ISO 6394:1998
(Main)Acoustics — Measurement at the operator's position of noise emitted by earth-moving machinery — Stationary test conditions
Acoustics — Measurement at the operator's position of noise emitted by earth-moving machinery — Stationary test conditions
Acoustique — Mesurage du bruit émis par les engins de terrassement au poste de conduite — Conditions d'essai statiques
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6394
Second edition
1998-11-15
Acoustics — Measurement at the operator's
position of noise emitted by earth-moving
machinery — Stationary test conditions
Acoustique — Mesurage du bruit émis par les engins de terrassement
au poste de conduite — Conditions d'essai statiques
A
Reference number
ISO 6394:1998(E)
---------------------- Page: 1 ----------------------
ISO 6394:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 6394 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 1,
Noise, in collaboration with ISO/TC 127, Earth moving machinery.
This second edition cancels and replaces the first edition (ISO 6394:1985), which has been technically revised.
Annex A forms a normative part of this International Standard.
© ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 2 ----------------------
© ISO
ISO 6394:1998(E)
Introduction
This International Standard is a special test code for specific types of earth-moving machinery. It is an extension of
ISO 11201 which contains the general requirements for many types of machinery and equipment.
Specific procedures are described in this special test code to enable the sound pressure level at the operator's
position, with the machine stationary, to be determined in a manner which is repeatable. Attachments (bucket,
dozer, etc.) for the manufacturer's production version are to be fitted, since this is the configuration most likely to
exist when the machine is in actual use.
This International Standard enables compliance with noise limits to be determined. It can also be used for
evaluation purposes in noise reduction investigations.
An additional special test code is given in ISO 6393. This other special test code is intended to be used to
determine the exterior noise emitted by earth-moving machinery while the machine is stationary, in terms of the
A-weighted sound pressure level.
Corresponding measurements of exterior noise and noise at the operator's position under dynamic test conditions
are described in ISO 6395 and ISO 6396, respectively.
iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD © ISO ISO 6394:1998(E)
Acoustics — Measurement at the operator's position of noise
emitted by earth-moving machinery — Stationary test conditions
1 Scope
This International Standard specifies a method for determining the noise emitted by earth-moving machinery,
measured at the operator's position, in terms of the time-averaged A-weighted sound pressure level while the
machine is stationary with the engine operating at rated speed under no-load conditions.
This International Standard is applicable to the following specific types of earth-moving machinery:
excavators (hydraulic or rope-operated);
crawler and wheel tractor-dozers;
crawler and wheel loaders; and
backhoe loaders (also known as excavator loaders).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 3411, Earth-moving machinery — Human physical dimensions of operators and minimum operator space
envelope.
ISO 6393, Acoustics — Measurement of exterior noise emitted by earth-moving machinery — Stationary test
conditions.
ISO 9249, Earth-moving machinery — Engine test code — Net power.
ISO 11201, Acoustics — Noise emitted by machinery and equipment — Measurement of emission sound pressure
levels at a work station and at other specified positions — Engineering method in an essentially free field over a
reflecting plane.
1)
IEC 60651, Sound level meters.
1)
IEC 60804, Integrating-averaging sound level meters.
1)
IEC 60651 and IEC 60804 will be replaced by IEC 61672.
1
---------------------- Page: 4 ----------------------
© ISO
ISO 6394:1998(E)
3 Terms and definitions
For the purposes of this International Standard, the terms and definitions given in ISO 11201 and the following apply.
For the convenience of users of this International Standard, some definitions are quoted from ISO 6165:1997.
3.1
time-averaged A-weighted sound pressure level, L
pAeq,T
A-weighted sound pressure level averaged on an energy basis over the whole measurement period, T
3.2
excavator
self-propelled machine on crawler, wheels or legs, having an upper structure normally capable of a 360� swing with
mounted equipment, primarily designed for excavating with a bucket, without moving the undercarriage during the
work cycle
NOTE An excavator work cycle normally comprises excavating, elevating, swinging and discharging material.
[ISO 6165:1997]
See Figure 1.
Figure 1 — Excavator
3.3
tractor-dozer
self-propelled crawler or wheeled machine with equipment having either a dozing attachment which cuts, moves
and grades material through forward motion of the machine, or a mounted attachment used to exert a push or a pull
force
[ISO 6165:1997]
See Figure 2.
Figure 2 — Tractor-dozer
2
---------------------- Page: 5 ----------------------
© ISO
ISO 6394:1998(E)
3.4
loader
self-propelled crawler or wheeled machine, having front-mounted equipment primarily designed for loading
operation (bucket use), which loads or excavates through forward motion of the machine
NOTE A loader work cycle normally comprises filling, elevating, transporting and discharging material.
[ISO 6165:1997]
See Figure 3.
Figure 3 — Loader
3.5
backhoe loader
self-propelled crawler or wheeled machine, having a main frame designed to carry both front-mounted equipment
and rear-mounted backhoe equipment (normally with outriggers); when used in the backhoe mode, the machine is
stationary and normally digs below ground level; when used in the loader mode (bucket use), the machine loads
through forward motion
NOTE A backhoe work cycle normally comprises excavating, elevating, swinging and discharging material. A loader work
cycle normally comprises filling, elevating, transporting and discharging material.
[ISO 6165:1997]
See Figure 4.
Figure 4 — Backhoe loader
4 Instrumentation
The instrumentation shall be capable of carrying out measurements as described in 8.1. The preferred
instrumentation system for acquiring the data is an integrating-averaging sound level meter complying with the
3
---------------------- Page: 6 ----------------------
© ISO
ISO 6394:1998(E)
requirements of IEC 60804 for a class 1 instrument. Alternative instrumentation, including the microphone and
cable, shall meet the requirements of IEC 60651 for a class 1 instrument.
NOTE The sensitivity to environmental conditions is especially relevant for this type of measurement. It is recommended to
ask the manufacturer for evidence that related tests according to IEC 60651 were carried out with a positive result.
5 Test environment
For the purposes of this International Standard, the test environment specified in ISO 6393 applies.
6 Measurement of time-averaged A-weighted sound pressure levels
6.1 Operator
6.1.1 Operator presence
The operator shall be in the driving position and observers shall not be in close proximity or in the cab during
measurements. The operator shall neither wear abnormally sound-absorptive clothing nor any hat or scarf (other
than a protective helmet used for safety reasons, or a helmet or frame used to support a microphone) which might
influence the noise measurements.
6.1.2 Operator stature
The operator shall have a sitting height between 800 mm (small operator) and 960 mm (large operator) measured
from the sitting surface to the top of the head, as specified in ISO 3411.
6.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.