Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments

This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or product-family EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and light-industrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements. Requirements are specified for each port considered.

Compatibilité électromagnétique (CEM) - Partie 6-3: Normes génériques - Norme sur l'émission pour les environnements résidentiels, commerciaux et de l'industrie légère

La présente partie de la CEI 61000 concernant les exigences d'émissions en matière de compatibilité électromagnétique s'applique aux appareils électriques et électroniques destinés à être utilisés dans des environnements résidentiels, commerciaux et de l'industrie légère. Les exigences d'émissions dans la gamme de fréquences de 0 kHz à 400 GHz sont couvertes. Il n'est pas nécessaire de réaliser des mesures aux fréquences pour lesquelles aucune exigence n'a été spécifiée. Cette norme d'émission CEM générique s'applique en l'absence de norme applicable d'émission CEM spécifique à un produit ou à une famille de produits. Cette norme s'applique aux appareils destinés à être raccordés directement au réseau public d'alimentation basse tension ou à une source de courant continu spécifique destinée à servir d'interface entre l'appareil et le réseau public d'alimentation basse tension. Cette norme s'applique également aux appareils alimentés par piles ou batteries ou par un système de distribution basse tension non public mais non industriel, lorsque cet appareil est destiné à être utilisé dans les emplacements décrits ci-dessous. Les environnements couverts par cette norme sont les sites résidentiels, les locaux commerciaux et de l'industrie légère, à la fois intérieurs et extérieurs. La liste suivante, bien que non exhaustive, donne une indication sur les sites qui sont couverts: - propriétés résidentielles, par exemple maisons, appartements ; - lieux de vente au détail, par exemple boutiques, supermarchés; - centres d'affaires, par exemple bureaux, banques; - locaux de loisirs recevant du public, par exemple cinémas, bars, dancings; - sites extérieurs, par exemple stations service, parcs de stationnement, centres de loisirs et centres sportifs; - locaux de l'industrie légère, par exemple ateliers, laboratoires, centres de services. Les sites qui sont caractérisés comme étant alimentés directement en basse tension par le réseau public sont considérés comme résidentiels, commerciaux ou pour l'industrie légère. L'objet de cette norme est de définir les exigences d'essais d'émissions aux perturbations continues et transitoires, conduites et rayonnées, pour les appareils définis dans le domaine d'application. Les exigences des perturbations émises ont été choisies de manière à assurer que les perturbations engendrées par l'appareil en fonctionnement normal, dans un environnement résidentiel, commercial ou de l'industrie légère, ne dépassent pas un niveau qui pourrait empêcher d'autres appareils de fonctionner comme prévu normalement. Les conditions de défaut de l'appareil ne sont pas prises en compte. Cette norme ne comporte pas, pour les besoins des essais, tous les phénomènes perturbateurs mais uniquement ceux considérés comme applicables pour les appareils couverts par la norme. Ces exigences représentent les exigences essentielles de compatibilité électromagnétique concernant les émissions. Les exigences sont spécifiées pour chacun des accès considérés.

General Information

Status
Published
Publication Date
16-Feb-2011
Current Stage
DELPUB - Deleted Publication
Completion Date
30-Jul-2020
Ref Project

Relations

Buy Standard

Standard
IEC 61000-6-3:2006 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments Released:7/17/2006
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
IEC 61000-6-3:2006 - Compatibilité électromagnétique (CEM) - Partie 6-3: Normes génériques - Norme sur l'émission pour les environnements résidentiels, commerciaux et de l'industrie légère Released:7/17/2006
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
IEC 61000-6-3:2006 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
English and French language
27 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
IEC 61000-6-3:2006+AMD1:2010 CSV - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments Released:2/17/2011 Isbn:9782889123360
English and French language
41 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL
IEC
ELECTROTECHNICAL
61000-6-3
COMMISSION
Second edition
2006-07
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
Electromagnetic compatibility (EMC) –
Part 6-3:
Generic standards –
Emission standard for residential, commercial
and light-industrial environments

This English-language version is derived from the original
bilingual publication by leaving out all French-language
pages. Missing page numbers correspond to the French-
language pages.
Reference number
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the

60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.

Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,

edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the

base publication incorporating amendment 1 and the base publication incorporating

amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to
search by a variety of criteria including text searches, technical committees
and date of publication. On-line information is also available on recently issued
publications, withdrawn and replaced publications, as well as corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/online_news/ justpub)
is also available by email. Please contact the Customer Service Centre (see
below) for further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:

Email: custserv@iec.ch
Tel: +41 22 919 02 11
Fax: +41 22 919 03 00
INTERNATIONAL
IEC
ELECTROTECHNICAL
61000-6-3
COMMISSION
Second edition
2006-07
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
Electromagnetic compatibility (EMC) –
Part 6-3:
Generic standards –
Emission standard for residential, commercial
and light-industrial environments

© IEC 2006 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale N
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue

61000-6-3  IEC:2006 – 3 –
CONTENTS
FOREWORD.5

INTRODUCTION.9

1 Scope and object.11

2 Normative references .13

3 Terms and definitions .15

4 Conditions during testing .17

5 Product documentation.17
6 Applicability.19
7 Emission requirements .19
8 Application of limits in tests for conformity of equipment in series production .19
9 Measurement uncertainty .21

Bibliography.27

Figure 1 – Examples of ports .15

Table 1 − Emission .23

61000-6-3  IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION

INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE

___________
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,

commercial and light-industrial environments

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61000-6-3 has been prepared by CISPR subcommittee H: Limits
for the protection of radio services.
This second edition cancels and replaces the first edition published in 1996 as
CISPR/IEC 61000-6-3. It constitutes a technical revision. The major changes in this edition
are the inclusion of a clause on tests for equipment in series production, a new clause on
measurement uncertainty and the inclusion of requirements on dc power ports and
telecommunications ports. The informative annex has been deleted.

61000-6-3  IEC:2006 – 7 –
The text of this standard is based on the following documents:

FDIS Report on voting
CISPR/H/121/FDIS CISPR/H/124/RVD

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61000-6-3  IEC:2006 – 9 –
INTRODUCTION
IEC 61000 is published in separate parts according to the following structure:

Part 1: General
General considerations (introduction, fundamental principles)

Definitions, terminology
Part 2: Environment
Description of the environment
Classification of the environment
Compatibility levels
Part 3: Limits
Emission limits
Immunity limits (insofar as they do not fall under the responsibility of the product
committees)
Part 4: Testing and measurement techniques
Measurement techniques
Testing techniques
Part 5: Installation and mitigation guidelines
Installation guidelines
Mitigation methods and devices
Part 6: Generic standards
Part 9: Miscellaneous
Each part is further subdivided into several parts published either as International Standards
or technical reports/specifications, some of which have already been published as sections.
Others will be published with the part number followed by a dash and a second number
identifying the subdivision (example: 61000-6-1).

61000-6-3  IEC:2006 – 11 –
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,

commercial and light-industrial environments

1 Scope and object
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic
apparatus intended for use in residential, commercial and light-industrial environments.
Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No
measurement needs to be performed at frequencies where no requirement is specified.
This generic EMC emission standard is applicable if no relevant dedicated product or product-
family EMC emission standard exists.
This standard applies to apparatus intended to be directly connected to a low-voltage public
mains network or connected to a dedicated DC source, which is intended to interface between
the apparatus and the low-voltage public mains network. This standard applies also to
apparatus which is battery operated or is powered by a non-public, but non-industrial, low-
voltage power distribution system if this apparatus is intended to be used in the locations
described below.
The environments encompassed by this standard are residential, commercial and light-
industrial locations, both indoor and outdoor. The following list, although not comprehensive,
gives an indication of locations that are included:
– residential properties, for example houses, apartments;
– retail outlets, for example shops, supermarkets;
– business premises, for example offices, banks;
– areas of public entertainment, for example cinemas, public bars, dance halls;
– outdoor locations, for example petrol stations, car parks, amusement and sports centres;
– light-industrial locations, for example workshops, laboratories, service centres.
Locations that are characterised by being supplied directly at low voltage from the public

mains network are considered to be residential, commercial or light-industrial.
The object of this standard is to define the emission test requirements for apparatus defined
in the scope in relation to continuous and transient, conducted and radiated disturbances.
The emission requirements have been selected so as to ensure that disturbances generated
by apparatus operating normally in residential, commercial and light-industrial locations do
not exceed a level which could prevent other apparatus from operating as intended. Fault
conditions of apparatus are not taken into account. Not all disturbance phenomena have been
included for testing purposes in this standard but only those considered as relevant for the
equipment covered by this standard. These requirements represent essential electromagnetic
compatibility emission requirements.

61000-6-3  IEC:2006 – 13 –
Requirements are specified for each port considered.

NOTE 1 Safety considerations are not covered by this standard.

NOTE 2 In special cases, situations will arise where the levels specified in this standard will not offer adequate

protection; for example where a sensitive receiver is used in close proximity to an apparatus. In these instances,

special mitigation measures may have to be employed.

NOTE 3 As the requirements in this standard are more stringent than the requirements in IEC 61000
...


COMMISSION
CEI
ÉLECTROTECHNIQUE
61000-6-3
INTERNATIONALE
Deuxième édition
2006-07
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
Compatibilité électromagnétique (CEM) –
Partie 6-3:
Normes génériques –
Norme sur l’émission pour les environnements
résidentiels, commerciaux et de l’industrie légère

Cette version française découle de la publication d’origine
bilingue dont les pages anglaises ont été supprimées.
Les numéros de page manquants sont ceux des pages
supprimées.
Numéro de référence
CEI 61000-6-3:2006(F)
Numérotation des publications
Depuis le 1er janvier 1997, les publications de la CEI sont numérotées à partir de

60000. Ainsi, la CEI 34-1 devient la CEI 60034-1.

Editions consolidées
Les versions consolidées de certaines publications de la CEI incorporant les

amendements sont disponibles. Par exemple, les numéros d’édition 1.0, 1.1 et 1.2

indiquent respectivement la publication de base, la publication de base incorporant

l’amendement 1, et la publication de base incorporant les amendements 1 et 2

Informations supplémentaires sur les publications de la CEI
Le contenu technique des publications de la CEI est constamment revu par la CEI
afin qu'il reflète l'état actuel de la technique. Des renseignements relatifs à cette
publication, y compris sa validité, sont disponibles dans le Catalogue des
publications de la CEI (voir ci-dessous) en plus des nouvelles éditions, amende-
ments et corrigenda. Des informations sur les sujets à l’étude et l’avancement des
travaux entrepris par le comité d’études qui a élaboré cette publication, ainsi que la
liste des publications parues, sont également disponibles par l’intermédiaire de:
• Site web de la CEI (www.iec.ch)
• Catalogue des publications de la CEI
Le catalogue en ligne sur le site web de la CEI (www.iec.ch/searchpub) vous permet
de faire des recherches en utilisant de nombreux critères, comprenant des
recherches textuelles, par comité d’études ou date de publication. Des informations
en ligne sont également disponibles sur les nouvelles publications, les publications
remplacées ou retirées, ainsi que sur les corrigenda.
• IEC Just Published
Ce résumé des dernières publications parues (www.iec.ch/online_news/justpub)
est aussi disponible par courrier électronique. Veuillez prendre contact avec le
Service client (voir ci-dessous) pour plus d’informations.
• Service clients
Si vous avez des questions au sujet de cette publication ou avez besoin de
renseignements supplémentaires, prenez contact avec le Service clients:
Email: custserv@iec.ch
Tél: +41 22 919 02 11
Fax: +41 22 919 03 00
COMMISSION
CEI
ÉLECTROTECHNIQUE
61000-6-3
INTERNATIONALE
Deuxième édition
2006-07
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
Compatibilité électromagnétique (CEM) –
Partie 6-3:
Normes génériques –
Norme sur l’émission pour les environnements
résidentiels, commerciaux et de l’industrie légère

© IEC 2006 Droits de reproduction réservés
Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun
procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale N
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur

– 2 – 61000-6-3  CEI:2006
SOMMAIRE
AVANT-PROPOS.4

INTRODUCTION.8

1 Domaine d’application et objet.10

2 Références normatives.12

3 Termes et définitions .14

4 Conditions pendant l'essai.16

5 Documentation du produit.16
6 Applicabilité.18
7 Exigences pour l'émission .18
8 Application des limites dans les essais de conformité des équipements en séries
production .18
9 Incertitude de mesure.20

Bibliographie.26

Figure 1 – Exemples d'accès .14

Tableau 1 – Émission .22

– 4 – 61000-6-3  CEI:2006
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE

COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES

___________
COMPATIBILITÉ ÉLECTROMAGNÉTIQUE (CEM) –

Partie 6-3: Normes génériques –

Norme sur l’émission pour les environnements résidentiels,

commerciaux et de l’industrie légère

AVANT-PROPOS
1) La Commission Electrotechnique Internationale (CEI) est une organisation mondiale de normalisation
composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de la CEI). La CEI a
pour objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les
domaines de l'électricité et de l'électronique. A cet effet, la CEI – entre autres activités – publie des Normes
internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au
public (PAS) et des Guides (ci-après dénommés "Publication(s) de la CEI"). Leur élaboration est confiée à des
comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les
organisations internationales, gouvernementales et non gouvernementales, en liaison avec la CEI, participent
également aux travaux. La CEI collabore étroitement avec l'Organisation Internationale de Normalisation (ISO),
selon des conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de la CEI concernant les questions techniques représentent, dans la mesure
du possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de la CEI
intéressés sont représentés dans chaque comité d’études.
3) Les Publications de la CEI se présentent sous la forme de recommandations internationales et sont agréées
comme telles par les Comités nationaux de la CEI. Tous les efforts raisonnables sont entrepris afin que la CEI
s'assure de l'exactitude du contenu technique de ses publications; la CEI ne peut pas être tenue responsable
de l'éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final.
4) Dans le but d'encourager l'uniformité internationale, les Comités nationaux de la CEI s'engagent, dans toute la
mesure possible, à appliquer de façon transparente les Publications de la CEI dans leurs publications
nationales et régionales. Toutes divergences entre toutes Publications de la CEI et toutes publications
nationales ou régionales correspondantes doivent être indiquées en termes clairs dans ces dernières.
5) La CEI n’a prévu aucune procédure de marquage valant indication d’approbation et n'engage pas sa
responsabilité pour les équipements déclarés conformes à une de ses Publications.
6) Tous les utilisateurs doivent s'assurer qu'ils sont en possession de la dernière édition de cette publication.
7) Aucune responsabilité ne doit être imputée à la CEI, à ses administrateurs, employés, auxiliaires ou
mandataires, y compris ses experts particuliers et les membres de ses comités d'études et des Comités
nationaux de la CEI, pour tout préjudice causé en cas de dommages corporels et matériels, ou de tout autre
dommage de quelque nature que ce soit, directe ou indirecte, ou pour supporter les coûts (y compris les frais
de justice) et les dépenses découlant de la publication ou de l'utilisation de cette Publication de la CEI ou de
toute autre Publication de la CEI, ou au crédit qui lui est accordé.
8) L'attention est attirée sur les références normatives citées dans cette publication. L'utilisation de publications
référencées est obligatoire pour une application correcte de la présente publication.

9) L’attention est attirée sur le fait que certains des éléments de la présente Publication de la CEI peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. La CEI ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et de ne pas avoir signalé leur existence.
La norme internationale CEI 61000-6-3 a été préparée par le sous-comité H du CISPR:
Limites pour la protection des services radioélectriques.
Cette deuxième édition annule et remplace la première édition publiée en 1996 comme
CISPR/CEI 61000-6-3. Cette édition constitue une révision technique. Les principaux
changements introduits par cette nouvelle édition consistent dans l’ajout de deux nouveaux
articles, le premier sur les essais applicables aux appareils produits en série, le second
concernant l’incertitude de mesure, et dans l’insertion d’exigences sur les accès
d’alimentation en courant continu et les accès de télécommunication. L’annexe informative a
par ailleurs été supprimée.
– 6 – 61000-6-3  CEI:2006
Le texte de cette norme est issu des documents suivants:

FDIS Rapport de vote
CISPR/H/121/FDIS CISPR/H/124/RVD

Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant

abouti à l'approbation de cette norme.

Cette publication a été rédigée selon les Directives ISO/CEI, Partie 2.

Le comité a décidé que le contenu de cette publication ne sera pas modifié avant la date de
maintenance indiquée sur le site web de la CEI sous "http://webstore.iec.ch" dans les
données relatives à la publication recherchée. A cette date, la publication sera
• reconduite,
• supprimée,
• remplacée par une édition révisée, ou
• amendée.
– 8 – 61000-6-3  CEI:2006
INTRODUCTION
La CEI 61000 est publiée sous forme de plusieurs parties, conformément à la structure

suivante:
Partie 1: Généralités
Considérations générales (introduction, principes fondamentaux)

Définitions, terminologie
Partie 2: Environnement
Description de l'environnement
Classification de l'environnement
Niveaux de compatibilité
Partie 3: Limites
Limites d'émission
Limites d'immunité (dans la mesure où elles ne relèvent pas des comités de produit)
Partie 4: Techniques d’essai et de mesure
Techniques de mesure
Techniques d'essai
Partie 5: Directives d'installation et d'atténuation
Guides d'installation
Méthodes et dispositifs d'atténuation
Partie 6: Normes génériques
Partie 9: Divers
Chaque partie est à son tour subdivisée en parties qui sont publiées soit comme Normes
internationales, soit comme rapports techniques/spécifications techniques, certaines d'entre
elles ont déjà été publiées comme sections. D'autres seront publiées avec le numéro de la
partie suivi d’un tiret et complété d'un second chiffre identifiant la subdivision (exemple:
61000-6-1).
– 10 – 61000-6-3  CEI:2006
COMPATIBILITÉ ÉLECTROMAGNÉTIQUE (CEM) –

Partie 6-3: Normes génériques –

Norme sur l’émission pour les environnements résidentiels,

commerciaux et de l'industrie légère

1 Domaine d’application et objet

La présente partie de la CEI 61000 concernant les exigences d’émissions en matière de
compatibilité électromagnétique s'applique aux appareils électriques et électroniques destinés
à être utilisés dans des environnements résidentiels, commerciaux et de l'industrie légère.
Les exigences d’émissions dans la gamme de fréquences de 0 kHz à 400 GHz sont
couvertes. Il n’est pas nécessaire de réaliser des mesures aux fréquences pour lesquelles
aucune exigence n’a été spécifiée.
Cette norme d’émission CEM générique s'applique en l'absence de norme applicable
d’émission CEM spécifique à un produit ou à une famille de produits.
Cette norme s'applique aux appareils destinés à être raccordés directement au réseau public
d’alimentation basse tension ou à une source de courant continu spécifique destinée à servir
d'interface entre l'appareil et le réseau public d’alimentation basse tension. Cette norme
s'applique également aux appareils alimentés par piles ou batteries ou par un système de
distribution basse tension non public mais non industriel, lorsque cet appareil est destiné à
être utilisé dans les emplacements décrits ci-dessous.
Les environnements couverts par cette norme sont les sites résidentiels, les locaux
commerciaux et de l'industrie légère, à la fois intérieurs et extérieurs. La liste suivante, bien
que non exhaustive, donne une indication sur les sites qui sont couverts:
– propriétés résidentielles, par exemple maisons, appartements;
– lieux de vente au détail, par exemple boutiques, supermarchés;
– centres d'affaires, par exemple bureaux, banques;
– locaux de loisirs recevant du public, par exemple cinémas, bars, dancings;
– sites extérieurs, par exemple stations service, parcs de stationnement, centres de loisirs
et centres sportifs;
– locaux de l'industrie légère, par exemple ateliers, laboratoires, centres de services.
Les sites qui sont caractérisés comme étant alimentés directement en basse
...


IEC 61000-6-3
Edition 2.0 2006-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial
and light-industrial environments

Compatibilité électromagnétique (CEM) –
Partie 6-3: Normes génériques – Norme sur l'émission pour les environnements
résidentiels, commerciaux et de l'industrie légère

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61000-6-3
Edition 2.0 2006-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial
and light-industrial environments

Compatibilité électromagnétique (CEM) –
Partie 6-3: Normes génériques – Norme sur l'émission pour les environnements
résidentiels, commerciaux et de l'industrie légère

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
N
CODE PRIX
ICS 33.100.10 ISBN 2-8318-8695-3

61000-6-3  IEC:2006 – 3 – – 2 – 61000-6-3 © IEC:2006
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope and object.6
2 Normative references .7
3 Terms and definitions .8
4 Conditions during testing .9
5 Product documentation.9
6 Applicability.10
7 Emission requirements .10
8 Application of limits in tests for conformity of equipment in series production .10
9 Measurement uncertainty .11

Bibliography.14

Figure 1 – Examples of ports .8

Table 1 − Emission .12

61000-6-3 © IEC:200661000-6-3  IEC:2006 – 5 – – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
___________
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,
commercial and light-industrial environments

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61000-6-3 has been prepared by CISPR subcommittee H: Limits
for the protection of radio services.
This second edition cancels and replaces the first edition published in 1996 as
CISPR/IEC 61000-6-3. It constitutes a technical revision. The major changes in this edition
are the inclusion of a clause on tests for equipment in series production, a new clause on
measurement uncertainty and the inclusion of requirements on dc power ports and
telecommunications ports. The informative annex has been deleted.

61000-6-3  IEC:2006 – 7 – – 4 – 61000-6-3 © IEC:2006
The text of this standard is based on the following documents:
FDIS Report on voting
CISPR/H/121/FDIS CISPR/H/124/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61000-6-3 © IEC:200661000-6-3  IEC:2006 – 9 – – 5 –
INTRODUCTION
IEC 61000 is published in separate parts according to the following structure:
Part 1: General
General considerations (introduction, fundamental principles)
Definitions, terminology
Part 2: Environment
Description of the environment
Classification of the environment
Compatibility levels
Part 3: Limits
Emission limits
Immunity limits (insofar as they do not fall under the responsibility of the product
committees)
Part 4: Testing and measurement techniques
Measurement techniques
Testing techniques
Part 5: Installation and mitigation guidelines
Installation guidelines
Mitigation methods and devices
Part 6: Generic standards
Part 9: Miscellaneous
Each part is further subdivided into several parts published either as International Standards
or technical reports/specifications, some of which have already been published as sections.
Others will be published with the part number followed by a dash and a second number
identifying the subdivision (example: 61000-6-1).

61000-6-3  IEC:2006 –– 6 – 11 – 61000-6-3 © IEC:2006
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,
commercial and light-industrial environments

1 Scope and object
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic
apparatus intended for use in residential, commercial and light-industrial environments.
Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No
measurement needs to be performed at frequencies where no requirement is specified.
This generic EMC emission standard is applicable if no relevant dedicated product or product-
family EMC emission standard exists.
This standard applies to apparatus intended to be directly connected to a low-voltage public
mains network or connected to a dedicated DC source, which is intended to interface between
the apparatus and the low-voltage public mains network. This standard applies also to
apparatus which is battery operated or is powered by a non-public, but non-industrial, low-
voltage power distribution system if this apparatus is intended to be used in the locations
described below.
The environments encompassed by this standard are residential, commercial and ligh
...


IEC 61000-6-3 ®
Edition 2.1 2011-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES

Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial and
light-industrial environments
Compatibilité électromagnétique (CEM) –
Partie 6-3: Normes génériques – Norme sur l'émission pour les environnements
résidentiels, commerciaux et de l'industrie légère

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or

IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.

Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette

publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61000-6-3 ®
Edition 2.1 2011-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES

Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial and
light-industrial environments
Compatibilité électromagnétique (CEM) –
Partie 6-3: Normes génériques – Norme sur l'émission pour les environnements
résidentiels, commerciaux et de l'industrie légère

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX CH
ICS 33.100.10 ISBN 978-2-88912-336-0

– 1 –
SC CIS/H/Publication IEC 61000-6-3 Amend. 1 2010, Second edition/I-SH

ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential, commercial

and light-industrial environments

INTERPRETATION SHEET
This interpretation sheet has been prepared by CISPR subcommittee H: Limits for the
protection of radio services, of IEC technical committee CISPR: International special
committee on radio interference.
The text of this interpretation sheet is based on the following documents:
FDIS Report on voting
CISPR/H/217/FDIS CISPR/H/222/RVD

Full information on the voting for the approval of this interpretation sheet can be found in the
report on voting indicated in the above table.
___________
Interpretation
The requirement in Clause 8 “Measurement uncertainty” of IEC 61000-6-3 Amend. 1 ed. 2.0:
8 Measurement uncertainty
The measurement instrumentation uncertainty shall be determined according to CISPR
16-4-2, where applicable.
NOTE For a given test method, the actual value of U has only to be recorded in the test report if the
lab
value is greater than U .
CISPR
shall be interpreted as follows:

The measurement instrumentation uncertainty shall be calculated and compared with the
budgets defined in CISPR 16-4-2. For each applicable test method, whose instrumentation
uncertainty budgets are higher than those defined in CISPR 16-4-2, compliance with the limits
has to be determined according to CISPR 16-4-2 methodology. This requirement is only
applicable for tests where an uncertainty budget is defined in CISPR 16-4-2.
The additional note was further clarification that there is no need to state in the test report the
laboratory uncertainty budget U if this is less than or equal to the U defined in CISPR
lab CISPR
16-4-2. However, it has to be mentioned in the test report that the instrumentation
measurement uncertainty is determined according to CISPR16-4-2.

July 2011 ICS 33.100.10 French text overleaf

– 2 – 61000-6-3 © IEC:2006+A1:2010

CONTENTS
FOREWORD . 3

INTRODUCTION . 5

1 Scope and object . 6

2 Normative references . 7

3 Terms, definitions and abbreviations . 8

4 Conditions during testing . 10

5 Product documentation . 10
6 Applicability . 10
7 Emission requirements . 11
8 Application of limits in tests for conformity of equipment in series production
Measurement uncertainty . 11
9 Measurement uncertainty Application of limits in tests for conformity of equipment
in series production . 12
10 Compliance with this standard . 12
11 Emission test requirements . 16

Bibliography . 21

Figure 1 – Examples of ports Ports covered by Tables 1 to 4 . 8

Table 1 – Emission – Enclosure port . 16
Table 2 – Emission – Low voltage AC mains port . 18
Table 3 – Emission – DC power port . 19
Table 4 – Emission – Telecommunications/network port . 20

61000-6-3 © IEC:2006+A1:2010 – 3 –

INTERNATIONAL ELECTROTECHNICAL COMMISSION

INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE

___________
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,

commercial and light-industrial environments

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

This consolidated version of IEC 61000-6-3 consists of the second edition (2006)
[documents CISPR/H/121/FDIS and CISPR/H/124/RVD] and its amendment 1 (2010)
[documents CISPR/H/206/FDIS and CISPR/H/210/RVD]. It bears the edition number 2.1.
The technical content is therefore identical to the base edition and its amendment and
has been prepared for user convenience. A vertical line in the margin shows where the
base publication has been modified by amendment 1. Additions and deletion
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.