ISO/TS 5385:2022
(Main)Road vehicles — Anti-fog coating for exterior lighting devices — Specification
Road vehicles — Anti-fog coating for exterior lighting devices — Specification
This document specifies test methods and requirements for anti-fog coating of the exterior lighting devices of road vehicles.
Véhicules routiers — Revêtement antibuée pour dispositifs d'éclairage extérieurs — Spécification
General Information
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 5385
First edition
2022-04
Road vehicles — Anti-fog coating
for exterior lighting devices —
Specification
Véhicules routiers — Revêtement antibuée pour dispositifs d'éclairage
extérieurs — Spécification
Reference number
ISO/TS 5385:2022(E)
© ISO 2022
---------------------- Page: 1 ----------------------
ISO/TS 5385:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 5385:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
4.1 Test condition . 1
4.2 Test specimens. 1
4.3 Examination . 2
5 Specifications . 2
5.1 Coating thickness . 2
5.1.1 Procedure . 2
5.1.2 Requirement . 2
5.2 Adhesion test . 2
5.2.1 Procedure . 2
5.2.2 Evaluation . . 2
5.3 Steam test . 3
5.3.1 Method A . . . 3
5.3.2 Method B . . 4
5.4 Cyclic steam test . 5
5.4.1 Procedure . 5
5.4.2 Evaluation . 5
5.5 High temperature test . . . 5
5.5.1 Procedure . 5
5.5.2 Apparatus . 5
5.5.3 Evaluation . . 5
5.6 Low temperature test . 5
5.6.1 Procedure . 5
5.6.2 Apparatus . 5
5.6.3 Evaluation . . 5
5.7 Condensation water test . 6
5.7.1 Procedure . 6
5.7.2 Evaluation . . 6
5.8 Environmental cycle test . 6
5.8.1 Procedure . 6
5.8.2 Apparatus . 7
5.8.3 Evaluation . 7
5.9 Accelerated weathering . 7
5.9.1 Preparation . 7
5.9.2 Procedure . 8
5.9.3 Evaluation . 8
5.10 Outdoor exposure test . 8
Bibliography . 9
iii
© ISO 2022 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/TS 5385:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO should not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 22 Road Vehicles, Subcommittee SC 35
Lighting and Visibility.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
TECHNICAL SPECIFICATION ISO/TS 5385:2022(E)
Road vehicles — Anti-fog coating for exterior lighting
devices — Specification
1 Scope
This document specifies test methods and requirements for anti-fog coating of the exterior lighting
devices of road vehicles.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 2409, Paints and varnishes — Cross-cut test
ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 13076, Paints and varnishes — Lighting and procedure for visual assessments of coatings
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// w
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.