Plastics — Generic identification and marking of plastics products

ISO 11469:2016 specifies a system of uniform marking of products that have been fabricated from plastics materials. Provision for the process or processes to be used for marking is outside the scope of this International Standard. NOTE 1 Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate location of the marking, are subject to agreement between the manufacturer and the user. The marking system is intended to help identify plastics products for subsequent decisions concerning handling, waste recovery or disposal. Generic identification of the plastics is provided by the symbols and abbreviated terms given in ISO 1043‑1, ISO 1043‑2, ISO 1043‑3 and ISO 1043‑4. NOTE 2 If more detailed information for material identification is needed, additional marking of plastics products can be applied as defined in the appropriate product standard. ISO 11469:2016 is not intended to supplant, replace or in any way interfere with the requirements for labelling specified in product standards or legislation.

Plastiques — Identification générique et marquage des produits en matière plastique

ISO 11469:2016 prescrit un système de marquage uniforme des produits qui été fabriqués à partir de matières plastiques. Les dispositions pour le (ou les) procédé(s) de marquage sont en dehors du domaine d'application de la présente Norme internationale. NOTE 1 Les caractéristiques précises du marquage, par exemple les dimensions minimales de l'article devant faire l'objet du marquage, les dimensions du lettrage et l'emplacement approprié auquel apposer le marquage, font l'objet d'un accord entre le fabricant et l'utilisateur. Le système de marquage est destiné à faciliter l'identification des produits en matière plastique dans l'optique de décisions à prendre ultérieurement en ce qui concerne leur manutention, leur valorisation en tant que déchets ou leur élimination. L'identification générique des plastiques est constituée par les symboles et les termes abrégés donnés dans l'ISO 1043‑1, l'ISO 1043‑2, l'ISO 1043‑3 et l'ISO 1043‑4. NOTE 2 Si l'on a besoin d'informations plus détaillées pour l'identification de la matière, on peut appliquer un marquage complémentaire sur le produit en matière plastique, conformément aux normes de produit pertinentes. ISO 11469:2016 n'a pas pour objectif de supplanter, de remplacer, ou d'interférer, de quelque manière que ce soit, avec les exigences relatives à l'étiquetage spécifiées dans les normes produit ou les législations.

General Information

Status
Published
Publication Date
22-Sep-2016
Technical Committee
Current Stage
9093 - International Standard confirmed
Completion Date
09-Sep-2022
Ref Project

Relations

Buy Standard

Standard
ISO 11469:2016 - Plastics -- Generic identification and marking of plastics products
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11469:2016 - Plastics -- Generic identification and marking of plastics products
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11469:2016 - Plastiques -- Identification générique et marquage des produits en matière plastique
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11469:2016 - Plastiques -- Identification générique et marquage des produits en matiere plastique
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11469
Third edition
2016-10-01
Plastics — Generic identification and
marking of plastics products
Plastiques — Identification générique et marquage des produits en
matière plastique
Reference number
ISO 11469:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 11469:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11469:2016(E)

Contents  Page
Foreword .iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Symbols and abbreviated terms . 2
5  Requirements . 2
5.1 Marking system . 2
5.1.1 Marking of products . 2
5.1.2 Single-constituent products . 2
5.1.3 Polymer blends or alloys . 2
5.1.4 Compositions with special additives . 3
5.2 Method of marking . 4
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11469:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 1, Terminology.
This third edition cancels and replaces the second edition (ISO 11469:2000), which has been technically
revised with the following changes:
— the definition of “plastics products” has been modified;
— the marking of recyclates has been included.
iv © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 11469:2016(E)
Plastics — Generic identification and marking of plastics
products
1  Scope
This International Standard specifies a system of uniform marking of products that have been
fabricated from plastics materials. Provision for the process or processes to be used for marking is
outside the scope of this International Standard.
NOTE 1 Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering,
the appropriate location of the marking, are subject to agreement between the manufacturer and the user.
The marking system is intended to help identify plastics products for subsequent decisions concerning
handling, waste recovery or disposal.
Generic identification of the plastics is provided by the symbols and abbreviated terms given in
ISO 1043-1, ISO 1043-2, ISO 1043-3 and ISO 1043-4.
NOTE 2 If more detailed information for material identification is needed, additional marking of plastics
products can be applied as defined in the appropriate product standard.
This International Standard is not intended to supplant, replace or in any way interfere with the
requirements for labelling specified in product standards or legislation.
2  Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references,
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 11469
ISO/TC 61/SC 1 Secretariat: BSI
Voting begins on: Voting terminates on:
2015-08-13 2015-11-13
Plastics — Generic identification and marking of plastics
products
Plastiques — Identification générique et marquage des produits en matière plastique
ICS: 83.080.01
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11469:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 1 ----------------------
ISO/DIS 11469:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 11469
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 2
5 Requirements . 2

© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 11469
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11469 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 1, Terminology.
This second/third/. edition cancels and replaces the first/second/. edition (), [clause(s) / subclause(s) /
table(s) / figure(s) / annex(es)] of which [has / have] been technically revised.

iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 11469

Plastics — Generic identification and marking of
plastics products
1 Scope
1.1   This International Standard specifies a system of uniform marking of products that have been
fabricated from plastics materials. Provision for the process or processes to be used for marking is
outside the scope of this standard.

NOTE Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the
lettering, the appropriate location of the marking, are subject to agreement between the manufacturer and
the user.

1.2    The marking system is intended to help identify plastics products for subsequent decisions
concerning handling, waste recovery or disposal.

1.3    Generic identification of the plastics is provided by the symbols and abbreviated terms given in
ISO 1043, parts 1 to 4.

NOTE If more detailed information for material identification is needed, additional marking of plastics
products can be applied as defined in the appropriate product standard.

1.4    This International Standard is not intended to supplant, replace or in any way interfere with
requirements for labelling found in legislation.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute
provisions of this International Standard. For dated references, subsequent amendments to, or revisions
of, any of these publications do not apply. However, parties to agreements based on this International
Standard are encouraged to investigate the possibility of applying the most recent editions of the
normative documents indicated below. For undated references, the latest edition of the normative
document referred to applies. Members of ISO and IEC maintain registers of currently valid International
Standards.

ISO 472, Plastics
...

NORME ISO
INTERNATIONALE 11469
Troisième édition
2016-10-01
Plastiques — Identification générique
et marquage des produits en matière
plastique
Plastics — Generic identification and marking of plastics products
Numéro de référence
ISO 11469:2016(F)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 11469:2016(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 11469:2016(F)

Sommaire  Page
Avant-propos .iv
1  Domaine d’application . 1
2  Références normatives . 1
3  Termes et définitions . 1
4  Symboles ou termes abrégés . 2
5  Exigences . 2
5.1 Système de marquage . 2
5.1.1 Marquage des produits . 2
5.1.2 Produits mono-constituants . 2
5.1.3 Mélanges de polymères ou alliages . 2
5.1.4 Compositions contenant des additifs spéciaux . 3
5.2 Méthode de marquage . 4
© ISO 2016 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 11469:2016(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation
de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’Organisation
mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC), voir le lien
suivant: www.iso.org/iso/fr/avant-propos.html
Le comité chargé de l’élaboration du présent document est l’ISO/TC 61, Plastiques, sous-comité SC 1,
Terminologie.
Cette troisième édition annule et remplace la deuxième édition (ISO 11469:2000), qui a fait l’objet d’une
révision technique avec les changements suivants:
— la définition de «produits en matière plastique» a été modifiée;
— le marquage des recyclats a été inclus.
iv © ISO 2016 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 11469:2016(F)
Plastiques — Identification générique et marquage des
produits en matière plastique
1  Domaine d’application
La présente Norme internationale prescrit un système de marquage uniforme des produits qui été
fabriqués à partir de matières plastiques. Les dispositions pour le (ou les) procédé(s) de marquage sont
en dehors du domaine d’application de la présente Norme internationale.
NOTE 1 Les caractéristiques précises du marquage, par exemple les dimensions minimales de l’article devant
faire l’objet du marquage, les dimensions du lettrage et l’emplacement approprié auquel apposer le marquage,
font l’objet d’un accord entre le fabricant et l’utilisateur.
Le système de marquage est destiné à faciliter l’identification des produits en matière plastique dans
l’optique de décisions à prendre ultérieurement en ce qui concerne leur manutention, leur valorisation
en tant que déchets ou leur élimination.
L’identification générique des plastiques est constituée par les symboles et les termes abrégés donnés
dans l’ISO 1043-1, l’ISO 1043-2, l’ISO 1043-3 et l’ISO 1043-4.
NOTE 2 Si l’on a besoin d’informations plus détaillées pour l’identification de la matière, on peut appliquer un
marquage complémentaire sur le produit en matière plastique, conformément aux normes de produit pertinentes.
La présente Norme internationale n’a pas pour objectif de supplanter, de remplacer, ou d’interférer,
de quelque manière que ce soit, avec les exigences relatives à l’étiquetage spécifiées dans les normes
produit ou les législations.
2  Références normatives
Les documents suivants, en tout ou partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les ré
...

PROJET DE NORME INTERNATIONALE
ISO/DIS 11469
ISO/TC 61/SC 1 Secrétariat: BSI
Début de vote: Vote clos le:
2015-08-13 2015-11-13
Plastiques — Identification générique et marquage des
produits en matière plastique
Plastics — Generic identification and marking of plastics products
ICS: 83.080.01
TRAITEMENT PARRALLÈLE ISO/CEN
Le présent projet a été élaboré dans le cadre de l’Organisation internationale de
normalisation (ISO) et soumis selon le mode de collaboration sous la direction
de l’ISO, tel que défini dans l’Accord de Vienne.
Le projet est par conséquent soumis en parallèle aux comités membres de l’ISO et
aux comités membres du CEN pour enquête de cinq mois.
En cas d’acceptation de ce projet, un projet final, établi sur la base des observations
CE DOCUMENT EST UN PROJET DIFFUSÉ POUR
OBSERVATIONS ET APPROBATION. IL EST DONC reçues, sera soumis en parallèle à un vote d’approbation de deux mois au sein de
SUSCEPTIBLE DE MODIFICATION ET NE PEUT
l’ISO et à un vote formel au sein du CEN.
ÊTRE CITÉ COMME NORME INTERNATIONALE
AVANT SA PUBLICATION EN TANT QUE TELLE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
Pour accélérer la distribution, le présent document est distribué tel qu’il est
ÉTABLIR S’ILS SONT ACCEPTABLES À DES
FINS INDUSTRIELLES, TECHNOLOGIQUES ET
parvenu du secrétariat du comité. Le travail de rédaction et de composition de
COMMERCIALES, AINSI QUE DU POINT DE VUE
texte sera effectué au Secrétariat central de l’ISO au stade de publication.
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR
POSSIBILITÉ DE DEVENIR DES NORMES
POUVANT SERVIR DE RÉFÉRENCE DANS LA
RÉGLEMENTATION NATIONALE.
Numéro de référence
LES DESTINATAIRES DU PRÉSENT PROJET
ISO/DIS 11469:2015(F)
SONT INVITÉS À PRÉSENTER, AVEC LEURS
OBSERVATIONS, NOTIFICATION DES DROITS
DE PROPRIÉTÉ DONT ILS AURAIENT
ÉVENTUELLEMENT CONNAISSANCE ET À
©
FOURNIR UNE DOCUMENTATION EXPLICATIVE. ISO 2015

---------------------- Page: 1 ----------------------
ISO/DIS 11469:2015(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/DIS 11469:2015
Sommaire Page
Avant-propos. 3
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Symboles ou abréviations . 2
5 Exigences . 2
5.1 Système de marquage . 2
5.1.1 Marquage des produits . 2
5.1.2 Produits mono-constituants . 2
5.1.3 Mélanges de polymères ou alliages . 3
5.1.4 Compositions contenant des additifs spéciaux . 3
5.2 Méthode de marquage . 4

ii Erreur ! Source du renvoi introuvable.

---------------------- Page: 3 ----------------------
ISO/DIS 11469:2015(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le
droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui
concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives
ISO/CEI, Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de
Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des
comités membres votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 11469 a été élaborée par le comité technique ISO/TC 61, Plastiques, sous-comité SC 1,
Terminologie.
Cette troisième édition annule et remplace la deuxième édition de l’ISO 11469:2000, qui a fait l'objet
d'une révision technique.
Erreur ! Source du renvoi introuvable. iii

---------------------- Page: 4 ----------------------
PROJET DE NORME INTERNATIONALE ISO/DIS 11469:2015

Plastiques — Identification générique et marquage des produits
en matière plastique
1 Domaine d’application
1.1 La présente Norme internationale prescrit un système de marquage uniforme des produits en
matière plastique. Les dispositions pour le (ou les) procédé(s) de marquage sont en dehors du domaine
d’application de la présente norme.
NOTE Les caractéristiques précises du marquage, par exemple les dimensions minimales de l'article devant
faire l'objet du marquage, les dimensions du lettrage et l'emplacement approprié auquel apposer le marquage,
font l'objet d'un accord entre le fabricant et l'utilisateur.
1.2 Le système de marquage est destiné à faciliter l'identification des produits en matière plastique
dans l'optique de décisions à prendre ultérieurement en ce qui concerne leur manutention, leur
valorisation en tant que déchets ou leur élimination.
1.3 L'identification générique des plastiques est constituée par les symboles et abréviations donnés
dans l'ISO 1043-1, l’ISO 1043-2, l’ISO 1043-3 et l’ISO 1043-4.
NOTE Si l'on a besoin d'informations plus détaillées pour l'identification de la matière, on peut appliquer un
marquage complémentaire sur le produit en matière plastique, conformément aux normes de produit pertinentes.
1.4 La présente Norme internationale n'a pas po
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.