ISO 22414:2004
(Main)Paper — Cut-size office paper — Measurement of edge quality
Paper — Cut-size office paper — Measurement of edge quality
ISO 22414:2004 specifies a test method for assessing the quality of the cut edge of cut-size office paper. It is applicable to papers of the type described in ISO 216, as well as other cut-size office papers used for printing and copying.
Papier — Format de coupe du papier de bureau — Mesurage de la qualité des bords
General Information
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 22414
First edition
2004-10-15
Paper — Cut-size office paper —
Measurement of edge quality
Papier — Format de coupe du papier de bureau — Mesurage de la
qualité des bords
Reference number
©
ISO 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Principle. 2
5 Apparatus. 2
5.1 Viewing device. 2
5.2 Quality-measurement template. 2
6 Sampling and preparation of test pieces. 2
7 Procedure. 3
8 Expression of results. 3
9 Test report. 3
Annex A (normative) Standard gaps for comparison of the sheet edge . 5
Annex B (informative) Graphic explanation and example according to subclause 7.3 . 6
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 22414 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee SC 2,
Test methods and quality specifications for paper and board.
iv © ISO 2004 – All rights reserved
INTERNATIONAL STANDARD ISO 22414:2004(E)
Paper — Cut-size office paper — Measurement of edge quality
1 Scope
This International Standard specifies a test method for assessing the quality of the cut edge of cut-size office
paper. It is applicable to papers of the type described in ISO 216, as well as other cut-size office papers used
for printing and copying.
The measurement may be made on papers as received, with or without conditioning.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 186, Paper and board — Sampling to determine average quality
ISO 187, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 216, Writing paper and certain classes of printed matter — Trimmed sizes — A and B series
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
edge quality
a measure of the degree of raggedness of cut or slit paper edges
NOTE The degree of raggedness is expressed as a numeric value.
3.2
cut-size office papers
2 2
papers in the range 60 g/m to 150 g/m which are used for writing and/or in various printing and copying
devices
[ISO 14968:1999]
3.3
ream
a pack of 500 identical sheets of paper
NOTE In many countries it is common practice to use the term “ream” for other quantities, for example 480 sheets,
thus affecting the quire. For quantities other than 500 sheets, a different term, such as “pack”, should be used.
[ISO 4046-3:2002].
4 Principle
Estimate
...
INTERNATIONAL ISO
STANDARD 22414
First edition
2004-10-15
Paper — Cut-size office paper —
Measurement of edge quality
Papier — Format de coupe du papier de bureau — Mesurage de la
qualité des bords
Reference number
©
ISO 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Principle. 2
5 Apparatus. 2
5.1 Viewing device. 2
5.2 Quality-measurement template. 2
6 Sampling and preparation of test pieces. 2
7 Procedure. 3
8 Expression of results. 3
9 Test report. 3
Annex A (normative) Standard gaps for comparison of the sheet edge . 5
Annex B (informative) Graphic explanation and example according to subclause 7.3 . 6
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 22414 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee SC 2,
Test methods and quality specifications for paper and board.
iv © ISO 2004 – All rights reserved
INTERNATIONAL STANDARD ISO 22414:2004(E)
Paper — Cut-size office paper — Measurement of edge quality
1 Scope
This International Standard specifies a test method for assessing the quality of the cut edge of cut-size office
paper. It is applicable to papers of the type described in ISO 216, as well as other cut-size office papers used
for printing and copying.
The measurement may be made on papers as received, with or without conditioning.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 186, Paper and board — Sampling to determine average quality
ISO 187, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 216, Writing paper and certain classes of printed matter — Trimmed sizes — A and B series
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
edge quality
a measure of the degree of raggedness of cut or slit paper edges
NOTE The degree of raggedness is expressed as a numeric value.
3.2
cut-size office papers
2 2
papers in the range 60 g/m to 150 g/m which are used for writing and/or in various printing and copying
devices
[ISO 14968:1999]
3.3
ream
a pack of 500 identical sheets of paper
NOTE In many countries it is common practice to use the term “ream” for other quantities, for example 480 sheets,
thus affecting the quire. For quantities other than 500 sheets, a different term, such as “pack”, should be used.
[ISO 4046-3:2002].
4 Principle
Estimate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.