IEC TS 63236-2:2021
(Main)Direct current (DC) appliance couplers for information and communication technology (ICT) equipment installed in data centres and telecom central offices - Part 2: 5,2 kW system
Direct current (DC) appliance couplers for information and communication technology (ICT) equipment installed in data centres and telecom central offices - Part 2: 5,2 kW system
IEC TS 63236-2:2021(E) applies to DC appliance couplers for class I equipment with two active contacts plus an earthing contact, a rated power of 5,2 kW and a rated voltage range from 294 V to 400 V DC. They are intended to power DC information and communication technology equipment only, as specified in IEC 62368-1.
This Part 2 is to be used in conjunction with IEC TS 63236-1:2021.
General Information
Standards Content (Sample)
IEC TS 63236-2 ®
Edition 1.0 2021-06
TECHNICAL
SPECIFICATION
Direct current (DC) appliance couplers for information and communication
technology (ICT) equipment installed in data centres and telecom central
offices –
Part 2: 5,2 kW system
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 63236-2 ®
Edition 1.0 2021-06
TECHNICAL
SPECIFICATION
Direct current (DC) appliance couplers for information and communication
technology (ICT) equipment installed in data centres and telecom central
offices –
Part 2: 5,2 kW system
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.120.01, 29.120.30 ISBN 978-2-8322-9928-9
– 2 – IEC TS 63236-2:2021 © IEC 2021
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 7
4 General requirements . 7
5 General notes on tests . 7
6 Standard ratings . 7
7 Classification of appliance coupler . 7
8 Marking . 8
9 Dimensions and compatibility . 8
10 Protection against electric shock . 8
11 Provision for earthing . 8
12 Terminals and terminations . 8
13 Construction . 8
14 Insulation resistance and electric strength . 9
15 Forces necessary to insert and to withdraw the connector . 9
15.1 General . 9
16 Operation of contact . 9
17 Resistance to heating of appliance coupler . 9
18 Breaking capacity . 10
19 Normal operation . 10
20 Temperature rise . 10
21 Cords and their connection . 11
21.1 Cords for non-rewirable connectors . 11
21.2 Cable anchorage . 11
22 Mechanical strength . 12
23 Resistance to heat and ageing. 12
24 Screws, current-carrying parts and connections . 12
24.1 General . 12
25 Creepage distances, clearances and distances through sealing compound . 12
26 Resistance of insulating material to heat, fire and tracking . 12
27 Resistance to rusting . 13
28 Electromagnetic compatibility (EMC) requirements . 13
101 0 (zero) current operated appliance inlet systems . 13
Annex A (xxx) Safety-related routine tests for factory-wired accessories (protection
against electric shock and correct polarity) . 14
Annex B (xxx) Test schedule . 15
Annex C (xxx) Alternative gripping tests . 16
Annex D (xxx) Standard sheets and gauges . 17
D.1 Standard sheets . 17
D.2 Gauges . 22
D.2.1 Distance to the point of first contact . 22
D.2.2 "GO" gauges for appliance inlets according to standard sheet 1
(Figure D.1) . 23
D.2.3 "GO" gauge for connectors according to standard sheet 2 (Figure D.2). 25
D.2.4 Gauge for checking the maximum withdrawal force (see 15.2) . 26
D.2.5 Gauges for checking the minimum withdrawal force (see 15.3) . 26
D.2.6 Position of switch cam of optional micro switches . 27
Bibliography . 28
Figure D.1 – Appliance inlet . 19
Figure D.2 – Connector . 21
Figure D.3 – Positioning of the “+” and “−” pins/connector-contacts . 22
Figure D.4 – Gauges for checking point of first contact . 23
Figure D.5 – "GO" gauges for appliance inlets according to standard sheet 1
(Figure D.1) . 24
Figure D.6 – "GO" gauges for connector according to standard sheet 2 (Figure D.2). 25
Figure D.7 – Gauge representing the counterpart inlet designed to accept DC only for
checking the maximum withdrawal force, for breaking capacity test and for normal
operation test . 26
Figure D.8 – Gauge for checking the minimum withdrawal force for “+” and “–”
connector-contact . 26
Figure D.9 – Gauge for checking the minimum withdrawal force for “+”, “–” and “PE”
socket-contact . 27
Table 1 – Relationship between rated power and connectable nominal cross-sectional
areas or American Wire Gauges (AWG) size of copper conductors . 8
Table 2 – Maximum diameters of the cords . 9
Table 3 – Maximum and minimum withdrawal forces . 9
Table 4 – Cords and conductors for the tests of Clause 21 . 11
Table 5 – Type and nominal cross-sectional area of cords . 11
Table 6 – Types of cable for the rewirable connector test. 11
Table 7 – Value for the lateral pulls applied . 12
Table 8 – Values for straight and lateral pull forces . 12
Table D.1 – Dimension of contact gauge . 23
– 4 – IEC TS 63236-2:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DIRECT CURRENT (DC) APPLIANCE COUPLERS FOR INFORMATION
AND COMMUNICATION TECHNOLOGY (ICT) EQUIPMENT INSTALLED
IN DATA CENTRES AND TELECOM CENTRAL OFFICES –
Part 2: 5,2 kW system
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.