Welding consumables — Test methods — Part 2: Preparation of single-run and two-run technique test pieces and specimens in steel

This document specifies the preparation of butt weld test pieces and specimens. The test pieces and specimens are used to determine the strength and impact properties of welded joints when testing welding consumables with single-run and two-run techniques. This document is applicable to welding consumables for arc welding of steel. This document is not suitable for electro-slag or electro-gas welding.

Produits consommables pour le soudage — Méthodes d'essai — Partie 2: Préparation de pièces d'essai et d'éprouvettes en une ou deux passes en acier

Le présent document spécifie la préparation des pièces d'essai et des éprouvettes en soudage bout à bout. Les pièces d'essai et les éprouvettes sont utilisées pour déterminer les propriétés de résistance mécanique et de flexion par choc des assemblages soudés lors de l'essai des produits consommables utilisés en soudage avec une ou deux passes. Le présent document est applicable aux produits consommables destinés au soudage à l'arc de l'acier. Le présent document n'est pas adapté au soudage sous laitier ou au soudage électrogaz.

General Information

Status
Published
Publication Date
19-Aug-2020
Current Stage
6060 - International Standard published
Start Date
20-Aug-2020
Due Date
13-Feb-2021
Completion Date
20-Aug-2020
Ref Project

Relations

Buy Standard

Standard
ISO 15792-2:2020 - Welding consumables -- Test methods
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15792-2:2020 - Produits consommables pour le soudage -- Méthodes d'essai
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15792-2:2020 - Produits consommables pour le soudage -- Méthodes d'essai
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 15792-2 - Welding consumables -- Test methods
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15792-2
Second edition
2020-08
Welding consumables — Test
methods —
Part 2:
Preparation of single-run and two-run
technique test pieces and specimens
in steel
Produits consommables pour le soudage — Méthodes d'essai —
Partie 2: Préparation de pièces d'essai et d'éprouvettes en une ou deux
passes en acier
Reference number
ISO 15792-2:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 15792-2:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15792-2:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 1
5 Test plate material . 1
6 Preparation of the test piece . 2
7 Welding conditions . 3
8 Heat treatment . 3
9 Position of specimens, specimen dimensions and testing . 3
Bibliography . 6
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 15792-2:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 3, Welding consumables, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 121, Welding and allied processes, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page: https://
committee .iso .org/ sites/ tc44/ home/ interpretation .html.
This second edition cancels and replaces the first edition (ISO 15792-2:2000), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— the title and scope of this document have been changed;
— Clause 10 and Clause 11 have been deleted consequently;
— a new type 2.6 has been added to Table 1 reflecting usage in the USA;
— in Table 1, the angles in column 3, preparation, have been revised to show the bevel angle with a
footnote giving tolerances for 2.1, 2.4 and 2.5;
— in Figure 1 b), effective weld length has been added;
— Figure 2 has been revised and split into Figure 2a and Figure 2b with titles showing restrictions
for use.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 15792-2:2020(E)

Introduction
Consumables for both submerged arc welding and metal arc welding with tubular cored electrodes
can be suitable for welding by the single- or two-run technique and the methods for testing and
classification are specified. When a welding consumable is offered for use by these techniques, it should
be noted that all-weld metal test pieces may not be required by the consumable classification standard.
Test conditions prescribed and results required should not be considered to be requirements or
expectations for a procedure qualification.
© ISO 2020
...

NORME ISO
INTERNATIONALE 15792-2
Deuxième édition
2020-08
Produits consommables pour le
soudage — Méthodes d'essai —
Partie 2:
Préparation de pièces d'essai et
d'éprouvettes en une ou deux passes
en acier
Welding consumables — Test methods —
Part 2: Preparation of single-run and two-run technique test pieces
and specimens in steel
Numéro de référence
ISO 15792-2:2020(F)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 15792-2:2020(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 15792-2:2020(F)

Sommaire Page
Avant-propos .iv
Introduction .vi
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Exigences générales . 1
5 Matériau de la tôle d'essai . 2
6 Préparation de la pièce d'essai . 2
7 Conditions de soudage. 3
8 Traitement thermique . 3
9 Positions et dimensions des éprouvettes et essais . 4
Bibliographie . 6
© ISO 2020 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 15792-2:2020(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le Comité Technique ISO/TC 44, Soudage et techniques connexes,
Sous-comité SC 3, Produits consommables pour le soudage, en collaboration avec le Comité Technique
CEN/TC 121, Soudage et techniques connexes, du Comité Européen de Normalisation (CEN) conformément
à l'Accord de coopération technique entre l'ISO et le CEN (Accord de Vienne).
Il convient d’adresser tout retour d'information ou questions sur le présent document à l’organisme
national de normalisation de l’utilisateur. Une liste exhaustive de ces organismes peut être trouvée à
l’adresse www .iso .org/ members .html.
Les interprétation officielles, s’il en existe, des documents de l’ISO/TC 44 sont disponibles sur la page
suivante: https:// committee .iso .org/ sites/ tc44/ home/ interpretation .html.
Cette deuxième édition annule et remplace la première édition (ISO 15792-2:2000), qui a fait l’objet
d’une révision technique.
Les principales modifications par rapport à l’édition précédente sont les suivantes:
— le titre et le domaine d'application du présent document ont été changés;
— l'Article 10 et l'Article 11 ont été supprimés en conséquence;
— un nouveau type 2.6 a été ajouté dans le Tableau 1 pour tenir compte de l'usage aux USA;
— dans le Tableau 1, les angles dans la colonne 3, préparation, ont été révisés pour montrer l'angle du
chanfrein avec une note de bas de page donnant les tolérances pour le 2.1, le 2.4 et le 2.5;
— dans la Figure 1 b), la longueur effective de la soudure a été ajoutée;
iv © ISO 2020 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 15792-2:2020(F)

— la Figure 2 a été révisée et séparée en Figure 2a et Figure 2b avec des titres montrant les restrictions
d'utilisation.
© ISO 2020 – Tous droits réservés v

---------------------- Page: 5 ----------------------
ISO 15792-2:2020(F)

Introduction
Les produits consommables destinés au soudage à l'arc sous flux solide ou au soudage avec fil fourré
peuvent convenir pour le soudage en une seule passe ou en deux passes, et les méthodes d'essai et de
classification sont spécifiées. Il convient de noter que lorsqu'un produit consommable est proposé pour
être utilisé avec ces procédés, il est possible que la norme de classification du produit consommable
n’exige aucune pièce d'essai de métal fondu hors dilution.
Il convient de ne pas prendre en considération les conditions d'essai spécifiées et les résultats exigés
comme des exigences ou des attentes en vue d'une qualification de mode opératoire.
vi © ISO 2020 – Tous droits réservés

---------------------- Page: 6 ----------------------
NORME INTERNATIONALE ISO 15792-2:2020(F)
Produits consommables pour le soudage — Méthodes
d'essai —
Partie 2:
Préparation de pièces d'essai et d'éprouvettes en une ou
deux passes en acier
1 Domaine d'application
Le
...

PROJET DE NORME INTERNATIONALE
ISO/DIS 15792-2
ISO/TC 44/SC 3 Secrétariat: ANSI
Début de vote: Vote clos le:
2019-11-13 2020-02-05
Produits consommables pour le soudage — Méthodes
d'essai —
Partie 2:
Préparation d'éprouvettes en une ou deux passes en acier
Welding consumables — Test methods —
Part 2: Preparation of single-run and two-run technique test specimens in steel
ICS: 25.160.20
CE DOCUMENT EST UN PROJET DIFFUSÉ POUR
OBSERVATIONS ET APPROBATION. IL EST DONC
SUSCEPTIBLE DE MODIFICATION ET NE PEUT
Le présent document est distribué tel qu’il est parvenu du secrétariat du comité.
ÊTRE CITÉ COMME NORME INTERNATIONALE
AVANT SA PUBLICATION EN TANT QUE TELLE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES
FINS INDUSTRIELLES, TECHNOLOGIQUES ET
COMMERCIALES, AINSI QUE DU POINT DE VUE TRAITEMENT PARALLÈLE ISO/CEN
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR
POSSIBILITÉ DE DEVENIR DES NORMES
POUVANT SERVIR DE RÉFÉRENCE DANS LA
RÉGLEMENTATION NATIONALE.
Numéro de référence
LES DESTINATAIRES DU PRÉSENT PROJET
ISO/DIS 15792-2:2019(F)
SONT INVITÉS À PRÉSENTER, AVEC LEURS
OBSERVATIONS, NOTIFICATION DES DROITS
DE PROPRIÉTÉ DONT ILS AURAIENT
ÉVENTUELLEMENT CONNAISSANCE ET À
©
FOURNIR UNE DOCUMENTATION EXPLICATIVE. ISO 2019

---------------------- Page: 1 ----------------------
ISO/DIS 15792-2:2019(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2019
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2019 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/DIS 15792-2:2019(F)
Sommaire
Avant-propos . iv
Introduction. v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Exigences générales . 1
5 Matériau de la tôle d'essai . 1
6 Préparation de la pièce d'essai . 2
7 Conditions de soudage . 2
8 Traitement thermique . 2
9 Positions et dimensions des éprouvettes et essais . 2
10 Contre-essais . 3
11 Rapport d'essai . 6

© ISO 2019 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO/DIS 15792-2:2019(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L'élaboration des Normes internationales est en
général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit
de faire partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales
et non gouvernementales, en liaison avec l'ISO participent également aux travaux. L’ISO collabore
étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne la
normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L’attention est attirée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l'élaboration
du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de brevets reçues par
l’ISO (voir www.iso.org/patents).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www.iso.org/iso/foreword.html.
Le présent document a été élaboré par le comité technique ISO/TC 44, Soudage et techniques connexes,
Souscomité SC 3, Produits consommables pour le soudage.
Il convient d’adresser tout retour d'information ou questions sur le présent document à l’organisme
national de normalisation de l’utilisateur. Une liste exhaustive de ces organismes peut être trouvée à
l’adresse www.iso.org/members.html.
Les interprétation officielles, s’il en existe, des documents de l’ISO/TC 44 sont disponibles sur la page
suivante : https://committee.iso.org/sites/tc44/home/interpretation.html.
Cette deuxième édition annule et remplace la première édition (ISO 15792-2:2000), qui a fait l’objet d’une
révision technique.
Les principales modifications par rapport à l’édition précédente sont les suivantes :
— A compléter avant la publication
iv © ISO 2019 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO/DIS 15792-2:2019(F)
Introduction
Les produits consommables destinés au soudage à l'arc sous flux solide ou au soudage avec fil fourré
peuvent convenir pour le soudage en une seule passe ou en deux passes, et les méthodes d'essai et de
classification sont spécifiées. Il convient de noter que lorsqu'un produit consommable est proposé pour
être utilisé avec ces procédés, il est possible que la norme de classification du produit consommable
n’exige aucune pièce d'essai de métal fondu hors dilution.
Il convient de ne pas prendre en considération les conditions d'essai prescrites et les résultats exigés
comme des exigences ou des attentes en vue d'une qualification de mode opératoire.

© ISO 2019 – Tous droits réservés v

---------------------- Page: 5 ----------------------
ISO/DIS 15792-2:2019(F)
Produits consommables pour le soudage — Méthodes d'essai —
Partie 2: Préparation d'éprouvettes en une ou deux passes en
acier
1 Domaine d'application
Le présent document spécifie la préparation des pièces d'essai en soudage bout à bout et des éprouvettes.
Il a pour objet de définir les méthodes employées afin de déterminer la résistance mécanique et la
résilience de l’assemblage soudé lors de l'essai des produits consommables utilisés en soudage avec une
ou deux passes, et non adapté au soudage sous laitier ou au soudage électrogaz.
Le présent document est applicable aux produits consommables destinés au soudage à l'arc de l'acier.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou pa
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 15792-2
ISO/TC 44/SC 3 Secretariat: ANSI
Voting begins on: Voting terminates on:
2019-11-13 2020-02-05
Welding consumables — Test methods —
Part 2:
Preparation of single-run and two-run technique test
specimens in steel
Produits consommables pour le soudage — Méthodes d'essai —
Partie 2: Préparation d'éprouvettes en une ou deux passes en acier
ICS: 25.160.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15792-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 1 ----------------------
ISO/DIS 15792-2:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 15792-2:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 1
5 Test plate material . 1
6 Preparation of the test piece . 2
7 Welding conditions . 2
8 Heat treatment . 2
9 Position of specimens, specimen dimensions and testing . 2
10 Retests . 3
11 Test report . 6
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 15792-2:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes],
Subcommittee SC 3, Welding consumables.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
Official interpretations of TC 44 documents, where they exist, are available from this page: https:
//committee .iso .org/sites/tc44/home/interpretation .html.
This second edition cancels and replaces the first edition (ISO 15792-2:2000), which has been
technically revised.
A list of all parts in the ISO 15792 series can be found on the ISO website.
The main changes compared to the previous edition are as follows:
— To be completed before publication
iv © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/DIS 15792-2:2019(E)

Introduction
Consumables for both submerged arc welding and metal arc welding with tubular cored electrodes
can be suitable for welding by the single- or two-run technique and the methods for testing and
classification are specified. When a welding consumable is offered for use by these techniques, it should
be noted that all-weld metal test pieces may not be required by the consumable classification standard.
Test conditions prescribed and results required should not be considered to be requirements or
expectations for a procedure qualification.
© ISO 2019 – All rights reserved v

---------------------- Page: 5 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 15792-2:2019(E)
Weld
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.