SIST EN ISO 14373:2024
(Main)Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2024)
Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2024)
This document specifies requirements for resistance spot welding in the fabrication of assemblies ofuncoated, and metallic coated or weldable non-metallic coated low carbon steel, comprising two orthree sheets of metal, where the maximum single sheet thickness of components to be welded is withinthe range 0,4 mm to 3 mm.
This document is applicable to welding of sheets of the same or dissimilar thickness, where the thickness ratio is less than or equal to 3:1. It applies to the welding of three thicknesses, where the total thickness is less than or equal to 9 mm. Welding with the following types of equipment is within the scope of this document:
a) pedestal welding equipment;
b) welding guns;
c) automatic welding equipment where the components are fed by robots or automatic feeding equipment;
d) multi welders;
e) robotic welders.
Information on appropriate welding equipment is given in Annex A, and information on spot welding conditions is given in Annex B. This information is provided for guidance only.Depending on the service conditions of the fabrication, the type of welding equipment, the characteristics of the secondary circuit, the electrode material, and the shape, it is possible that certain modifications are necessary. In such cases, further information can be obtained from the relevant application standard, where one exists.
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen mit oder ohne metallischem Überzug (ISO 14373:2024)
Dieses Dokument legt Anforderungen an das Widerstandspunktschweißen bei der Fertigung von Bauteilen aus niedriglegiertem Stahl ohne Überzug und mit metallischem Überzug oder schweißbarem nichtmetallischen Überzug fest, die aus zwei oder drei Metallblechen bestehen, wobei die größte Dicke eines Einzelbleches der zu schweißenden Bauteile im Bereich von 0,4 mm bis 3 mm liegt.
Dieses Dokument ist anwendbar für das Schweißen von Blechen gleicher oder ungleicher Dicke mit einem Dickenverhältnis von nicht mehr als 3 : 1.
Die folgenden Arten von Schweißeinrichtungen liegen im Anwendungsbereich dieses Dokumentes:
a) Ständerschweißmaschinen;
b) tragbare Schweißzangen;
c) automatische Schweißeinrichtungen, bei denen die Bauteile durch Roboter oder automatische Zuführungen zugeführt werden;
d) Vielpunkt-Schweißmaschinen;
e) Roboter-Schweißmaschinen.
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et non revêtus (ISO 14373:2024)
Le présent document spécifie les exigences relatives au soudage par résistance par points pour la fabrication d'assemblages en acier à bas carbone non revêtu et à revêtement métallique ou à revêtement non métallique soudable, avec deux ou trois épaisseurs de métal, l'épaisseur maximale de chaque tôle constituant les pièces à souder étant comprise entre 0,4 mm et 3,0 mm.
Le présent document s'applique au soudage de tôles présentant une épaisseur similaire ou inégale, et dont le rapport entre les épaisseurs est inférieur ou égal à 3:1.
Le présent document couvre le soudage réalisé avec les types de matériels suivants:
a) machine de soudage avec commande au pied;
b) pinces de soudage portables;
c) matériel de soudage automatique avec lequel les composants sont mis en place par des robots ou des appareils d'alimentation automatique;
d) machines à souder multi-points;
e) robots de soudage.
Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih maloogljičnih jekel (ISO 14373:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14373:2024
01-junij-2024
Nadomešča:
SIST EN ISO 14373:2015
Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih
maloogljičnih jekel (ISO 14373:2024)
Resistance welding - Procedure for spot welding of uncoated and coated low carbon
steels (ISO 14373:2024)
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen
mit oder ohne metallischem Überzug (ISO 14373:2024)
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas
carbone revêtus et non revêtus (ISO 14373:2024)
Ta slovenski standard je istoveten z: EN ISO 14373:2024
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 14373:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14373:2024
---------------------- Page: 2 ----------------------
SIST EN ISO 14373:2024
EN ISO 14373
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2024
EUROPÄISCHE NORM
ICS 25.160.10 Supersedes EN ISO 14373:2015
English Version
Resistance welding - Procedure for spot welding of
uncoated and coated low carbon steels (ISO 14373:2024)
Soudage par résistance - Mode opératoire pour le Widerstandsschweißen - Verfahren zum
soudage par points des aciers à bas carbone revêtus et Punktschweißen von niedriglegierten Stählen mit oder
non revêtus (ISO 14373:2024) ohne metallischem Überzug (ISO 14373:2024)
This European Standard was approved by CEN on 29 December 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14373:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14373:2024
EN ISO 14373:2024 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14373:2024
EN ISO 14373:2024 (E)
European foreword
This document (EN ISO 14373:2024) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2024, and conflicting national standards shall be
withdrawn at the latest by July 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14373:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 14373:2024 has been approved by CEN as EN ISO 14373:2024 without any modifica
...
SLOVENSKI STANDARD
oSIST prEN ISO 14373:2023
01-maj-2023
Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih
maloogljičnih jekel (ISO/DIS 14373:2023)
Resistance welding - Procedure for spot welding of uncoated and coated low carbon
steels (ISO/DIS 14373:2023)
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen
mit oder ohne metallischem Überzug (ISO/DIS 14373:2023)
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas
carbone revêtus et non revêtus (ISO/DIS 14373:2023)
Ta slovenski standard je istoveten z: prEN ISO 14373
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
oSIST prEN ISO 14373:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 14373:2023
---------------------- Page: 2 ----------------------
oSIST prEN ISO 14373:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14373
ISO/TC 44/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-03-16 2023-06-08
Resistance welding — Procedure for spot welding of
uncoated and coated low carbon steels
Soudage par résistance — Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et
non revêtus
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14373:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
oSIST prEN ISO 14373:2023
ISO/DIS 14373:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14373
ISO/TC 44/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
Resistance welding — Procedure for spot welding of
uncoated and coated low carbon steels
Soudage par résistance — Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et
non revêtus
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 14373:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 4 ----------------------
oSIST prEN ISO 14373:2023
ISO/DIS 14373:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.