SIST EN 60384-3:2016
(Main)Fixed capacitors for use in electronic equipment - Part 3: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte (IEC 60384-3:2016)
Fixed capacitors for use in electronic equipment - Part 3: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte (IEC 60384-3:2016)
IEC 60384-3:2006 applies to surface mount tantalum solid electrolyte capacitors. These capacitors are primarily intended to be mounted directly onto substrates for hybrid circuits or onto printed boards. The following two styles are considered: Style 1 - protected capacitors; Style 2 - unprotected capacitors. This third edition cancels and replaces the second edition published in 1989 and constitutes a minor revision related to tables, figures and references This bilingual version, published in 2008-06, corresponds to the English version.
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 3: Rahmenspezifikation: Oberflächenmontierbare Tantal-Kondensatoren mit festem Mangandioxid-Elektrolyt
Condensateurs fixes utilisés dans les équipements électroniques - Partie 3: Spécification intermédiaire: Condensateurs fixes électrolytiques au tantale pour montage en surface, à électrolyte solide au dioxyde de manganèse
La CEI 60384-3:2006 s'applique aux condensateurs au tantale pour montage en surface, à électrolyte solide. Ces condensateurs sont principalement destinés à être montés directement sur des substrats pour circuits hybrides ou sur des cartes imprimées. On considère les 2 modèles suivants: Modèle 1 - condensateurs protégés; Modèle 2 - condensateurs non protégés. Cette troisième édition annule et remplace la deuxième édition publiée en 1989. Elle constitue une révision mineure des tableaux, valeurs et références. La présente version bilingue correspond à la version anglaise.
Nespremenljivi kondenzatorji za elektronsko opremo - 3. del: Področna specifikacija: Nespremenljivi tantalovi elektrolitski kondenzatorji s trdnim elektrolitom iz manganovega dioksida za površinsko montažo (IEC 60384-3:2016)
Standard IEC 60384-3:2006 se uporablja za tantalove elektrolitske kondenzatorje s trdnim elektrolitom za površinsko montažo. Ti kondenzatorji so namenjeni namestitvi neposredno na podloge za hibridne tokokroge ali na tiskana vezja. Obravnavani sta naslednji dve vrsti kondenzatorjev: vrsta 1 – zaščiteni kondenzatorji; vrsta 2 – nezaščiteni kondenzatorji. Ta tretja izdaja preklicuje in zamenjuje drugo izdajo, objavljeno leta 1989, ter vsebuje majhne popravke razpredelnic, slik in sklicev. Ta dvojezična različica, objavljena junija 2008, ustreza angleški različici.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RþQDFestkondensatoren zur Verwendung in Geräten der Elektronik - Teil 3: Rahmenspezifikation: Oberflächenmontierbare Tantal-Kondensatoren mit festem Mangandioxid-ElektrolytCondensateurs fixes utilisés dans les équipements électroniques - Partie 3: Spécification intermédiaire: Condensateurs fixes électrolytiques au tantale pour montage en surface, à électrolyte solide au dioxyde de manganèseFixed capacitors for use in electronic equipment - Part 3: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte (IEC 60384-3:2016)31.060.40Tantalski elektrolitni kondenzatorjiTantalum electrolytic capacitorsICS:Ta slovenski standard je istoveten z:EN 60384-3:2016SIST EN 60384-3:2016en01-december-2016SIST EN 60384-3:2016SLOVENSKI
STANDARDSIST EN 60384-3:20081DGRPHãþD
SIST EN 60384-3:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60384-3
October 2016 ICS 31.060.30
Supersedes
EN 60384-3:2006
English Version
Fixed capacitors for use in electronic equipment -
Part 3: Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electrolyte (IEC 60384-3:2016)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 3: Spécification intermédiaire - Condensateurs fixes électrolytiques au tantale pour montage en surface, à électrolyte solide (MnO2) (IEC 60384-3:2016)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 3: Rahmenspezifikation - Oberflächenmontierbare Tantal-Kondensatoren mit festem (MnO2)-Elektrolyt (IEC 60384-3:2016) This European Standard was approved by CENELEC on 2016-08-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60384-3:2016 E SIST EN 60384-3:2016
EN 60384-3:2016 2 European foreword The text of document 40/2464/FDIS, future edition 4 of IEC 60384-3, prepared by IEC/TC 40 "Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60384-3:2016. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-05-16 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-08-16
This document supersedes EN 60384-3:2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60384-3:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated : IEC 60068-2-58:2015 NOTE Harmonized as EN 60068-2-58:2015 (not modified). SIST EN 60384-3:2016
EN 60384-3:2016 3 Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60062 -
Marking codes for resistors and capacitors EN 60062 -
IEC 60063 -
Preferred number series for resistors and capacitors EN 60063 -
IEC 60068-1 2013
Environmental testing - Part 1: General and guidance EN 60068-1 2014
IEC 60384-1 2016
Fixed capacitors for use in electronic equipment -
Part 1: Generic specification EN 60384-1 2016
IEC 60417 -
Graphical symbols for use on equipment - -
IEC 61193-2 2007
Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 2007
ISO 3 -
Preferred numbers - Series of preferred numbers - -
SIST EN 60384-3:2016
SIST EN 60384-3:2016
IEC 60384-3 Edition 4.0 2016-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed capacitors for use in electronic equipment –
Part 3: Sectional specification – Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electrolyte
Condensateurs fixes utilisés dans les équipements électroniques –
Partie 3: Spécification intermédiaire – Condensateurs fixes électrolytiques
au tantale pour montage en surface, à électrolyte solide (MnO2)
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 31.060.30
ISBN 978-2-8322-3508-9
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60384-3:2016
– 2 – IEC 60384-3:2016 © IEC 2016 CONTENTS FOREWORD . 5 1 General . 7 1.1 Scope . 7 1.2 Object . 7 1.3 Normative references . 7 1.4 Information to be given in a detail specification . 8 1.4.1 General . 8 1.4.2 Outline drawing and dimensions . 8 1.4.3 Mounting . 8 1.4.4 Ratings and characteristics . 8 1.4.5 Marking . 9 1.5 Terms and definitions . 9 1.6 Marking . 9 1.6.1 General . 9 1.6.2 Information for marking . 9 1.6.3 Marking on capacitors . 9 1.6.4 Marking on packaging . 10 2 Preferred ratings and characteristics . 10 2.1 Preferred characteristics . 10 2.2 Preferred values of ratings . 10 2.2.1 Nominal capacitance (CN) . 10 2.2.2 Tolerance on nominal capacitance . 11 2.2.3 Rated voltage (UR) . 11 2.2.4 Category voltage (UC) . 11 2.2.5 Surge voltage (URS or UCS) . 11 2.2.6 Rated temperature . 11 3 Quality assessment procedures . 12 3.1 Primary stage of manufacture . 12 3.2 Structurally similar components . 12 3.3 Certified test records of released lots . 12 3.4 Qualification approval procedures . 12 3.4.1 General . 12 3.4.2 Qualification approval on the basis of the fixed sample size procedure . 12 3.4.3 Tests . 13 3.5 Quality conformance inspection . 20 3.5.1 Formation of inspection lots . 20 3.5.2 Test schedule . 20 3.5.3 Delayed delivery . 20 3.5.4 Assessment levels . 20 4 Test and measurement procedures . 21 4.1 Drying . 22 4.2 Measuring conditions . 22 4.3 Mounting . 22 4.3.1 General . 22 4.3.2 Initial inspection . 22 4.3.3 Final inspections . 22 SIST EN 60384-3:2016
IEC 60384-3:2016 © IEC 2016 – 3 – 4.4 Visual examination and check of dimensions . 22 4.4.1 General . 22 4.4.2 Visual examination and check of dimensions . 22 4.4.3 Requirements . 22 4.5 Electrical tests . 22 4.5.1 Leakage current . 22 4.5.2 Capacitance . 23 4.5.3 Tangent of loss angle (tan δ) . 23 4.5.4 Impedance (if required) . 23 4.5.5 Equivalent series resistance (ESR) (if required) . 24 4.6 Resistance to soldering heat . 24 4.6.1 General . 24 4.6.2 Test conditions . 24 4.6.3 Recovery . 24 4.6.4 Final inspections and requirements . 25 4.7 Solderability . 25 4.7.1 General . 25 4.7.2 Test conditions . 25 4.7.3 Final inspections and requirements . 25 4.8 Shear test . 25 4.8.1 General . 25 4.8.2 Final inspections and requirements . 25 4.9 Substrate bending test . 25 4.9.1 General . 25 4.9.2 Final inspections and requirements . 25 4.10 Rapid change of temperature . 25 4.10.1 General . 25 4.10.2 Initial inspection . 25 4.10.3 Test conditions . 25 4.10.4 Recovery . 26 4.10.5 Final inspections and requirements . 26 4.11 Climatic sequence (if required) . 26 4.11.1 General . 26 4.11.2 Initial inspections . 26 4.11.3 Dry heat . 26 4.11.4 Damp heat, cyclic, test Db, first cycle . 26 4.11.5 Cold . 26 4.11.6 Damp heat, cyclic, test Db, remaining cycles . 26 4.11.7 Recovery . 26 4.11.8 Final inspections and requirements . 26 4.12 Damp heat, steady state (if required) . 26 4.12.1 General . 26 4.12.2 Initial inspections . 27 4.12.3 Test conditions . 27 4.12.4 Recovery . 27 4.12.5 Final inspections and requirements . 27 4.13 Characteristics at high and low temperature . 27 4.13.1 General . 27 4.13.2 Inspections and requirements . 27 SIST EN 60384-3:2016
– 4 – IEC 60384-3:2016 © IEC 2016 4.14 Surge voltage . 27 4.14.1 General . 27 4.14.2 Initial inspections . 27 4.14.3 Test conditions . 27 4.14.4 Recovery . 28 4.14.5 Final inspections and requirements . 28 4.15 Endurance . 28 4.15.1 General . 28 4.15.2 Initial inspections . 28 4.15.3 Test conditions . 28 4.15.4 Recovery . 28 4.15.5 Final inspections and requirements . 29 4.16 Reverse voltage (if required) . 29 4.16.1 Initial inspections . 29 4.16.2 Test conditions . 29 4.16.3 Recovery . 29 4.16.4 Final inspections and requirements . 29 4.17 Component solvent resistance (if required) . 29 4.18 Solvent resistance of the marking (if required) . 29 4.19 High surge current (if required) . 29 Bibliography . 30
Table 1 – Letter code and digit . 10 Table 2 – Category voltages and surge voltages . 11 Table 3 – Sampling plan for qualification approval, assessment level EZ . 14 Table 4 – Test schedule for qualification approval . 15 Table 5 – Lot-by-lot inspection . 21 Table 6 – Periodic inspection . 21 Table 7 – Test temperatures . 28
SIST EN 60384-3:2016
IEC 60384-3:2016 © IEC 2016 – 5 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 3: Sectional specification – Surface mount fixed tantalum
electrolytic capacitors with solid (MnO2) electrolyte
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-3 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This fourth edition cancels and replaces the third edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Revision of the structure in accordance with ISO/IEC Directives, Part 2:2011 (sixth edition) to the extent practicable, and harmonization between other similar kinds of documents.
b) In addition, Clause 4 and all the tables have been reviewed in order to prevent duplications and contradictions. The text of this standard is based on the following documents: SIST EN 60384-3:2016
– 6 – IEC 60384-3:2016 © IEC 2016 FDIS Report on voting 40/2464/FDIS 40/2470/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all the parts of the IEC 60384 series, under the general title Fixed capacitors for use in electronic equipment, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
SIST EN 60384-3:2016
IEC 60384-3:2016 © IEC 2016 – 7 – FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 3: Sectional specification – Surface mount fixed tantalum
electrolytic capacitors with solid (MnO2) electrolyte
1 General 1.1 Scope This part of IEC 60384 applies to fixed tantalum electrolytic surface mount capacitors with solid (MnO2) electrolyte primarily intended for d.c. applications for use in electronic equipment. These capacitors are primarily intended for use in electronic equipment to be mounted directly on substrates for hybrid circuits or to printed boards. Capacitors for special-purpose applications may need additional requirements. The following two styles are considered: – Style 1: Capacitors protected with external materials; – Style 2: Capacitors unprotected with external materials. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification should be of equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60062, Marking codes for resistors and capacitors IEC 60063, Preferred number series for resistors and capacitors IEC 60068-1:2013, Environmental testing – Part 1: General and guidance IEC 60384-1:2016, Fixed capacitors for use in electronic equipment – Part 1: Generic specification IEC 60417, Graphical symbols for use on equipment IEC 61193-2:2007, Quality assessment system – Part 2: Selection and use of sampling plans for inspection of electronic components and packages ISO 3, Preferred numbers – Series of preferred numbers SIST EN 60384-3:2016
– 8 – IEC 60384-3:2016 © IEC 2016 1.4 Information to be given in a detail specification 1.4.1 General Detail specifications shall be derived from the blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example, by an asterisk. The information given in 1.4.2 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.2 Outline drawing and dimensions There shall be an illustration of the capacitors as an aid to easy recognition and for comparison of the capacitors with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres; however, when the original dimensions are given in inches, the converted metric dimensions in millimetres shall be added. The numerical values on the body shall be given as follows: – general: width, length and height. The numerical values on the terminals shall be given as follows: – terminals: width, length and spacing. When a number of case sizes are covered b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.