SIST EN ISO 17672:2024
(Main)Brazing - Filler metals (ISO 17672:2024)
Brazing - Filler metals (ISO 17672:2024)
ISO 17672:2016 specifies the compositional ranges of a series of filler metals used for brazing. The filler metals are divided into seven classes, related to their composition, but not necessarily to the major element present.
Hartlöten - Lote (ISO 17672:2024)
Dieses Dokument legt die Zusammensetzungen von Loten fest, die zum Hartlöten verwendet werden. Diese Lote sind entsprechend ihrer Zusammensetzung, aber nicht notwendigerweise nach dem vorhandenen Hauptlegierungselement, in sieben Gruppen aufgeteilt.
ANMERKUNG 1 Für die Hauptlegierungselemente, siehe Anhang A.
Im Falle von Verbundwerkstoffen, wie z. B. flussmittelummantelte Lotstäbe, Lotpasten oder -bänder, ist dieses Dokument nur für den Lotanteil solcher Produkte anwendbar. Die in den Tabellen angegebenen Schmelztemperaturen sind nur Näherungswerte, da sie entsprechend der erlaubten Bandbreite der Zusammensetzung der Lote zwangsläufig variieren. Deshalb dienen diese Angaben nur zur Information. Die technischen Lieferbedingungen gelten für Lote zum Hartlöten und für Produkte, die Hartlote mit anderen Bestandteilen wie Flussmittel und/oder Umhüllung enthalten.
ANMERKUNG 2 Für einige Anwendungen, z. B. Schmuckverarbeitung, Luft- und Raumfahrt und Zahntechnik, werden oft andere Lote als die, die in diesem Dokument enthalten sind, verwendet. Diese Lote sind in anderen Internationalen Normen enthalten, auf die Bezug genommen werden kann.
Brasage fort - Métaux d'apport (ISO 17672:2024)
ISO 17672:2016 spécifie les gammes de composition d'une série de métaux d'apport utilisés pour le brasage fort. Les métaux d'apport sont divisés en sept classes, d'après leur composition, mais pas nécessairement d'après leur élément majeur présent.
Trdo spajkanje - Dodajni materiali (ISO 17672:2024)
Standard ISO 17672:2016 določa sestavne obsege nabora dodajnih materialov, ki se uporabljajo za trdo spajkanje. Dodajni materiali so razdeljeni v sedem razredov glede na sestavo, vendar ne nujno glede na prisotni glavni element.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN ISO 17672:2016
Trdo spajkanje - Dodajni materiali (ISO 17672:2024)
Brazing - Filler metals (ISO 17672:2024)
Hartlöten - Lote (ISO 17672:2024)
Brasage fort - Métaux d'apport (ISO 17672:2024)
Ta slovenski standard je istoveten z: EN ISO 17672:2024
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 17672
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 25.160.50 Supersedes EN ISO 17672:2016
English Version
Brazing - Filler metals (ISO 17672:2024)
Brasage fort - Métaux d'apport (ISO 17672:2024) Hartlöten - Lote (ISO 17672:2024)
This European Standard was approved by CEN on 7 July 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17672:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 17672:2024) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards
shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17672:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 17672:2024 has been approved by CEN as EN ISO 17672:2024 without any modification.
International
Standard
ISO 17672
Third edition
Brazing — Filler metals
2024-04
Brasage fort — Métaux d'apport
Reference number
ISO 17672:2024(en) © ISO 2024
ISO 17672:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 17672:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Composition . 1
5 Special vacuum requirement . 2
6 Chemical analysis . . 2
7 Designation . 3
8 Technical delivery conditions . 3
8.1 Types of product .3
8.2 Dimensions .3
8.2.1 General .3
8.2.2 Foils .3
8.2.3 Rods .4
8.2.4 Wires .4
8.3 Condition .5
8.4 Marking .5
8.5 Packaging .5
8.6 Product certificates .5
9 Health and safety precautions . 5
Annex A (informative) Codification . 16
Bibliography .21
iii
ISO 17672:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 13, Brazing materials and processes, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 121, Welding and allied processes, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 17672:2016), which has been technically
revised.
The main changes are as follows:
— in Clause 6, the spatter test was added;
— in 8.2.2, a NOTE on foils with a width of less than 3 mm was added;
— in Table 6, four new silver brazing filler metals were added;
— in Table 7, the range of Si was changed to 0,01 up to 0,25 (mass fraction %) if intentionally added;
— in Table 11, two new Ni-Cr-P-Si alloys were added;
— in Table A.1, the codes were updated and corresponding GB codes were added.
Any feedback or questions on this document should be directed to the user’s
national standards body. A complete listing of these bodies can be found at
www.iso.org/members.html. Official interpretations of ISO/TC 44 documents, where they exist, are
available from this page: https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
International Standard ISO 17672:2024(en)
Brazing — Filler metals
1 Scope
This document specifies the compositional ranges of a series of filler metals used for brazing. The filler
metals are divided into seven classes, related to their composition but not necessarily to the major element
present.
NOTE 1 For the major element(s) present, see Annex A.
In the case of composite products, such as flux-coated rods, pastes or plastics tapes, this document covers
only the filler metal that forms parts of such products. The melting temperatures given in the tables are only
approximate, as they necessarily vary within the compositional range of the filler metal. Therefore, they are
given only for information. Technical delivery conditions are given for brazing
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.