisions in EN 50121 1. This part of the standard covers requirements for both apparatus and fixed installations. The sections for fixed installations are not relevant for CE marking.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50121-1:2017(Main)
Railway applications - Electromagnetic compatibility - Part 1: General
SIST EN 50121-1:2017

This European standard outlines the structure and the content of the whole set. It specifies the performance criteria applicable to the whole standards series. Clause 5 provides information about the EMC management. This part alone is not sufficient to give presumption of conformity to the essential requirements of the EMC-Directive and is intended to be used in conjunction with other parts of this standard. Annex A describes the characteristics of the railway system which affect electromagnetic compatibility (EMC) behaviour. Phenomena excluded from the set are Nuclear EM pulse, abnormal operating conditions (e.g. fault conditions) and the induction effects of direct lightning strike. Emission limits at the railway system boundary do not apply to intentional transmitters within the railway system boundaries. Safety considerations are not covered by this set of standards. The biological effects of non-ionizing radiation as well as apparatus for medical assistance, such as pacemakers, are not considered here.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50121-2:2017(Main)
Railway applications - Electromagnetic compatibility - Part 2: Emission of the whole railway system to the outside world
SIST EN 50121-2:2017

This European Standard is intended to define the electromagnetic environment of the whole railway system including urban mass transit and light rail system. It describes the measurement method to verify the emissions, and gives the cartography values of the fields most frequently encountered. This European Standard specifies the emission limits of the whole railway system to the outside world. The emission parameters refer to the particular measuring points defined in Clause 5. These emissions should be assumed to exist at all points in the vertical planes which are 10 m from the centre lines of the outer electrified railway tracks, or 10 m from the fence of the substations. Also, the zones above and below the railway system may be affected by electromagnetic emissions and particular cases need to be considered individually. These specific provisions need to be used in conjunction with the general provisions in EN 50121-1. For existing railway lines, it is assumed that compliance with the emission requirements of EN 50121-3-1, EN 50121-3-2, EN 50121-4 and EN 50121 5 will ensure the compliance with the emission values given in this part. For newly build railway systems it is best practice to provide compliance to the emission limits given in this part of the standard (as defined in the EMC plan according to EN 50121-1).

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50121-4:2016(Main)
Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signalling and telecommunications apparatus
SIST EN 50121-4:2017

This European Standard applies to signalling and telecommunication apparatus that is installed inside the railway environment. Signalling and telecommunication apparatus mounted in vehicles is covered by FprEN 50121 3 2:2016, signalling and telecommunication apparatus installed inside the substation and connected to substation equipment is covered by FprEN 50121 5:2016. This European Standard specifies limits for emission and immunity and provides performance criteria for signalling and telecommunications (S&T) apparatus (including power supply systems belonging to S&T) which may interfere with other apparatus inside the railway environment, or increase the total emissions for the railway environment and so risk causing Electro-Magnetic Interference (EMI) to apparatus outside the railway system. The requirements specified given in this standard apply for: — vital equipment such as interlocking or command and control; — apparatus inside the 3 m zone; — ports of apparatus inside the 10 m zone with connection inside the 3 m zone; — ports of apparatus inside the 10 m zone with cable length > 30 m. Other apparatus not covered by at least one of these given cases should be in compliance with EN 61000 6 2. If a port is intended to transmit or receive for the purpose of radio communication (intentional radiators, e.g. transponder systems), then the radiated emission requirement in this standard are not intended to be applicable to the intentional transmission from a radio-transmitter as defined by the ITU. Immunity limits do not apply in the exclusion bands as defined in the corresponding EMC related standard for radio equipment. The standard does not specify basic personal safety requirements for apparatus such as protection against electric shock, unsafe operation, insulation co-ordination and related dielectric tests. The requirements were developed for and are applicable to this set of apparatus when operating under normal conditions. Fault conditions of the apparatus have not been taken into account. The frequency range considered is from DC to 400 GHz. No measurements need to be performed at frequencies where no requirement is specified. For products in the scope of EN 61000 3 2, EN 61000 3 3, EN 61000 3 11 or EN 61000 3 12 the requirements of those standards also apply. These specific provisions are to be used in conjunction with the general provisions in FprEN 50121 1:2016. The immunity and emission levels do not of themselves guarantee that the integration of apparatus will necessarily be satisfactory. The standard cannot cover all the possible configurations of the apparatus, but the test levels are sufficient to achieve satisfactory EMC in the majority of cases.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50123-4:2003/A1:2013(Amendment)
Railway applications - Fixed installations - D.C. switchgear - Part 4: Outdoor d.c. disconnectors, switch-disconnectors and earthing switches
SIST EN 50123-4:2003/A1:2014

2013-07-25: Publication allocated to cpalagi@cencenelec.eu * In hands of WG 18
2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50152-1:2012(Main)
Railway applications - Fixed installations - Particular requirements for alternating current switchgear - Part 1: Circuit-breakers with nominal voltage above 1 kV
SIST EN 50152-1:2013

This EN 50152-1 is applicable to single-pole and two-pole alternating current (a.c.) circuit-breakers which are: - for indoor or outdoor fixed installations in tractions systems, and - operated with an a.c. line voltage and frequency as specified in EN 50163. NOTE 1 EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz. NOTE 2 As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages are sometimes higher e.g. in autotransformer systems. This European Standard is also applicable to the operating devices of circuit-breakers and to their auxiliary equipment. This European Standard does not address circuit-breakers with dependent manual operating mechanism. NOTE 3 It is impossible to specify a rated short-circuit making current for these circuit-breakers and it is likely that such dependent manual operation is not meeting safety considerations.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50123-3:2003(Main)
Railway applications - Fixed installations - D.C. switchgear - Part 3: Indoor d.c. disconnectors, switch-disconnectors and earthing switches
SIST EN 50123-3:2003

This part of EN 50123 specifies requirements for d.c. disconnectors, switch-disconnectors and earthing switches for use in indoor fixed installations of traction systems. NOTE 1 Switchgear assemblies, electromagnetic compatibility (EMC) and dependability are not covered in this part of EN 50123, but rather by other parts of this standard or other documents as indicated in EN 50123 1. NOTE 2 In this standard the word "unit" means "disconnector and/or switch-disconnector and/or earthing switch" as defined in 3.1.4, 3.1.5 and 3.1.6 of EN 50123 1. NOTE 3 Disconnectors, switch-disconnectors and earthing switches may have electrically latched mechanisms and, in such cases, may be indicated with the current term of "power contactors".

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day