Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units

This European Standard applies to machines for de-wiring bales and units and shall be used together with
EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to
machines for de-wiring bales and units, when used as intended and under conditions reasonably foreseeable
by the manufacturer as incorrect application (see clause 4).
This European Standard is not applicable to hand-held devices.
This European Standard is not applicable to machines for de-wiring bales and units which are manufactured
before the date of publication of this document by CEN.

Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und Units

Diese Europäische Norm gilt für Maschinen zur Entdrahtung von Ballen und Units und ist gemeinsam mit
EN 1034-1:2000 anzuwenden. Sie behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Maschinen zur Entdrahtung von Ballen und Units zutreffen, wenn sie bestimmungsgemäß und unter Bedingungen, die vom Hersteller als Fehlanwendung vernünftigerweise vorhersehbar sind, verwendet werden (siehe Abschnitt 4).
Diese Europäische Norm gilt nicht für handgehaltene Maschinen.
Diese Europäische Norm gilt nicht für Maschinen zur Entdrahtung von Ballen und Units, die vor der Veröffentlichung als EN hergestellt wurden.

Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines a couper les fils des balles et unités

Le présent document s‘applique aux machines a couper les fils des balles et des unités et doit etre appliqué conjointement avec l'EN 1034-1:2000. Il traite de l'ensemble des phénomenes, situations et événements dangereux significatifs qui concernent les machines a couper les fils des balles et des unités lorsque celles-ci sont utilisées normalement et dans les conditions d’utilisation abusive qui peuvent raisonnablement etre prévues par le fabricant (voir Article 4).
Cette norme n‘est pas applicable aux machines tenues a la main.
Cette norme n‘est pas applicable aux machines a couper les fils des balles et des unités, qui ont été fabriquées avant la publication de la présente norme par le CEN.

Varnost strojev – Varnostne zahteve za načrtovanje in konstrukcijo strojev in opreme za izdelavo papirja – 13. del: Stroji za razvezovanje bal in enot

General Information

Status
Withdrawn
Publication Date
30-Jun-2006
Withdrawal Date
22-Dec-2009
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
17-Dec-2009
Due Date
09-Jan-2010
Completion Date
23-Dec-2009

Relations

Buy Standard

Standard
EN 1034-13:2006
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und UnitsSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines a couper les fils des balles et unitésSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-13:2005SIST EN 1034-13:2006en01-julij-2006SIST EN 1034-13:2006SLOVENSKI
STANDARD



SIST EN 1034-13:2006



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1034-13November 2005ICS 85.100 English VersionSafety of machinery - Safety requirements for the design andconstruction of paper making and finishing machines - Part 13:Machines for de-wiring bales and unitsSécurité des machines - Exigences techniques de sécuritépour la conception et la construction de machines defabrication et de finition du papier - Partie 13: Machines àcouper les files des balles et unitès des ballesSicherheit von Maschinen - SicherheitstechnischeAnforderungen an Konstruktion und Bau von Maschinender Papierherstellung und Ausrüstung - Teil 13: Maschinenzur Entdrahtung von Ballen und UnitsThis European Standard was approved by CEN on 6 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1034-13:2005: ESIST EN 1034-13:2006



EN 1034-13:2005 (E) 2 Contents Page Introduction.4 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 List of significant hazards.7 5 Safety requirements and/or measures.9 5.1 General.9 5.2 De-wiring device and loading.9 5.3 Wire ejection device.10 5.4 Workplaces, access stairs, catwalks, passageways.10 5.5 Start-up warning device.10 5.6 Emergency stop device.10 5.7 Isolation and energy dissipation, prevention of unexpected start-up.10 5.8 Equipment for make-ready and maintenance.10 5.9 Safety measures for cleaning operations.11 5.10 Control systems and actuators.11 5.11 Integrated lighting.11 5.12 Noise.11 5.13 Ergonomic aspects.11 5.14 Electrical equipment.11 5.15 Hydraulic equipment.11 5.16 Pneumatic equipment.11 6 Verification of safety requirements and/or measures.11 7 Information for use.12 Annex ZA (informative)
Relationship between this
European
Standard and the Essential Requirements
of EU Directive 98/37/EC.13
Figures Figure 1 — Example of a machine for cutting bale wires.6 Figure 2 — Example of a machine for unit de-wiring.6 Figure 3 — Example of a machine for de-wiring cellulose bales.7
Tables
Table 1 —
List of significant hazards.8 Table 2 — Methods used to verify safety requirements and/or measures.12
SIST EN 1034-13:2006



EN 1034-13:2005 (E) 3 Foreword This European Standard (EN 1034-13:2005) has been prepared by Technical Committee CEN/TC 198 “Printing and paper machinery - Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this European Standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1034-13:2006



EN 1034-13:2005 (E) 4 Introduction This European Standard is a type C standard as stated in EN ISO 12100-1:2003.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard.
For machines that have been designed and built according to the provisions of this C standard, the following stipulation applies: When provisions of this type C standard are different from those which are stated in type B standards or from provisions made in EN 1034-1:2000, the provisions of this type C standard take precedence over the provisions of the other standards. 1 Scope This European Standard applies to machines for de-wiring bales and units and shall be used together with
EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to machines for de-wiring bales and units, when used as intended and under conditions reasonably foreseeable by the manufacturer as incorrect application (see clause 4).
This European Standard is not applicable to hand-held devices. This European Standard is not applicable to machines for de-wiring bales and units which are manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 418:1992, Safety of machinery — Emergency stop equipment — Functional aspects — Principles for design EN 619:2002, Continuous conveyors and systems — Safety and EMC requirements for mechanical conveying systems for packaged goods EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards EN 954-1:1996, Safety of machinery — Safety related parts of control systems — Part 1: General principles for design EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components —Pneumatics SIST EN 1034-13:2006



EN 1034-13:2005 (E) 5 EN 1034-1:2000, Safety of machinery — Safety requirements for the design and construction of paper making and finishing machines — Part 1: Common requirements EN 1088:1995, Safety of machinery — Interlocking devices associated with guards — Principles for design and selection EN 1837:1999, Safety of machinery — Integral lighting of machines EN 13023:2003, Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment — Accuracy categories 2 and 3 EN 60204-1:1997, Safety of machinery — Electrical equipment — Part 1: General requirements
(IEC 60204-1:1997)
EN 61000-6-2:2001, Electromagnetic compatibility (EMC) — Part 6-2: Generic standard — Immunity —
Part 2: Industrial environment (IEC 61000-6-2:1999, modified) EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004, modified) prEN 61496-2:1997, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:1997, modified) EN ISO12100-1:2003, Safety of machinery — Basic concepts — General principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts — General principles for design - Part 2: Technical principles and specifications (ISO 12100-2:2003)
3 Terms and definitions For the purpose of this European Standard, the definitions given in EN 1034-1:2000, EN ISO 12100-1:2003 and the following apply: 3.1 machine for de-wiring bales and units
machinery used for cutting and or opening and removing wires used for binding together bales made of cellulose or paper and units formed of cellulose bales. This machinery includes the de-wiring device, integrated continuous conveyor for moving the bales and units, the loading conveyor, the positioning device and the wire ejection device, including the drive and control systems.
Examples of machine types are illustrated in Figures 1, 2 and 3.
SIST EN 1034-13:2006



EN 1034-13:2005 (E) 6
NOTE Safety devices are not shown Key 1 Loading
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.