ISO/TS 24283-3:2022

Geotechnical investigation and testing — Qualification criteria and assessment — Part 3: Qualified enterprise

This document specifies the qualification criteria for enterprises performing sampling, testing, measuring, monitoring and installation of equipment (e.g. piezometers, borehole heat exchangers, inclinometers and extensometers) in the framework of geotechnical investigation.

Reconnaissance et essais géotechniques - Critères de qualification et évaluation — Partie 3: Entreprise qualifiée

General Information

• Status: Published
• Publication Date: 05-Jan-2022
• ICS: 03.100.30 - Management of human resources
• ICS: 93.020 - Earthworks. Excavations. Foundation construction. Underground works
• Technical Committee: ISO/TC 182 - Geotechnics
• Drafting Committee: ISO/TC 182/WG 4 - Drilling and sampling methods and groundwater measurements
• Current Stage: 6060 - International Standard published
• Start Date: 06-Jan-2022
• Due Date: 15-Jul-2022
• Completion Date: 06-Jan-2022

Relations

• Revises: ISO/TS 22475-3:2007 - Geotechnical investigation and testing — Sampling methods and groundwater measurements — Part 3: Conformity assessment of enterprises and personnel by third party
• Effective Date: 06-Jun-2022
• Consolidates: ISO 15037-1:2019 - Road vehicles — Vehicle dynamics test methods — Part 1: General conditions for passenger cars
• Effective Date: 06-Jun-2022

Standards Content (Sample)

TECHNICAL ISO/TS
SPECIFICATION 24283-3
First edition
2022-01
Geotechnical investigation and
testing — Qualification criteria and
assessment —
Part 3:
Qualified enterprise
Reconnaissance et essais géotechniques - Critères de qualification et
évaluation —
Partie 3: Entreprise qualifiée
Reference number
ISO/TS 24283-3:2022(E)
© ISO 2022

---------------------- Page: 1 ----------------------
ISO/TS 24283-3:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 24283-3:2022(E)
Contents Page
Foreword .iv
Introduction .v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Qualification criteria . .1
Annex A (informative) Assessment and re-assessment of enterprises . 3
Bibliography . 5
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/TS 24283-3:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 182, Geotechnics, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 341, Geotechnical
Investigation and Testing, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
A list of all parts in the ISO 24283 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/TS 24283-3:2022(E)
Introduction
The ISO 24283 series specifies the qualification criteria for geotechnical investigation and testing and
has three parts:
— Part 1: Qualified technician and qualified operator
— Part 2: Responsible expert
— Part 3: Qualified enterprise
The fulfilment of the technical criteria by the enterprise or the individual can be proven by:
a) a declaration of conformity by a contractor (first party control);
b) a declaration of conformity by a client (second party control);
c) a declaration of conformity by a conformity assessment body (third party control).
v
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
TECHNICAL SPECIFICATION ISO/TS 24283-3:2022(E)
Geotechnical investigation and testing — Qualification
criteria and assessment —
Part 3:
Qualified enterprise
1  Scope
This document specifies the qualification criteria for enterprises performing sampling, testing,
measuring, monitoring and installation of equipment (e.g. piezometers, borehole heat exchangers,
inclinometers and extensometers) in the framework of geotechnical investigation.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/TS 24283-1, Geotechnical investigation and testing — Qualification criteria and assessment — Part 1:
Qualified technician
ISO/TS 24283-2, Geotechnical investigation and testing — Qualification criteria and assessment — Part 2:
Responsible expert
3  Terms and definitions
For the purposes of this document, the follow
...

TECHNICAL ISO/TS
SPECIFICATION 24283-3
First edition
Geotechnical investigation and
testing — Qualification criteria and
assessment —
Part 3:
Qualified enterprise
Reconnaissance et essais géotechniques - Critères de qualification et
évaluation —
Partie 3: Entreprise qualifiée
PROOF/ÉPREUVE
Reference number
ISO/TS 24283-3:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO/TS 24283-3:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 24283-3:2021(E)

Contents Page
Foreword .iv
Introduction .v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Qualification criteria . 1
Annex A (informative) Assessment and re-assessment of enterprises . 3
Bibliography . 5
© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii

---------------------- Page: 3 ----------------------
ISO/TS 24283-3:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 182, Geotechnics, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 341, Geotechnical
Investigation and Testing, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
A list of all parts in the ISO 24283 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/TS 24283-3:2021(E)

Introduction
The ISO 24283 series specifies the qualification criteria for geotechnical investigation and testing and
has three parts:
— Part 1: Qualified technician and qualified operator
— Part 2: Responsible expert
— Part 3: Qualified enterprise
The fulfilment of the technical criteria by the enterprise or the individual can be proven by:
a) a declaration of conformity by a contractor (first party control);
b) a declaration of conformity by a client (second party control);
c) a declaration of conformity by a conformity assessment body (third party control).
© ISO 2021 – All rights reserved PROOF/ÉPREUVE v

---------------------- Page: 5 ----------------------
TECHNICAL SPECIFICATION ISO/TS 24283-3:2021(E)
Geotechnical investigation and testing — Qualification
criteria and assessment —
Part 3:
Qualified enterprise
1  Scope
This document specifies the qualification criteria for enterprises performing sampling, testing,
measuring, monitoring and installation of equipment (e.g. piezometers, borehole heat exchangers,
inclinometers and extensometers) in the framework of geotechnical investigation.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/TS 24283-1, Geotechnical investigation and testing — Qualification criteria and assessment — Part 1:
Qualified technician
ISO/TS 24283-2, Geotechnical investigation and testing — Qualification criteria and assessment — Part 2:
Responsible expert
3  Terms and definitions
For the purposes of this document, the following
...