SIST EN ISO 15527:2022
(Main)Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2022)
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2022)
This document specifies the requirements and test methods for solid flat compression-moulded sheets
of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials. It
applies only to thicknesses from 10 mm to 200 mm.
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen und Prüfverfahren (ISO 15527:2022)
Dieses Dokument legt die Anforderungen und Prüfverfahren an massive ebene gepresste Tafeln aus Polyethylen (PE-UHMW und PE-HD, siehe ISO 1043-1) ohne Füll- oder Verstärkungsstoffe fest. Sie gilt nur für Tafeldicken von 10 mm bis 200 mm.
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) - Exigences et méthodes d'essai (ISO 15527:2022)
Le présent document spécifie les exigences et les méthodes d'essai pour les plaques moulées par compression, compactes et planes, en polyéthylène (PE-UHMW et PE-HD, voir l'ISO 1043-1) sans charges ni matériaux de renforcement. Il s'applique uniquement aux plaques d’épaisseur comprise entre 10 mm à 200 mm.
Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-HD) - Zahteve in preskusne metode (ISO 15527:2022)
Ta dokument določa zahteve in preskusne metode za masivne ravne kompresijsko brizgane polietilenske plošče (PE-UHMW in PE-HD, glej standard ISO 1043-1) brez polnil ali materialov za ojačanje. Uporablja se le za debeline od 10 do 200 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15527:2022
01-april-2022
Nadomešča:
SIST EN ISO 15527:2019
Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-
HD) - Zahteve in preskusne metode (ISO 15527:2022)
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO 15527:2022)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO 15527:2022)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO 15527:2022)
Ta slovenski standard je istoveten z: EN ISO 15527:2022
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 15527:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15527:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 15527:2022
EN ISO 15527
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2022
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15527:2018
English Version
Plastics - Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) - Requirements and test methods (ISO
15527:2022)
Plastiques - Plaques moulées par compression en Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-
polyéthylène (PE-UHMW, PE-HD) - Exigences et UHMW, PE-HD) - Anforderungen und Prüfverfahren
méthodes d'essai (ISO 15527:2022) (ISO 15527:2022)
This European Standard was approved by CEN on 23 January 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15527:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15527:2022
EN ISO 15527:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15527:2022
EN ISO 15527:2022 (E)
European foreword
This document (EN ISO 15527:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall
be withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15527:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15527:2022 has been approved by CEN as EN ISO 15527:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15527:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 15527:2022
INTERNATIONAL ISO
STANDARD 15527
Fourth edition
2022-02
Plastics — Compression-moulded
sheets of polyethylene (PE-UHMW,
PE-HD) — Requirements and test
methods
Plastiques — Plaques moulées par compression en polyéthylène (PE-
UHMW, PE-HD) — Exigences et méthodes d'essai
Reference number
ISO 15527:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 15527:2022
ISO 15527:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15527:2022
ISO 15527:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material. 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . . 2
5.2.3 Rectangularity . 2
5.3 Properties . 3
5.3.1 Physical properties. 3
5.3.2 Physiological behaviour . 3
6 Test methods . 3
6.1 Test specimens. 3
6.1.1 Preparation of test specimens . 3
6.1.2 Conditioning . 4
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h . 5
6.4.2 Length, l, and width, b . . . 5
6.4.3 Rectangularity . 5
6.5 Density . 5
6.6 Determination of abrasion properties . 5
6.7 Tensile stress at yield, σ , and tensile strain at yield, ε . 5
y y
6.8 Modulus of elasticity in tension, E . 5
t
6.9 Impact strength of notched specimens . 6
6.9.1 Charpy impact strength of double-notched specimens . 6
6.9.2 Charpy impact strength of single-notched specimens, a . 6
cN
6.10 Melt mass-flow rate (MFR) . 6
7 Designation and order specification . 6
8 Marking . . 6
Annex A (normative) Requirements for rectangularity . 7
Annex B (normative) Determination of abrasion properties . 8
Annex C (informative) Example of apparatus for the determination of abrasion properties .10
Bibliography .11
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 15527:2022
ISO 15527:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations recei
...
SLOVENSKI STANDARD
oSIST prEN ISO 15527:2021
01-junij-2021
Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-
HD) - Zahteve in preskusne metode (ISO/DIS 15527:2021)
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO/DIS 15527:2021)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO/DIS 15527:2021)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO/DIS 15527:2021)
Ta slovenski standard je istoveten z: prEN ISO 15527
ICS:
83.140.10 Filmi in folije Films and sheets
oSIST prEN ISO 15527:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15527:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15527:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15527
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2021-03-29 2021-06-21
Plastics — Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) — Requirements and test methods
Plastiques — Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) — Exigences et
méthodes d'essai
ICS: 83.140.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15527:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15527:2021
ISO/DIS 15527:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15527:2021
ISO/DIS 15527:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material . 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . 2
5.2.3 Rectangularity . 2
5.3 Properties . 3
5.3.1 Physical properties . 3
5.3.2 Physiological behaviour . . 3
6 Test methods . 3
6.1 Test specimens . 3
6.1.1 Preparation of test specimens . 3
6.1.2 Conditioning . 4
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h .5
6.4.2 Length, l, and width, b .5
6.4.3 Rectangularity . 5
6.5 Density . 5
6.6 Determination of abrasion properties . 5
6.7 Tensile stress at yield, σ , and tensile strain at yield, ε .
y y 5
6.8 Modulus of elasticity in tension, E .
t 5
6.9 Impact strength of notched specimens . 6
6.9.1 Charpy impact strength of double-notched specimens . 6
6.9.2 Charpy impact strength of single-notched specimens, a .
cN 6
6.10 Melt mass-flow rate (MFR) . 6
7 Designation . 6
8 Marking . 6
Annex A (normative) Requirements for rectangularity . 7
Annex B (normative) Determination of abrasion properties . 8
Annex C (informative) Example of apparatus for the determination of abrasion properties .10
Bibliography .11
© ISO 2021 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15527:2021
ISO/DIS 15527:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This fourth edition cancels and replaces the third edition (ISO 15527:2018), which has been technically
revised. The changes compared to the previous edition are as follows:
— The minimum value of double-notched impact strength for PE-UHMW group 1.1 in Table 2 has been
2 2
changed from >40 kJ/m to >80 kJ/m .
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15527:2021
DRAFT INTERNATIONAL STANDARD ISO/DIS 15527:2021(E)
Plastics — Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) — Requirements and test methods
1 Scope
This document specifies the requirements and test metho
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.