SIST EN 12629-4:2001+A1:2010

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines

This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to concrete roof tile making machines. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium-silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. Limits of the machine The tile making machine is considered to begin at the point where moulds and/or the concrete are delivered to the fixed part of the machine and ends after the tile cutting process where products on their moulds are delivered on to an outfeed conveyor (see Annexes A and B). Moulds and concrete may be delivered to and removed from the machine by hand. The preparation of the concrete mixture and the transport from the mixer to the machine are not covered by this standard. The equipment for the transport and handling of formed products is not covered by this standard. This European Standard deals with all significant hazards pertinent to these machines, including the interfaces, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard establishes safety requirements and/or methods of protection which applies to these machines.

Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 4: Beton-Dachsteinmaschinen

Diese Europäische Norm legt die Sicherheitsanforderungen für Maschinen, die Betondachsteine herstellen fest. Die Dachsteinmaschine ist nur ein Teil des gesamten Dachsteinherstellungsprozesses, der aus einer Anzahl miteinander verknüpfter Teile bestehen kann.

Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 4 : Machines pour la fabrication de tuiles en béton

La présente partie de l'EN 12629, utilisée avec l'EN 12629-1:2000+A1:2010, s'applique aux machines
pour la fabrication de tuiles en béton.
L'EN 12629-1:2000+A1:2010 spécifie les prescriptions générales applicables aux machines pour la fabrication
de produits de construction en béton et silico-calcaire.
Le présent document spécifie les prescriptions supplémentaires et/ou les dérogations à l’EN 12629-1:2000+A1:2010
spécifiques aux machines concernées."

Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 4. del: Stroji za izdelavo betonskih strešnikov

Ta del EN 12629 skupaj z EN 12629-1:2000+A1:2010 velja za stroje za izdelavo betonskih strešnikov. EN 12629-1:2000+A1:2010 določa splošne zahteve, ki veljajo za stroje za izdelavo gradbenih proizvodov iz betona in apnenega peščenca. Ta dokument določa dodatne zahteve in/ali odstopanja od EN 12629-1:2000+A1:2010, specifične za stroje, ki jih zajema. Omejitve stroja: Velja, da stroj za izdelavo strešnikov začne delati na točki, na kateri kalupi in/ali beton prihajajo do fiksnega dela stroja, in zaključi po rezanju strešnikov, ko proizvodi v svojih kalupih pridejo na izhodni transporter (glej Dodatka A in B). Kalupi in beton se lahko ročno vstavljajo v stroj in odstranjujejo z njega. Ta standard ne zajema priprave betonskih zmesi in prevoza z mešalnika do stroja. Ta standard ne zajema opreme za prevoz in delo z oblikovanimi proizvodi. Ta evropski standard obravnava vse pomembne nevarnosti, ki se nanašajo na te stroje, vključno z vmesniki, kadar se uporabljajo kot predvideno in pod pogoji napačne uporabe, ki jih razumno predvidi proizvajalec (glej Klavzulo 4). Ta evropski standard določa primerne tehnične ukrepe za odpravo ali zmanjšanje tveganj, ki se pojavijo zaradi pomembnih nevarnosti. Ta standard vzpostavlja varnostne zahteve in/ali zaščitne metode, ki veljajo za te stroje.

General Information

• Status: Published
• Publication Date: 19-Oct-2010
• ICS: 91.220 - Construction equipment
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Oct-2010
• Due Date: 18-Dec-2010
• Completion Date: 20-Oct-2010
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 12629-4:2001+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines

Relations

• Consolidates: SIST EN 12629-4:2001 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines
• Effective Date: 01-Dec-2010
• Consolidates: SIST EN 12629-4:2001/kFprA1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4: Concrete roof tile making machines
• Effective Date: 10-Jul-2010
• Consolidates: SIST EN 12629-4:2001 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines
• Effective Date: 18-Jan-2023
• Consolidates: SIST EN 12629-4:2001/kFprA1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4: Concrete roof tile making machines
• Effective Date: 18-Jan-2023
• Consolidates: SIST EN 12629-4:2001 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines
• Effective Date: 19-Jan-2023
• Consolidates: SIST EN 12629-4:2001/kFprA1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4: Concrete roof tile making machines
• Effective Date: 19-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 4: Beton-DachsteinmaschinenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 4 : Machines pour la fabrication de tuiles en bétonMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-4:2001+A1:2010SIST EN 12629-4:2001+A1:2010en,fr01-december-2010SIST EN 12629-4:2001+A1:2010SLOVENSKI
STANDARD



SIST EN 12629-4:2001+A1:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-4:2001+A1
September 2010 ICS 91.220 Supersedes EN 12629-4:2001English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4: Concrete roof tile making machines
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 4: Machines pour la fabrication de tuiles en béton
Maschinen für die Herstellung von Bauprodukten aus Betonund Kalksandsteinmassen - Sicherheit - Teil 4: Beton-Dachsteinmaschinen This European Standard was approved by CEN on 1 January 2001 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-4:2001+A1:2010: ESIST EN 12629-4:2001+A1:2010



EN 12629-4:2001+A1:2010 (E)
2
Contents Foreword . 3Introduction . 41Scope . 42Normative references . 53!!!!Terms and definitions"""" . 54List of significant hazards . 64.1Mechanical Hazards . 64.1.1Crushing hazards . 64.1.2Shearing hazards . 64.1.3Cutting and severing hazards . 64.1.4Entanglement hazards . 64.1.5Drawing - In or trapping hazards . 74.1.6Impact hazards. 74.1.7High pressure fluid ejection . 74.1.8Ejection of parts or materials . 74.1.9Slip, trip and fall hazards . 74.2Noise Hazards . 74.3Hazards from materials used . 74.3.1Contact or inhalation . 74.3.2Fire or explosion . 74.4Hazards generated by neglecting ergonomic principles in design. 74.4.1Neglected use of personal protective equipment . 74.4.2Inadequate local lighting . 74.4.3Human error . 75!!!!Safety requirements and/or protective measures"""" . 85.1General . 85.2Mechanical hazards . 85.2.1Propulsion unit and cutting unit and extrusion unit . 85.2.2Press unit and its interfaces . 85.2.3Slip, trip and fall hazards . 85.2.4Contact . 85.2.5Control panel . 86!!!!Verification of safety requirements and/or protective measures"""" . 87!!!!Information for use"""" . 98Warnings . 99Marking . 9Annex A (informative)
First typical concrete tile manufacturing plant . 10Annex B (informative)
Second typical concrete tile manufacturing plant . 11Annex ZA (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 12Bibliography . 13SIST EN 12629-4:2001+A1:2010



EN 12629-4:2001+A1:2010 (E)
3
Foreword This document (EN 12629-4:2001+A1:2010) has been prepared by Technical Committee CEN/TC 151 "Construction equipment and building material machines - Safety ", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-4:2001. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. !deleted text" !The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety" consists of following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete rooftile making machines Part 5.1: Concrete pipe machines manufacturing in the vertical axis Part 5.2: Concrete pipe machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for the benched manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12629-4:2001+A1:2010



EN 12629-4:2001+A1:2010 (E)
4
Introduction !This European Standard is a Type C-standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situation and events are covered are indicated in the scope of this document.
When provisions of this type C document are different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of the other documents, for machines that have been designed and built according to the provisions of this type C document.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the concrete roof tile making machines as described in 1.1. With the aim of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it:  specific conditions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner,  the equipment will only be used by competent and designated persons,
 the place of use/installation is adequately lit,
 all operations are carried out by specially trained operators."
1 Scope ! 1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to concrete roof tile making machines. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to a
...