Aerospace series - Quality management systems - Variation management of key characteristics

1.1   General
This document is primarily intended to apply to new parts and products intended to be produced in an on-going production phase but can also be applied to parts currently in production (e.g., manufacturing, maintenance). This document is applicable to all production processes that influence the variation of KCs, as well as maintenance and service processes in which KCs are identified. It applies to organizations for assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product.
The variation control process begins with product definition, typically stated in the design documentation (e.g., digital model, engineering drawing, specification) which identifies KCs, and leads to a variation management process for those KCs. This process may also be used for producer-identified KCs (e.g., process KCs, additional/substitute product KCs).
Producers and their subcontractors are responsible for flow down of the standard requirements to those external providers, who produce design characteristics and provide production and service provisions, to ensure that KCs conform to the customer’s requirements.
1.2   Purpose
This document is designed to drive the improvement of manufacturing and maintenance processes through adequate planning and effective management of KC variation. This focus is intended to improve uniformity (less variation or minimum variation of product KCs) and acceptance probability of the end-product.
NOTE   Control of a product or process KC per this document does not constitute, nor imply acceptance of the resulting product. If variation management, under this document, is to be part of an acceptance decision, the requirements need to be specified in the applicable product acceptance plan or contract.
1.3   Convention
The following conventions are used in this document:
-   "shall" indicates a requirement;
-   "should" indicates a recommendation;
-   "may" indicates a permission;
-   "can" indicates a possibility or a capability.

Luft- und Raumfahrt - Qualitätsmanagementsystems - Management der Veränderung der Haupteigenschaften

Série aérospatiale - Systèmes de management de la qualité - Management de la variation des caractéristiques clefs

Aeronavtika - Sistemi vodenja kakovosti - Vodenje sprememb ključnih značilnosti

1.1   Splošno
Ta dokument je namenjen zlasti uporabi za nove dele in izdelke, ki so predvideni za trajno proizvodnjo, vendar ga je mogoče uporabiti tudi za dele, ki se trenutno proizvajajo (npr. proizvodnja, vzdrževanje). Ta dokument se uporablja za vse proizvodne postopke, ki vplivajo na spremembe ključnih značilnosti (KC), ter za vzdrževalne in servisne postopke, v katerih so opredeljene ključne značilnosti. Uporablja se za organizacije, ki izdelujejo sestave in vse ravni delov v sestavu, vse do osnovnih materialov, vključno z odlitki in izkovki, ter za organizacije, ki so odgovorne za proizvodnjo značilnosti zasnove izdelka.
Proces nadziranja sprememb se začne z definicijo izdelka, ki je običajno navedena v projektni dokumentaciji (npr. digitalni model, tehnična risba ali specifikacija), ki opredeljuje ključne značilnosti, in vodi v postopek vodenja sprememb za zadevne ključne značilnosti. Ta proces se lahko uporabi tudi za ključne značilnosti, ki jih opredeli proizvajalec (npr. ključne značilnosti procesov ali dodatnih/nadomestnih izdelkov).
Proizvajalci in njihovi podizvajalci so odgovorni za posredovanje standardnih zahtev zunanjim ponudnikom, ki proizvajajo značilnosti zasnove ter so odgovorni za proizvodnjo in izvedbo storitev, s čimer zagotovijo, da so ključne značilnosti v skladu z zahtevami strank.
1.2   Namen
Ta dokument je namenjen izboljšanju proizvodnje in proizvodnih postopkov z ustreznim načrtovanjem in učinkovitim vodenjem sprememb ključnih značilnosti. Poudarek je na večji enotnosti (manj sprememb ali minimalne spremembe ključnih značilnosti izdelkov) in verjetnosti sprejemljivosti končnega izdelka.
OPOMBA:   Nadzor ključne značilnosti izdelka ali procesa v skladu s tem dokumentom ne pomeni ali nakazuje sprejemljivosti nastalega izdelka. Če naj bi bilo vodenje sprememb v skladu s tem dokumentom del odločitve o sprejemljivosti, je treba zahteve v zvezi s tem določiti v ustreznem načrtu ali pogodbi o sprejemljivosti izdelka.
1.3   Konvencija
V tem dokumentu so uporabljene naslednje konvencije:
– »treba je« ali »mora« označuje zahtevo;
– »naj« označuje priporočilo;
– »sme« označuje dovoljenje;
– »lahko« označuje možnost ali sposobnost.

General Information

Status
Published
Public Enquiry End Date
20-Dec-2022
Publication Date
03-Dec-2023
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Nov-2023
Due Date
02-Feb-2024
Completion Date
04-Dec-2023

Relations

Buy Standard

Standard
EN 9103:2024 - BARVE
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 9103:2022 - BARVE
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 9103:2024
01-januar-2024
Aeronavtika - Sistemi vodenja kakovosti - Vodenje sprememb ključnih značilnosti
Aerospace series - Quality management systems - Variation management of key
characteristics
Luft- und Raumfahrt - Qualitätsmanagementsystems - Management der Veränderung
der Haupteigenschaften
Série aérospatiale - Systèmes de management de la qualité - Management de la
variation des caractéristiques clefs
Ta slovenski standard je istoveten z: EN 9103:2023
ICS:
03.100.70 Sistemi vodenja Management systems
03.120.10 Vodenje in zagotavljanje Quality management and
kakovosti quality assurance
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
SIST EN 9103:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 9103:2024

---------------------- Page: 2 ----------------------
SIST EN 9103:2024


EN 9103
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2023
EUROPÄISCHE NORM
ICS 03.100.70; 03.120.10; 49.020 Supersedes EN 9103:2014
English Version

Aerospace series - Quality management systems -
Variation management of key characteristics
Série aérospatiale - Systèmes de management de la Luft- und Raumfahrt - Qualitätsmanagementsystems -
qualité - Gestion des variations des caractéristiques Management der Veränderung der Haupteigenschaften
clés
This European Standard was approved by CEN on 7 August 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 9103:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 9103:2024
EN 9103:2023 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 8
1.1 General. 8
1.2 Purpose . 8
1.3 Convention . 8
2 Normative references . 9
3 Terms and definitions . 10
4 General requirements . 13
4.1 Flow down of product key characteristics . 13
4.2 Preparation of control plan inputs and outputs . 14
4.3 Conditions for performing statistical process control . 15
4.4 A
...

SLOVENSKI STANDARD
oSIST prEN 9103:2022
01-december-2022
Aeronavtika - Sistemi vodenja kakovosti - Vodenje sprememb ključnih značilnosti
Aerospace series - Quality management systems - Variation management of key
characteristics
Luft- und Raumfahrt - Qualitätsmanagementsysteme - Management der Veränderung
der Haupteigenschaften
Série aérospatiale - Systèmes de management de la qualité - Management de la
variation des caractéristiques clés
Ta slovenski standard je istoveten z: prEN 9103
ICS:
03.100.70 Sistemi vodenja Management systems
03.120.10 Vodenje in zagotavljanje Quality management and
kakovosti quality assurance
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
oSIST prEN 9103:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 9103:2022

---------------------- Page: 2 ----------------------
oSIST prEN 9103:2022


DRAFT
EUROPEAN STANDARD
prEN 9103
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2022
ICS 03.100.70; 03.120.10; 49.020 Will supersede EN 9103:2014
English Version

Aerospace series - Quality management systems -
Variation management of key characteristics
Série aérospatiale - Systèmes de management de la Luft- und Raumfahrt - Qualitätsmanagementsysteme -
qualité - Management de la variation des Management der Veränderung der Haupteigenschaften
caractéristiques clés
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 9103:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 9103:2022
prEN 9103:2022 (E)
Contents Page
European foreword . 4
Rationale . 5
Introduction . 6
1 Scope . 9
1.1 General. 9
1.2 Purpose . 9
1.3 Convention . 9
2 Normative references . 9
3 Terms and definitions . 10
4 General requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.