oSIST prEN 1705:2024

Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow

This document specifies a test method for determining the leaktightness and the ease of operation of a valve made of thermoplastic material following an impact applied to the operating device.
Additionally, a different procedure of the test on diaphragm valve can be specified by the valve manufacturer.

Kunststoff-Rohrleitungssysteme - Thermoplast-Armaturen - Prüfverfahren der Unversehrtheit einer Armatur nach äußerer Schlagbelastung

Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Dichtheit und der Leichtgängigkeit einer Armatur aus thermoplastischem Werkstoff nach einem Schlag auf die Betätigungsvorrichtung fest.
Der Hersteller der Armatur kann zusätzlich ein anderes Verfahren zur Prüfung des Membranventils festlegen.

Systèmes de canalisations en plastique - Robinets en thermoplastiques - Méthode d'essai pour la vérification d'un robinet après un choc externe

Le présent document spécifie une méthode d’essai pour déterminer l’étanchéité et la facilité de manoeuvre d’un robinet fabriqué en matière thermoplastique à la suite d’un choc appliqué au dispositif de manoeuvre.
En outre, un mode opératoire différent de l'essai sur un robinet à membrane peut être spécifié par le fabricant de robinet.

Cevni sistemi iz polimernih materialov - Plastomerni ventili - Metoda za preskus neoporečnosti ventila po zunanjem udarcu

General Information

• Status: Not Published
• Public Enquiry End Date: 29-May-2024
• ICS: 23.060.01 - Valves in general
• ICS: 83.140.40 - Hoses
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 09-Apr-2024
• Due Date: 27-Aug-2024
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Ref Project: prEN 1705 - Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow

Relations

• Revises: SIST EN 1705:1997 - Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
• Effective Date: 11-Oct-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 1705:2024
01-maj-2024
Cevni sistemi iz polimernih materialov - Plastomerni ventili - Metoda za preskus
neoporečnosti ventila po zunanjem udarcu
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve
after an external blow
Kunststoff-Rohrleitungssysteme - Thermoplast-Armaturen - Prüfverfahren der
Unversehrtheit einer Armatur nach äußerer Schlagbelastung
Systèmes de canalisations en plastique - Robinets en thermoplastiques - Méthode
d'essai pour la vérification d'un robinet après un choc externe
Ta slovenski standard je istoveten z: prEN 1705
ICS:
23.060.01 Ventili na splošno Valves in general
83.140.40 Gumene cevi Hoses
oSIST prEN 1705:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1705:2024

---------------------- Page: 2 ----------------------
oSIST prEN 1705:2024


DRAFT
EUROPEAN STANDARD
prEN 1705
NORME EUROPÉENNE

EUROPÄISCHE NORM

March 2024
ICS 23.060.01 Will supersede EN 1705:1996
English Version

Plastics piping systems - Thermoplastics valves - Test
method for the integrity of a valve after an external blow
Systèmes de canalisations en plastique - Robinets en Kunststoff-Rohrleitungs system - Thermoplast-
thermoplastiques - Méthode d'essai pour la vérification Armaturen - Prüfverfahren der Unversehrtheit einer
d'un robinet après un choc externe Armatur nach äußerer Schlagbelastung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1705:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1705:2024
prEN 1705:2024 (E)
Contents Page
EUROPEAN FOREWORD . 3
1 SCOPE . 4
2 NORMATIVE REFERENCES . 4
3 TERMS AND DEFINITIONS . 4
4 PRINCIPLE . 5
5 APPARATUS . 7
6 TEST PIECE . 8
6.1 SAMPLING . 8
6.2 PREPAR
...