SIST EN 10028-4:2017
(Main)Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.
Flacherzeugnisse aus Druckbehälterstählen - Teil 4: Nickellegierte kaltzähe Stähle
Diese Europäische Norm legt Anforderungen an Flacherzeugnisse für Druckbehälter aus den nickellegierten Stählen nach Tabelle 1 fest.
Zusätzlich gelten die Anforderungen und Begriffe in EN 10028-1:2017.
ANMERKUNG Nach Veröffentlichung dieser Europäischen Norm im EU Amtsblatt (OJEU) unter der Richtlinie 2014/68/EU ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 2014/68/EU auf die technischen Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und der entsprechende Teil der Normenreihe) beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den ESR der Richtlinie 2014/68/EU entsprochen wird.
Produits plats en aciers pour appareils à pression — Partie 4 : Aciers alliés au nickel avec caractéristiques spécifées à basse temperature
La présente Norme européenne spécifie les prescriptions relatives aux produits plats pour appareils à pression en aciers alliés au nickel, telles que spécifiées dans le Tableau 1.
Les exigences de la EN 10028-1:2017 s’appliquent également.
NOTE Dès lors que la présente Norme européenne est publiée dans le Journal Officiel de l’Union européenne (JOUE) en lien avec la Directive 2014/68/UE, la présomption de conformité aux Exigences Essentielles de Sécurité (ESRs) de la Directive 2014/68/UE se limite aux données techniques des matériaux de la présente Norme européenne (Partie 1 et l’autre partie pertinente de la série) et ne suppose pas l'adéquation des matériaux avec un appareil en particulier. Par conséquent, il doit être procédé à l’évaluation des données techniques spécifiées dans la présente norme de matériaux par rapport aux exigences concernant la conception de cet équipement spécifique, afin de vérifier que les exigences essentielles de sécurité de la Directive 2014/68/UE soient satisfaites.
Ploščati jekleni izdelki za tlačne posode - 4. del: Jekla, legirana z nikljem, s specificiranimi lastnostmi pri nizkih temperaturah
Ta evropski standard določa zahteve za ploščate izdelke za tlačno opremo, izdelano iz jekla nikljeve zlitine.
General Information
- Status
- Published
- Public Enquiry End Date
- 08-Feb-2015
- Publication Date
- 07-Aug-2017
- Technical Committee
- IFEK - Ferrous metals
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 07-Aug-2017
- Due Date
- 12-Oct-2017
- Completion Date
- 08-Aug-2017
Relations
- Effective Date
- 02-Aug-2017
- Effective Date
- 01-Jan-2015
Overview
EN 10028-4:2017 - Flat products made of steels for pressure purposes, Part 4: Nickel alloy steels with specified low temperature properties (CEN) - specifies requirements for flat steel products intended for pressure equipment that are made from nickel-alloy steels. The standard sets out chemical composition limits, mechanical properties, impact energy requirements at low temperatures, delivery and heat‑treatment conditions, inspection/testing and marking for these grades. The general requirements and definitions of EN 10028-1:2017 also apply.
Key topics and requirements
- Scope and applicability: Applies to flat products (plates, semi‑products) for pressure equipment made of nickel alloy steels listed in the standard (see Table 1).
- Chemical composition & tolerances: Cast analysis limits and permissible product-analysis deviations are specified (see Tables 1–2).
- Mechanical properties: Minimum yield, tensile strength and elongation values are given by grade and delivery condition (see Table 3).
- Low temperature impact energy: Minimum KV2 impact energy values at specified temperatures are provided by grade, thickness and direction; options for a 40 J minimum may be agreed (see Table 4).
- Delivery and heat treatment: Standard delivery conditions (+N, +NT, +QT and variants) are defined; Annex A gives heat‑treatment guidance.
- Inspection & testing: Types of inspection documents, sampling, test methods (including impact test variations such as mid-thickness or longitudinal verification) and marking are covered. Inspection certificate 3.1 (EN 10204) is referenced in ordering examples.
- Compliance note: When cited under Directive 2014/68/EU, presumption of conformity is limited to the material technical data - designers must still verify material adequacy for specific equipment against essential safety requirements.
Applications and who uses it
EN 10028-4:2017 is used by:
- Materials engineers and metallurgists specifying nickel-alloy steel plates for pressure systems
- Designers and structural engineers of pressure vessels, boilers and cryogenic equipment requiring low temperature properties
- Fabricators, welders and testing laboratories performing material verification, impact testing and heat treatment
- Procurement and quality teams requiring inspection certificates and conformity documentation
- Notified bodies and inspectors assessing compliance with pressure equipment directives
Typical sectors: petrochemical, LNG and cryogenic systems, power generation, and industrial pressure equipment where nickel-alloy steels are selected for toughness at low temperatures.
Related standards
- EN 10028-1:2017 - General requirements (normative references and definitions)
- EN 10204:2004 - Inspection documents (inspection certificate types)
- Directive 2014/68/EU - Essential safety requirements for pressure equipment (informative relationship in Annex ZA)
Keywords: EN 10028-4:2017, nickel alloy steels, flat products, pressure equipment, low temperature properties, impact energy, chemical composition, heat treatment, EN 10028-1, EN 10204.
Frequently Asked Questions
SIST EN 10028-4:2017 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties". This standard covers: This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1. The requirements and definitions of EN 10028-1:2017 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.
This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1. The requirements and definitions of EN 10028-1:2017 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.
SIST EN 10028-4:2017 is classified under the following ICS (International Classification for Standards) categories: 77.140.30 - Steels for pressure purposes; 77.140.50 - Flat steel products and semi-products. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 10028-4:2017 has the following relationships with other standards: It is inter standard links to SIST EN 10028-4:2009, SIST EN 10028-4:2009. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 10028-4:2017 is associated with the following European legislation: EU Directives/Regulations: 2014/68/EU, 97/23/EC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 10028-4:2017 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flacherzeugnisse aus Druckbehälterstählen - Teil 4: Nickellegierte kaltzähe StähleProduits plats en aciers pour appareils à pression — Partie 4 : Aciers alliés au nickel avec caractéristiques spécifées à basse temperatureFlat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10028-4:2017SIST EN 10028-4:2017en,fr,de01-oktober-2017SIST EN 10028-4:2017SLOVENSKI
STANDARDSIST EN 10028-4:20091DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10028-4
July
t r s y ICS
y yä s v rä u râ
y yä s v rä w r Supersedes EN
s r r t zæ vã t r r {English Version
Flat products made of steels for pressure purposes æ Part
vã Nickel alloy steels with specified low temperature properties Produits plats en aciers pour appareils à pression æ Partie
v ã Aciers alliés au nickel avec caractéristiques spécifiées à basse température
Flacherzeugnisse aus Druckbehälterstählen æ Teil
vã Nickellegierte kaltzähe Stähle This European Standard was approved by CEN on
y May
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r r t zæ vã t r s y ESIST EN 10028-4:2017
Guidelines for heat treatment . 12 Annex B (informative)
Changes to the previous version EN 10028-4:2009 . 13 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of Directive 2014/68/EU aimed to be covered . 14
...
記事タイトル：SIST EN 10028-4:2017 - 圧力容器用ニッケル合金鋼の低温特性を指定した平板製品 記事の内容：この欧州標準は、ニッケル合金鋼製の圧力装置用の平板製品に関する要件を規定しています。
The article discusses the European Standard known as EN 10028-4:2017, which provides specifications for flat steel products used in pressure equipment made of nickel alloy steels.
기사 제목: SIST EN 10028-4:2017 - 압력용 제품으로 제작된 니켈 합금 강판 - 제 4 부: 특정 저온 특성을 갖는 니켈 합금 강판 기사 내용: 이 유럽 표준은 니켈 합금 강판으로 제작된 압력 장비용 평판 제품에 대한 요구사항을 명시합니다.
The article explains that the European Standard, SIST EN 10028-4:2017, outlines the requirements for flat products made of nickel alloy steels used in pressure equipment.
기사 제목: SIST EN 10028-4:2017 - 압력용 강판 제조를 위한 니켈 합금강의 특정 저온 특성을 갖는 평면 제품 기사 내용: 이 유럽 표준은 니켈 합금강으로 만든 압력 장치용 평면 제품에 대한 요구 사항을 명시합니다.
記事のタイトル：SIST EN 10028-4:2017 - 圧力用ニッケル合金鋼の製造 - 第4部：指定された低温特性を持つ平鋼製品 記事の内容：この欧州規格は、圧力設備用に製造されたニッケル合金鋼の平鋼製品に対する要件を規定しています。
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...