EN 61823:2003

Electrical installations for lighting and beaconing of aerodromes - AGL series transformers

This standard specifies the characteristics of aeronautical ground lighting series trans-formers (AGLST) used in aeronautical ground lighting for 6,6 A series circuits, at a service voltage of up to 5 kV, supplied by constant current regulators up to 30 kVA in rating. AGL series transformers provide power to airport lighting luminaires or other loads (resistive) from their secondary circuits. The AGL series transformers provide continuity of the series circuit in the event of a loss of the load on the transformer, and electrical isolation between the primary circuit supplied by a constant current regulator, and the secondary circuit connected to the load under conditions defined in this standard.

Elektrische Anlagen für Beleuchtung und Befeuerung von Flugplätzen - Serienstromtransformatoren

Installations électriques pour le balisage et l'éclairage des aérodromes - Transformateurs séries AGL

L'IEC 61823:2002 spécifie les caractéristiques des transformateurs série utilisés pour le balisage aéronautique au sol (AGLST) pour des circuits série de 6,6 A, dont la tension de service atteint 5 kV, alimentés par des régulateurs de courant constant jusqu'à 30 kVA. Les transformateurs série AGL assurent l'alimentation des feux aéronautiques de balisage ou d'autres charges (résistives) à partir de leurs circuits secondaires. Les transformateurs série AGL assurent la continuité du circuit série en cas de perte de charge sur le transformateur, et l'isolation électrique entre le circuit primaire alimenté par un régulateur de courant constant et le circuit secondaire connecté à la charge dans des conditions définies dans la présente Norme. La présente version bilingue (2016-11) correspond à la version anglaise monolingue publiée en 2002-12.

Electrical installations for lighting and beaconing of aerodromes - AGL series transformers

General Information

• Status: Published
• Publication Date: 12-Jun-2003
• ICS: 29.140.50 - Lighting installation systems
• ICS: 93.120 - Construction of airports
• Technical Committee: CLC/SR 97 - Electrical installations for lighting and beaconing of aerodromes
• Drafting Committee: IEC/TC 97 - IEC_TC_97
• Parallel Committee: IEC/TC 97 - IEC_TC_97
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 13-Jun-2003
• Completion Date: 13-Jun-2003
• Ref Project: SIST EN 61823:2003 - Electrical installations for lighting and beaconing of aerodromes - AGL series transformers

Relations

• Replaces: ENV 50232:1997 - Aeronautical ground lighting electrical installation - Isolating transformer: Equipment specifications and tests
• Effective Date: 29-Jan-2023

Standards Content (Sample)

STANDARDElectrical installations for lighting and beaconing of aerodromes - AGL series transformers©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 61823:2003(en)ICS29.140.50; 93.120

EUROPEAN STANDARD
EN 61823 NORME EUROPÉENNE EUROPÄISCHE NORM
June 2003 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61823:2003 E
ICS 29.140.50; 93.120
English version
Electrical installations for lighting and beaconing of aerodromes -
AGL series transformers (IEC 61823:2002, modified)
Installations électriques pour le balisage et l'éclairage des aérodromes - Transformateurs séries AGL (CEI 61823:2002, modifiée)
Elektrische Anlagen für Beleuchtung
und Befeuerung von Flugplätzen - Serienstromtransformatoren (IEC 61823:2002, modifiziert)
This European Standard was approved by CENELEC on 2003-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

at national level by publication of an identical
national standard or by endorsement
(dop) 2004-01-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow) 2006-02-01 Annexes designated "normative" are part of the body of the standard.
In this standard, annexes A and ZA are normative. Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 61823:2002 was approved by CENELEC as a European Standard with agreed common modifications as given below. COMMON MODIFICATIONS 3.1.2 Add at the end of the definition ", unless otherwise stated" 4.4 Add at the end of the first paragraph "(See Annex A.)". Bibliography Add the following note for IEC 61821: NOTE
Harmonized as EN 61821:2003 (not modified). __________

- 3 - EN 61823:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60085 - 1) Thermal evaluation and classification of electrical insulation
HD 566 S1 1990 2) IEC 61822 (mod.) - 1) Electrical installations for lighting and beaconing of aerodromes - Constant current regulators
EN 61822 2003 2) ISO 48 - 1) Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) - -
1) Undated reference.
2) Valid edition at date of issue.

INTERNATIONALSTANDARDIEC61823First edition2002-12Electrical installations for lightingand beaconing of aerodromes –AGL series transformersInstallations électriques pour le balisageet l'éclairage des aérodromes –Transformateurs séries AGL IEC 2002

Copyright - all rights reservedNo part of this publication may be reproduced or utilized in any form or by any means, electronic ormechanical, including photocopying and microfilm, without permission in writing from the publisher.International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: [phone]
Telefax: [phone]
E-mail: [e-mail]
Web: www.iec.chSFor price, see current cataloguePRICE CODECommission Electrotechnique InternationaleInternational Electrotechnical Commission

– 2 –61823  IEC:2002(E)CONTENTSFOREWORD.41Scope.52Normative references.53Definitions and abbreviated terms.53.1Definitions.53.2Abbreviated terms.64General requirements.74.1Classification.74.2Rated current.74.3Earthing.74.4AGL construction.74.5Encapsulation.84.6Earthing.84.7Service conditions.84.8Electrical characteristics.84.9Temperature rise.95Type and routine tests.105.1Type tests.105.2Routine tests.116Test requirements.116.1Introduction to electrical testing.116.2Tests under load.126.3Short circuit current.136.4Open circuit voltage.136.5AC leakage current test.136.6DC leakage current cycling test.156.7Shock tests.166.8Temperature rise.176.9Gas tightness test.186.10Physical size demonstration.187Routine tests.187.1Ratio test.187.2Earth continuity test.187.3Leakage current test.188Marking.19Annex A (normative)
Connector descriptions and interface dimensions.20Bibliography.22Figure 1 – Tests under load.12Figure 2 – Primary a.c. leakage current test.14Figure 3 – Secondary a.c. leakage current test.14Figure 4 – Primary d.c. leakage current.16Figure 5 – Secondary d.c. leakage current.16Figure 6 – Lead rigidity test.17

61823  IEC:2002(E)– 3 –Figure A.1 – Style 2 primary plug.20Figure A.2 – Style 9 primary receptacle.20Figure A.3 – Style 8 secondary receptacle.21Figure A.4 – Style 7 secondary receptacle.21Table 1 – Transformer characteristics.9Table 2 – Encapsulation method type tests.10Table 3 – Electrical characteristic type tests.11Table 4 – Routine tests.11Table 5 – DC leakage current test limits.15Table A.1 – Interface dimensions for Figures A.1 and A.2.20Table A.2 – Interface dimensions for Figures A.3 and A.4.21

– 4 –61823  IEC:2002(E)INTERNATIONAL ELECTROTECHNICAL COMMISSION___________ELECTRICAL INSTALLATIONS FOR LIGHTINGAND BEACONING OF AERODROMES –AGL SERIES TRANSFORMERSFOREWORD1)The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprisingall national electrotechnical committees (IEC National Committees). The object of the IEC is to promoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields. Tothis end and in addition to other activities, the IEC publishes International Standards. Their preparation isentrusted to technical committees; any IEC National Committee interested in the subject dealt with mayparticipate in this preparatory work. International, governmental and non-governmental organizations liaisingwith the IEC also participate in this preparation. The IEC collaborates closely with the InternationalOrganization for Standardization (ISO) in accordance with conditions determined by agreement between thetwo organizations.2)The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, aninternational consensus of opinion on the relevant subjects since each technical committee has representationfrom all interested National Committees.3)The documents produced have the form of recommendations for international use and are published in the formof standards, technical specifications, technical reports or guides and they are accepted by the NationalCommittees in that sense.4)In order to promote international unification, IEC National Committees undertake to apply IEC InternationalStandards transparently to the maximum extent possible in their national and regional standards. Anydivergence between the IEC Standard and the corresponding national or regional standard shall be clearlyindicated in the latter.5)The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for anyequipment declared to be in conformity with one of its standards.6)Attention is drawn to the possibility that some of the elements of this International Standard may be the subjectof patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.International Standard IEC 61823 has been prepared by IEC technical committee 97:Electrical installations for lighting and beaconing of aerodromes.The text of this standard is based on the following documents:FDISReport on voting97/94/FDIS97/95/RVDFull information on the voting for the approval of this standard can be found in the report onvoting indicated in the above table.This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.The committee has decided that the contents of this publication will remain unchangeduntil 2006. At this date, the publication will be•reconfi
...