Abstract

This document specifies the testing of adhesion of coatings on plastics, plastics composites and similar substrates. It also provides an overview of common test methods.

Status
Published
Publication Date
15-Nov-2026
Current Stage
6060 - International Standard published
Start Date
16-Nov-2026
Completion Date
16-Nov-2026

Buy Documents

Standard

ISO 22785-7:2026 - Paints and varnishes — Coatings on plastics and composites — Part 7: Adhesion

Release Date:16-Nov-2026
English language (19 pages)
sale 15% off
Preview
sale 15% off
Preview

ISO 22785-7 is an ISO document on adhesion testing for coatings on plastics, plastics composites and similar substrates. It gives guidance on how to choose and run common adhesion test methods, and it explains how plastics substrates can change the test outcome. The standard is aimed at people who need to specify, prepare, test or judge coated plastic parts in laboratories, quality control and production.

What does ISO 22785-7 specify?

ISO 22785-7 specifies testing of the adhesion of coatings on plastics, plastics composites and similar substrates. It also gives an overview of common test methods so users can match the method to the substrate, the coating system and the purpose of the test.

ISO 22785-7 is organized into clauses 1 to 7, covering scope, normative references, terms and definitions, test specimen characteristics and preparation, the influence of the plastics substrate, test methods, and assessment. The document is not a single test method; it is a guide to several methods that are defined in other standards and then interpreted for plastics and composite substrates.

What are the key requirements of ISO 22785-7?

ISO 22785-7 focuses on specimen preparation, the effect of substrate behavior, and the correct choice and execution of the test method. In practice, the standard helps users avoid misleading adhesion results caused by substrate bending, damage during cutting, or poor visual contrast.

Test specimens and conditioning

Clause 4 says the document applies both to coated test panels and to coated components. The specimen geometry depends on the selected method, and the substrate should be free from flaws or damage that could affect appearance or properties. This matters because defects in the base material can be mistaken for adhesion failure.

Clause 4.2 says conditioning is used to improve repeatability and reproducibility. Plastics generally need longer conditioning than metals because their properties depend strongly on humidity, and the specimen is conditioned unless otherwise specified under standard climatic conditions. For the user, this means conditioning is part of the test setup, not an optional extra.

Substrate effects

Clause 5 explains that plastics and composites behave differently from metallic substrates. Hardness and flexibility can affect stone-chip resistance, and these properties also depend on temperature. The document states that results from flexible plastics and hard plastics are not comparable, so the substrate type must be considered when comparing results.

Clause 5 also warns that cutting tools can damage the substrate, so reduced cutting force may be needed. In practice, this means the test should reveal coating adhesion, not accidental damage to the plastic underneath.

Pull-off test

Clause 6.1 refers to ISO 4624 and describes three pull-off methods: Method A with two dollies, Method B with one dolly for rigid plates only, and Method C with one dolly coated with the material under test. The method is used on rigid and deformable substrates, but flexible plastics need support so the specimen does not deflect during testing. The result is the minimum tensile stress that causes failure at the weakest interface or within the coating.

Floating roller method and cross-cut methods

Clause 6.2 refers to EN 1464 and describes the floating roller peel method. It uses a controlled peel at constant cross-bar advance speed, records peel force over a specified bond length, and reports average, maximum and minimum force. This is useful when peel resistance is the practical question rather than simple pass/fail adhesion.

Clause 6.3 refers to ISO 2409 and describes the cross-cut test as an empirical method, not a pure adhesion measurement. It uses a rectangular grid cut down to the substrate, removes loose particles, and assigns a six-stage rating. The cut spacing depends on coating thickness and whether the substrate is hard or soft. The method is not suitable for total film thickness over 250 µm or for textured coatings.

X-cut tests and T-bend test

Clause 6.4 refers to ISO 16276-2 and describes X-cut test 1 using two cuts at 30° to 45° with visual comparison to reference images. Clause 6.5 describes X-cut test 2, which uses two cuts at 20° to 30° and is preferably used for automotive coatings. Both methods give a visual characteristic value, so the assessor needs reference images or criteria, not just a tool.

Clause 6.6 refers to ISO 17132 and describes the T-bend test, where the specimen is bent around a spacer element or folded around itself. The smallest bend distance with no visible loss of adhesion is determined, or the test can be used as a yes/no check. This is relevant where forming or flexing is part of service use.

Scratch, water jet and impact methods

Clause 6.7 refers to ISO/TR 19402 and describes a scratch test using a knife to remove coating down to the substrate over about 50 mm. The damage pattern is judged in six stages. Clause 6.8 refers to ISO 16925 and describes a pressure water jet test with defined water temperature, angle, distance, flow rate and jetting time, followed by a six-stage visual classification. It is preferably used on automotive coatings.

Clause 6.9 refers to ISO 22557 and describes a hand-applied scratch test using a loaded stylus. The adhesion criterion is no cracking of the coating, so the assessment is a simple visual one. Clauses 6.10, 6.11 and 6.12 cover impact-based methods: the pistol test from ISO 4532, the falling-weight test with large-area indenter from ISO 6272-1, and the falling-weight test with small-area indenter from ISO 6272-2. These methods measure resistance to sudden deformation and report either a characteristic energy level or a yes/no result.

Assessment

Clause 7 states that surfaces are assessed as described in the referenced test standards. It also notes that colour and transparency can make visual judgement harder on plastics, and that contrast can be improved by choosing a high-contrast coating layer or by wetting the specimen with water. This matters because visual rating is central to many of the methods in the document.

What terms does ISO 22785-7 define?

ISO 22785-7 uses terms and definitions from ISO 4618 and ISO 22785-1. The following terms and abbreviations are especially important in practice:

  • Adhesion failure - failure at the interface between coating and substrate, or between coating layers, which is what many of the test methods are looking for.
  • Cohesion failure - failure within the coating itself, which means the coating broke internally rather than losing bond to the substrate.
  • Mixed failures - a combination of adhesion and cohesion failure in the same test result, which can complicate interpretation.
  • GRP - glass-fibre reinforced plastic, named in the cross-cut guidance as an example of a hard substrate.
  • CRP - carbon-fiber-reinforced plastic, also cited as a hard substrate example in the cross-cut guidance.
  • PP - polypropylene, one of the soft-substrate examples given for cross-cut spacing.
  • EPDM - ethylene propylene diene monomer plastic, listed with PP as a soft-substrate example.
  • ABS/PC/PCPBT - acrylonitrile-butadiene-styrene plastic, polycarbonate, and a mixture of polycarbonate and poly(butylene terephthalate), all cited as soft-substrate examples for cross-cut testing.

Who uses ISO 22785-7?

ISO 22785-7 is used by coating laboratories, quality managers, test technicians, specifiers and buyers who need to judge adhesion on plastic parts. It is also relevant to suppliers of paints and varnishes, plastics processors and manufacturers of coated components, especially in automotive applications.

The document is useful when a company must choose between peel, cut, scratch, impact or water-jet methods, or when it needs to explain why a plastic substrate requires different test conditions from metal. It is also a practical reference for anyone writing test specifications or acceptance criteria for coated plastic products.

Which standards are used with ISO 22785-7?

ISO 22785-7 refers to several standards that provide the detailed test methods or shared terminology:

  • ISO 4618 - provides the vocabulary used for paints and varnishes.
  • ISO 22785-1 - provides the general introduction for the ISO 22785 series.
  • ISO 1514 - provides standard panels for testing.
  • ISO 3270 - provides temperatures and humidities for conditioning and testing.
  • ISO 2409 - provides the cross-cut test method.
  • ISO 4624 - provides the pull-off test for adhesion.
  • ISO 16276-2 - provides cross-cut testing and X-cut testing criteria and acceptance guidance.
  • ISO 16925 - provides the pressure water-jetting test method.
  • ISO 17132 - provides the T-bend test method.
  • ISO/TR 19402 - provides guidance on adhesion of coatings and the scratch test.
  • ISO 22557 - provides the scratch test using a spring-loaded pen.
  • ISO 4532 - provides the pistol test.
  • ISO 6272-1 - provides the falling-weight test with large-area indenter.
  • ISO 6272-2 - provides the falling-weight test with small-area indenter.
  • EN 1464 - provides the floating roller peel method.

What does the ISO 22785-7 document contain?

ISO 22785-7 contains a guided overview of adhesion test methods for coatings on plastics and composite substrates, together with the specimen preparation and conditioning considerations that affect those methods. It includes test descriptions for pull-off, peel, cross-cut, X-cut, T-bend, scratch, pressure water jet, pistol impact, and falling-weight impact methods.

The document also contains figures showing the principle or setup of several tests, including cutting tools, peel holders, bending arrangements, scratch tools, water-jet apparatus and impact devices. These visuals help laboratories set up the right geometry and avoid using the wrong fixture or movement.

Several methods are described with visual classification systems, reference images and yes/no outcomes, so the document supports both release testing and comparative evaluation. It also explains how to judge damaged areas on coatings where the plastic substrate can make visual assessment harder than on metal.

Buy Documents

Standard

ISO 22785-7:2026 - Paints and varnishes — Coatings on plastics and composites — Part 7: Adhesion

Release Date:16-Nov-2026
English language (19 pages)
sale 15% off
Preview
sale 15% off
Preview

Get Certified

Connect with accredited certification bodies for this standard

DIN CERTCO

DIN Group product certification.

DAKKS Germany Verified

Smithers Quality Assessments

US management systems and product certification.

ANAB United States Verified

Sponsored listings

Frequently Asked Questions

ISO 22785-7:2026 is a standard published by the International Organization for Standardization (ISO). Its full title is "Paints and varnishes — Coatings on plastics and composites — Part 7: Adhesion". This standard covers: This document specifies the testing of adhesion of coatings on plastics, plastics composites and similar substrates. It also provides an overview of common test methods.

This document specifies the testing of adhesion of coatings on plastics, plastics composites and similar substrates. It also provides an overview of common test methods.

ISO 22785-7:2026 is classified under the following ICS (International Classification for Standards) categories: 83.080.01 - Plastics in general; 83.120 - Reinforced plastics; 87.040 - Paints and varnishes. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 22785-7:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


International
Standard
ISO 22785-7
First edition
Paints and varnishes — Coatings on
2026-11
plastics and composites —
Part 7:
Adhesion
Reference number
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specimen characteristics and preparation . 1
4.1 Requirements for test specimens .1
4.2 Conditioning.1
5 Influence of the plastics substrate on the adhesion test . 2
6 Test methods . 2
6.1 Pull-off test .2
6.2 Floating roller method .3
6.3 Cross-cut test .4
6.4 X-cut test 1 .7
6.5 X-cut test 2 .7
6.6 T-bend test .8
6.7 Scratch test .8
6.8 Pressure water jet test .9
6.9 Scratch test .11
6.10 Pistol test . 12
6.11 Falling-weight test with large-area indenter . 13
6.12 Falling-weight test with small-area indenter .16
7 Assessment . .18
Bibliography . 19

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
A list of all parts in the ISO 22785 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
Introduction
Many of the existing test methods for determining the adhesion of coatings have been developed for metallic
substrates.
This document explains characteristics of plastics and differences between plastics substrates and metallic
substrates, and it shows their potential effect on the behaviour of the coating in different test methods.
It is possible that the substrate has an effect on the behaviour of the coating during the test. It is therefore
sometimes useful to select test conditions that are based, for example, on standards from the plastics sector
and not on standards from the coatings sector, in order to take into account influencing factors such as the
thermal conductivity of the substrate.

v
International Standard ISO 22785-7:2026(en)
Paints and varnishes — Coatings on plastics and
composites —
Part 7:
Adhesion
1 Scope
This document specifies the testing of adhesion of coatings on plastics, plastics composites and similar
substrates.
It also provides an overview of common test methods.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 4618, Paints and varnishes — Vocabulary
ISO 22785-1, Coatings on plastics and composites — Part 1: General introduction
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4618 and ISO 22785-1 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Test specimen characteristics and preparation
4.1 Requirements for test specimens
Both coatings on test specimen panels specified in ISO 1514 and coatings on components are tested.
Depending on the selected test method, there are different requirements for the geometry of the test
specimen.
It is important that the substrates are free from flaws and damage of any kind that could adversely affect
appearance and properties.
The coating system and the substrate are selected together with the pre-treatment and coating methods so
that a homogeneous coating is achieved. The film thickness is documented in accordance with the technical
requirements relating to the visual appearance and/or coating.
4.2 Conditioning
Conditioning serves to improve the repeatability and reproducibility of test results.

As the properties of plastics substrates depend greatly on humidity levels and conditioning usually takes
longer than for metals, a longer conditioning time is usually required for plastics substrates.
The values and times to be selected depend on the test specimen to be tested.
Unless specified otherwise, the test specimens are conditioned for 16 h under standard climatic conditions
specified in ISO 3270.
5 Influence of the plastics substrate on the adhesion test
The chemical and physical properties of plastics and composites as substrates are very different from those
of metallic substrates.
The hardness and flexibility of the substrate can influence the result of testing stone-chip resistance.
The hardness and flexibility of the substrate depend on temperature. For more details, see ISO 22785-1.
Results obtained with flexible plastics substrates and hard plastics substrates are not comparable.
For methods using cutting tools, care shall be taken not to damage the substrate. This can be achieved by
reduced forces when applying cuts.
6 Test methods
6.1 Pull-off test
Three methods for determining adhesion are described in ISO 4624:
— Method A: using two dollies for testing on both rigid and deformable plates;
— Method B: for testing from one side only, using a single dolly (suitable for rigid plates only);
— Method C: using dollies, one of which is coated with the coating material to be tested.
The test can be carried out on numerous substrates. The method differs depending on whether this involves
a deformable substrate, such as thin metal, plastics and wood, or a rigid substrate, such as thick concrete
slabs and metal plates. The sandwich structure is usually used in order to prevent the substrate from
bending during the adhesion test. With flexible plastics, it shall be ensured that the test specimen does not
deflect during the test. To do this, either the test specimen plate is glued onto a firm surface or the test is
carried out with two dollies glued on using the sandwich method. For special purposes, the coating material
may be applied onto a dolly, for example.
Dollies are glued onto the dried/cured coating.
Once the adhesive has cured, the dollies are pulled off with a tensile tester and the force required to pull off
the dolly is measured.
The test result is the minimum tensile stress that shall be applied in order for the weakest interface (adhesion
failure) or the weakest point (cohesion failure) of the test assembly to fail. Adhesion and cohesion failures
can also occur alongside one another (mixed failures).
A schematic representation of the principle of the pull-off test is shown in Figure 1.

Key
1 substrate
2 coating
3 adhesive layer
4 clearance
5 dolly
6 outer ring for supporting the test specimen plate
a
Pull-off direction.
Figure 1 — Principle of the pull-off test
6.2 Floating roller method
The floating roller method is specified in EN 1464.
In accordance with Figure 2, the test specimen is inserted into the retaining device, whereby the non-
glued section of the flexible adherend is clamped into the clamp of the testing machine. Unless otherwise
specified, the test specimens are separated at a constant cross bar advance speed of (100 ± 5) mm/min. If
the rigid adherend bends or warps during the test, the test specimen is designed with a rigid adherend of
sufficient flexural stiffness to ensure uniform peeling. During the peel test, the force counter to the cross-
bar movement (force counter to peeling distance) is recorded over a length of at least 115 mm of the bond
line, whereby the first 25 mm of the peeling distance are disregarded. The results in which a fracture lies
outside of the peeling zone specified in Figure 2 are disregarded.

Dimensions in millimetres
Key
1 rigid adherend
2 peeling zone
3 flexible adherend
4 structural steel
5 double roller bearings
Figure 2 — Holder for mounting the test specimens for the peel test
To make separation easier in the starting area, an adhesive tape or fabric can be inserted during the
production process in order to facilitate layer separation on one side.
The average peeling force in Newtons per millimetre (N/mm) test specimen width that is required to
separate the adherends from one another is determined from the automatically recorded curve for a peeling
distance of at least 115 mm (whereby the first 25 mm and the last 25
...