Geometrical Product Specifications (GPS) — Standard reference temperature for geometrical product specification and verification

This International Standard specifies the standard reference temperature for geometrical product specifications.

Spécification géométrique des produits (GPS) — Température normale de référence pour la spécification géométrique des produits et vérification

L'ISO 1 spécifie la température normale de référence pour la spécification géométrique des produits.

Specifikacija geometrijskih veličin izdelka - Standardna referenčna temperatura za specifikacijo in overjanje geometrijskih veličin izdelka

General Information

Status
Withdrawn
Publication Date
24-Jul-2002
Withdrawal Date
24-Jul-2002
Current Stage
9599 - Withdrawal of International Standard
Completion Date
26-Aug-2016

Relations

Buy Standard

Standard
ISO 1:2002 - Geometrical Product Specifications (GPS) -- Standard reference temperature for geometrical product specification and verification
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 1:2002
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 1:2002 - Spécification géométrique des produits (GPS) -- Température normale de référence pour la spécification géométrique des produits et vérification
French language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1
Second edition
2002-07-15


Geometrical Product Specifications
(GPS) — Standard reference temperature
for geometrical product specification and
verification
Spécification géométrique des produits (GPS) — Température normale de
référence pour la spécification géométrique des produits et vérification




Reference number
ISO 1:2002(E)
©
 ISO 2002

---------------------- Page: 1 ----------------------
ISO 1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and
verification.
This second edition cancels and replaces the first edition (ISO 1:1975), which has been technically revised.
Specifically, the following points have changed:
 the standard reference temperature has been modified; consequently, the title has been changed, and
 the footnote, referring to a definition of the metre which no longer exists, has been deleted.
Annex A is for information only.
© ISO 2002 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 1:2002(E)
Introduction
This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a global
GPS standard (see ISO/TR 14638). It influences all links in all chains of standards.
For more detailed information on the relationship of this International Standard to other standards and the GPS
matrix model, see annex A.
The standard referen
...

SLOVENSKI STANDARD
SIST ISO 1:2002
01-december-2002
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND6WDQGDUGQDUHIHUHQþQDWHPSHUDWXUD]D
VSHFLILNDFLMRLQRYHUMDQMHJHRPHWULMVNLKYHOLþLQL]GHOND
Geometrical Product Specifications (GPS) -- Standard reference temperature for
geometrical product specification and verification
Spécification géométrique des produits (GPS) -- Température normale de référence pour
la spécification géométrique des produits et vérification
Ta slovenski standard je istoveten z: ISO 1:2002
ICS:
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
SIST ISO 1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 1:2002

---------------------- Page: 2 ----------------------

SIST ISO 1:2002


INTERNATIONAL ISO
STANDARD 1
Second edition
2002-07-15


Geometrical Product Specifications
(GPS) — Standard reference temperature
for geometrical product specification and
verification
Spécification géométrique des produits (GPS) — Température normale de
référence pour la spécification géométrique des produits et vérification




Reference number
ISO 1:2002(E)
©
 ISO 2002

---------------------- Page: 3 ----------------------

SIST ISO 1:2002
ISO 1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 1:2002
ISO 1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and
verification.
This second edition cancels and replaces the first edition (ISO 1:1975), which has been technically revised.
Specifically, the following points have changed:
 the standard reference temperature has been modified; consequently, the title has been changed, and
 the footnote, referring to a definition of the metre which no longer exists, has been deleted.
Annex A is for
...

NORME ISO
INTERNATIONALE 1
Deuxième édition
2002-07-15



Spécification géométrique des produits
(GPS) — Température normale de référence
pour la spécification géométrique des
produits et vérification
Geometrical Product Specifications (GPS) — Standard reference
temperature for geometrical product specification and verification




Numéro de référence
ISO 1:2002(F)
©
 ISO 2002

---------------------- Page: 1 ----------------------
ISO 1:2002(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2002
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse

ii © ISO 2002 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 1:2002(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 3.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur publication
comme Normes internationales requiert l'approbation de 75 % au moins des comités membres votants.
L'attention est appelée sur le fait que certains des éléments de la présente Norme internationale peuvent faire
l'objet de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 1 a été élaborée par le comité technique ISO/TC 213, Spécifications et vérification dimensionnelles et
géométriques des produits.
Cette deuxième édition annule et remplace la première édition (ISO 1:1975), dont elle constitue une révision
technique. En particulier, elle diffère sur les points suivants:
 le concept de température normale de référence a changé; en conséquence, le titre a changé, et
 la note de bas de page, qui faisait référence à une définition du mètre qui n’existe plus, a été supprimée.
L’annexe A de la présente Norme internationale est donnée uniquement à titre d’information.

© ISO 2002 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 1:2002(F)
Introduction
La présente Norme internationale est une norme de spécification géométrique des produits (GPS) qui doit être
considérée comme une norme GPS globale (voir l'ISO/TR 14638). Elle influence tous les maillons de toutes les
chaînes de normes.
Pour de plus amples informations sur la relation d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.