Nanomanufacturing - Key control characteristics - Part 4-6: Nano-enabled electrical energy storage devices - Determination of carbon content for nano electrode materials, infrared absorption method

IEC TS 62607-4-6:2018(E) provides a method for determination of carbon content of nano electrode materials by infrared absorption spectroscopy method. The method is applicable to carbon contents of mass fraction between 0,001 % and 100 %.
This method will enable customers to:
a) decide whether or not a nano electrode material is usable, and
b) select a nano electrode material with suitable carbon content for its application.
This document includes:
- recommendations for sample preparation,
- outlines of the experimental procedures used to measure electrode nanomaterial properties,
- methods of interpretation of results and discussion of data analysis, and
- case studies.

General Information

Status
Published
Publication Date
07-Feb-2018
Current Stage
PPUB - Publication issued
Start Date
13-Mar-2018
Completion Date
08-Feb-2018
Ref Project

Buy Standard

Technical specification
IEC TS 62607-4-6:2018 - Nanomanufacturing - Key control characteristics - Part 4-6: Nano-enabled electrical energy storage devices - Determination of carbon content for nano electrode materials, infrared absorption method
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TS 62607-4-6 ®
Edition 1.0 2018-02
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –
Part 4-6: Nano-enabled electrical energy storage – Determination of carbon
content for nano-enabled electrode materials, infrared absorption method
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62607-4-6 ®
Edition 1.0 2018-02
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –

Part 4-6: Nano-enabled electrical energy storage – Determination of carbon

content for nano-enabled electrode materials, infrared absorption method

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 07.030; 07.120 ISBN 978-2-8322-5363-2

– 2 – IEC TS 62607-4-6:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Terms and definitions . 6
electrode nanomaterial . 7
3.2 Abbreviated terms . 7
4 Reagents and materials . 7
4.1 Analysis gas . 7
4.2 Carrier gas . 7
4.3 Fluxes . 7
4.4 Certified reference materials . 7
5 Apparatus . 7
5.1 Analytical balance . 7
5.2 Powder compressor . 8
5.3 High-frequency infrared ray carbon/sulfur analyzer . 8
5.4 Muffle furnace . 8
5.5 Crucibles . 8
6 Test methods . 8
6.1 General . 8
6.2 Sample preparation . 8
6.2.1 Drying . 8
6.2.2 Tableting . 9
6.3 Start up . 9
6.4 Blank verification and determination. 9
6.5 Checking and calibration . 9
6.6 Analysis . 9
6.7 Reporting the results . 9
7 Data verification . 10
8 Test report . 10
Annex A (informative) Case study . 11
A.1 The gas path diagram and the light path diagram . 11
A.2 Procedures of sample preparation and carbon content determination . 12
A.3 Data analysis for carbon content determination . 13
Bibliography . 15

Figure A.1 – The gas and light (dashed box) path diagram . 11
Figure A.2 – A-B-C Procedures of sample preparation and carbon content
determination . 12

Table 1 – Recommended working conditions of high frequency infrared carbon and
sulfur analyzer . 8
Table A.1 – Measurement method consistency and measurement results of different
samples in the same laboratory . 13
Table A.2 – Inter-laboratory consistency and measurement results of the same sample . 14

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
NANOMANUFACTURING – KEY CONTROL CHARACTERISTICS –

Part 4-6: Nano-enabled electrical energy storage – Determination
of carbon content for nano-enabled electrode materials, infrared
absorption method
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. In
exceptional circumstances, a technical committee may propose the publication of a technical
specification when
• the required support cannot be obtained for the publication of an International Standard,
despite repeated efforts, or
• the subject is still under technical development or where, for any other reason, there is the
future but no immediate possibility of an agreement on an International Standard.
Technical specifications are subject to review within three years of publication to decide
whether they can be transformed into International Standards.
International Standard IEC 62607-4-6 has been prepared by IEC technical committee 113:
Nanotechnology for electrotechnical products and systems.

– 4 – IEC TS 62607-4-6:2018 © IEC 2018
The text of this technical specification is based on the following documents:
Enquiry draft Report on voting
113/379/DTS 113/402/RVDTS
Full information on the voting for the approval of this technical specification can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62607 series, published under the general title
Nanomanufacturing – key control characteristics, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.