EN 61988-1:2003
(Main)Plasma display panels - Part 1: Terminology and letter symbols
Plasma display panels - Part 1: Terminology and letter symbols
Gives the preferred terms, their definitions and symbols for colour AC plasma display panels (AC PDP); with the object of using the same terminology when publications are prepared in different countries. Guidance on the technology is provided in the annexes.
Plasmabildschirme - Teil 1: Terminologie und Buchstabensymbole
Panneaux d'affichage à plasma - Partie 1: Terminologie et symboles littéraux
Gives the preferred terms, their definitions and symbols for colour AC plasma display panels (AC PDP); with the object of using the same terminology when publications are prepared in different countries. Guidance on the technology is provided in the annexes.
Prikazalniki s plazmo – 1. del: Izrazje in črkovni simboli (IEC 61988-1:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61988-1:2005
STANDARD
december 2005
Prikazalniki s plazmo – 1. del: Izrazje in črkovni simboli (IEC 61988-1:2003)
Plasma display panels – Part 1: Terminology and letter symbols (IEC 61988-1:2003)
ICS 31.120 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 61988-1
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2003
ICS 31.260
English version
Plasma display panels
Part 1: Terminology and letter symbols
(IEC 61988-1:2003)
Panneaux d'affichage à plasma Plasmabildschirme
Partie 1: Terminologie et Teil 1: Terminologie und
symboles littéraux Buchstabensymbole
(CEI 61988-1:2003) (IEC 61988-1:2003)
This European Standard was approved by CENELEC on 2003-05-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61988-1:2003 E
Foreword
The text of document 47C/289/FDIS, future edition 1 of IEC 61988-1, prepared by SC 47C, Flat panel
display devices, of IEC TC 47, Semiconductor devices, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 61988-1 on 2003-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-05-01
Annexes designated "normative" are part of the body of the standard.
Annexes designated "informative" are given for information only.
In this standard, annex ZA is normative and annexes A, B, C, D and E are informative.
Annex ZA has been added by CENELEC.
____
Endorsement notice
The text of the International Standard IEC 61988-1:2003 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61988-1:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 61988-2-1 - Plasma display panels EN 61988-2-1 2002
Part 2-1: Measuring methods – Optical
1) 2)
IEC 61988-2-2 - Part 2-2: Measuring methods - EN 61988-2-2 2003
Optoelectrical
CIE 15.2 1986 Colorimetry - -
1)
Undated reference.
2)
Valid edition at date of issue.
NORME CEI
INTERNATIONALE IEC
61988-1
INTERNATIONAL
Première édition
STANDARD
First edition
2003-05
Panneaux d'affichage à plasma –
Partie 1:
Terminologie et symboles littéraux
Plasma display panels –
Part 1:
Terminology and letter symbols
© IEC 2003 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
PRICE CODE X
Commission Electrotechnique Internationale
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue
61988-1 © IEC:2003 – 3 –
CONTENTS
FOREWORD . 5
1 Scope . 9
2 Normative references. 9
3 Terms and definitions . 9
4 Symbols.57
4.1 Symbol list by term name.57
4.2 Symbol list by symbol .59
Annex A (informative) Description of the technology.63
Annex B (informative) Relationship between voltage terms and discharge
characteristics.87
Annex C (informative) Gaps .89
Annex D (informative) Manufacturing .91
Annex E (informative) Interconnect pad.97
Figure A.1 – Principal structures and discharge characteristics of a DC PDP cell and
an AC PDP cell .63
Figure A.2 – Discharge characteristics of a cell (single cell static characteristics) .67
Figure A.3 – Static characteristics of cells in a panel or a group of cells.69
Figure A.4 – Write waveform components .71
Figure A.5 – Operation of a two-electrode type AC PDP.73
Figure A.6 – Relation between margins and applied voltages .75
Figure A.7 – Structure of a three-electrode type, surface discharge colour AC PDP .77
Figure A.8 – Address-, Display-period separation method .81
Figure A.9 – A driving waveform for ADS method applied to a three-electrode .83
Figure A.10 – Address while display method .85
Figure C.1 – Gaps (sustain gap, plate gap and interpixel gap) in a three-electrode
type AC PDP.89
Figure D.1 – PDP manufacturing flow chart .93
Figure E.1 – Interconnect pad group .97
Figure E.2 – Dimensions of interconnect pads.97
Table B.1 – Relation between static, dynamic and operating discharge characteristics
in a cell, a panel or a group of cells.87
61988-1 © IEC:2003 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
––––––––––––
PLASMA DISPLAY PANELS –
Part 1: Terminology and letter symbols
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to
technical committees; any IEC National Committee interested in the subject dealt with may participate in this
preparatory work. International, governmental and non-governmental organizations liaising with the IEC also
participate in this preparation. IEC collaborates closely with the International Organization for Standardization
(ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61988-1 has been prepared by subcommittee 47C: Flat panel
display devices , of IEC technical committee 47: Semiconductor devices.
This bilingual version (2003-08) replaces the English version.
The text of this standard is based on the following documents:
FDIS Report on voting
47C/289/FDIS 47C/296/RVD
Full information on the voting for the approval on this standard can be found in the report on
voting indicated in the above table.
———————
Subcommittee 47C has been converted into committee 110: Flat panel display devices.
61988-1 © IEC:2003 – 7 –
The French version of this standard has not been voted upon.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 61988 will consist of the following parts, under the general title Plasma display panels:
Part 1: Terminology and letter symbols;
Part 2-1: Measuring methods – Optical;
Part 2-2: Measuring methods – Optoelectrical;
Part 3: Guidelines of mechanical interface;
Part 4: Environmental, endurance and mechanical test methods.
The committee has decided that the contents of this publication will remain unchanged until
2008. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
61988-1 © IEC:2003 – 9 –
PLASMA DISPLAY PANELS –
Part 1: Terminology and letter symbols
1 Scope
This part of IEC 61988 gives the preferred terms, their definitions and symbols for colour
AC plasma display panels (AC PDP); with the object of using the same terminology when
publications are prepared in different countries. Guidance on the technology is provided
in the annexes.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 61988-2-1, Plasma display panels – Part 2-1: Measuring methods – Optical
IEC 61988-2-2, Plasma display panels – Part 2-2: Measuring methods – Optoelectrical
nd
CIE 15.2:1986, Colorimetry, 2 Edition
3 Terms and defin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.