EN 61988-3-2:2009
(Main)Plasma display panels - Part 3-2: Interface - Electrical interface
Plasma display panels - Part 3-2: Interface - Electrical interface
IEC 61988-3-2:2009 defines the electrical interface of digital video data signals, synchronization signals and functional signals between the image processing board of the PDP set and the control board of the PDP module, and defines the description of the pin assignment of the connectors.
Plasmabildschirme - Teil 3-2: Schnittstelle - Elektrische Schnittstelle
Panneaux d'affichage à plasma - Partie 3-2: Interface - Interface électrique
La CEI 61988-3-2:2009 définit l'interface électrique des signaux de données vidéo numériques, des signaux de synchronisation et des signaux fonctionnels entre la carte de traitement d'image de l'ensemble PDP (plasma display panel) et la carte de commande du module PDP, et elle définit l'affectation des broches des connecteurs.
Plošče s plazemskim prikazovalnikom - 3-2. del: Električni vmesnik (IEC 61988-3-2:2009)
Ta del IEC 61988 določa električni vmesnik za digitalne podatkovne video signale, sinhronizacijske signale in funkcionalne signale med ploščo za obdelavo slik seta PDP in nadzorno ploščo modula PDP ter določa opis določanja polov konektorjev.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2010
3ORãþHVSOD]HPVNLPSULND]RYDOQLNRPGHO (OHNWULþQLYPHVQLN ,(&
Plasma display panels - Part 3-2: Electrical interface (IEC 61988-3-2:2009)
Plasmabildschirme - Teil 3-2: Schnittstelle - Elektrische Schnittstelle (IEC 61988-3-
2:2009)
Panneaux d'affichage à plasma - Partie 3-2: Interface électrique (CEI 61988-3-2:2009)
Ta slovenski standard je istoveten z: EN 61988-3-2:2009
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 61988-3-2
NORME EUROPÉENNE
November 2009
EUROPÄISCHE NORM
ICS 31.260
English version
Plasma display panels -
Part 3-2: Interface -
Electrical interface
(IEC 61988-3-2:2009)
Panneaux d'affichage à plasma - Plasmabildschirme -
Partie 3-2: Interface - Teil 3-2: Schnittstelle -
Interface électrique Elektrische Schnittstelle
(CEI 61988-3-2:2009) (IEC 61988-3-2:2009)
This European Standard was approved by CENELEC on 2009-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61988-3-2:2009 E
Foreword
The text of document 110/181/FDIS, future edition 1 of IEC 61988-3-2, prepared by IEC TC 110, Flat
panel display devices, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC
as EN 61988-3-2 on 2009-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61988-3-2:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-1 NOTE Harmonized as EN 60068-1:1994 (not modified).
IEC 60107-1 NOTE Harmonized as EN 60107-1:1997 (not modified).
__________
- 3 - EN 61988-3-2:2009
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
1) 2)
IEC 61988-1 - Plasma display panels - EN 61988-1 2003
Part 1: Terminology and letter symbols
1) 2)
IEC 61988-2-1 - Plasma display panels - EN 61988-2-1 2002
Part 2-1: Measuring methods - Optical
1) 2)
IEC 61988-2-2 - Plasma display panels - EN 61988-2-2 2003
Part 2-2: Measuring methods - Optoelectrical
1)
ANSI TIA/ - Electrical Characteristics of Low Voltage - -
EIA-644-A Differential Signaling (LVDS) Interface Circuits
JEIDA-59 1999 Digital Interface Standards for Monitor - -
1)
Undated reference.
2)
Valid edition at date of issue.
IEC 61988-3-2 ®
Edition 1.0 2009-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Plasma display panels –
Part 3-2: Interface – Electrical interface
Panneaux d’affichage à plasma –
Partie 3-2: Interface – Interface électrique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
T
CODE PRIX
ICS 31.260 ISBN 2-8318-1054-3
– 2 – 61988-3-2 © IEC:2009
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references .5
3 Terms, definitions and abbreviations .5
3.1 Terms and definitions .5
3.2 Abbreviations .5
4 Electrical interface requirements .6
5 Electrical interface of digital signal .6
5.1 Basic configuration.6
5.2 Interface input signal definition.7
5.3 Pin assignment.9
5.4 Input signal timing .10
5.5 Power requirement .10
Annex A (informative) LVDS, TTL and TMDS.11
Bibliography.24
Figure 1 – Block diagram of an example interface of data signal .7
Figure A.1 – Interface configuration .11
Figure A.2 – Timing chart for resolution 1024 x 768 .14
Figure A.3 – Logic power and LVDS signals sequencing diagram .15
Figure A.4 – Data enable timing parameters .16
Figure A.5 – Interface configuration .17
Figure A.6 – Interface configuration .20
Table 1 – Example of interface signal function .8
Table 2 – Example of connector pin assignments.9
Table A.1 – Signal definition and function .12
Table A.2 – Connector pin assignment.13
Table A.3 – Input signal timing specification for resolution 1024x768 .15
Table A.4 – Input signal specifications .18
Table A.5 – Connector pin assignments .19
Table A.6 – Input signal specifications .21
Table A.7 – Example of pin assignment of connector .21
Table A.8 –Limiting values (Absolute maximum rating system) .22
Table A.9 – Electrical characteristics .23
61988-3-2 © IEC:2009 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
PLASMA DISPLAY PANELS –
Part 3-2: Interface –
Electrical interface
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61988-3-2 has been prepared by IEC technical committee 110:
Flat panel display devices.
The text of this standard is based on the following documents:
FDIS Report on voting
110/181/FDIS 110/190/RVD
Full information on the voting for the approval on this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 61988 series, under the general title Plasma display panels,
can be found on the IEC website.
– 4 – 61988-3-2 © IEC:2009
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
61988-3-2 © IEC:2009 – 5 –
PLASMA DISPLAY PANELS –
Part 3-2: Interface –
Electrical interface
1 Scope
This part of IEC 61988 defines the electrical interface of digital video data signals,
synchronization signals and functional signals between the image processing board of the
PDP set and the control board of the PDP module, and defines the description of the pin
assignment of the connectors.
2 Normative references
The following referenced docu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.